• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3828-3837
• /
• 1996

The dynamic problems of interface crack propagated with constant velocity along the interface of bimateraial composed of isotropic and orthotropicmaterial under antiplane loading condition are studied in this paper. The general dynamic stress fields and displacement fields of mode III are derived when interface crack between isotropic and orthotropic material is propagating with constant velocity. The general dynamic stress fields and displacement fields in isotropic material. Finally, the characteristics of interface crack propagation are studied with various properties of isotropic and orthotropic material and crack propagarion velocities.

• Journal of Adhesion and Interface
• /
• v.3 no.3
• /
• pp.1-6
• /
• 2002

We invested which is major one in rubber materials design factors affecting on noise and showed the design guide for low noise tire development in this study. Tire noise and impact noise for rubber sheets were tested at anechoic room. Hardness, tensile and dynamic mechanical properties were also measured using the rubber sheets. A major design factor of rubber materials affecting on the tire noise was hardness or 300% modulus. There was also positive correlation between two properties. Therefore, designing rubber materials to have low hardness or 300% modulus can reduce noise.

• Elastomers and Composites
• /
• v.53 no.4
• /
• pp.195-201
• /
• 2018

Three kinds of rubber compounds were prepared, and their underwater acoustical properties were investigated for anechoic coating. Dynamic mechanical properties of the rubber compounds were measured using a dynamic mechanical analyzer and extended to 100 kHz using time-temperature superposition. The sound speed, reflection coefficient, and attenuation constant were calculated. Silicone rubber showed the lowest reflection coefficient, and nitrile rubber showed the highest attenuation constant. The acoustic properties of nitrile rubber compounds with various compositions were investigated. The sound speed, reflection coefficient, and transmission coefficient of the nitrile rubber in the frequency range of 200-1000 kHz were measured in a water-filled tank.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.3-8
• /
• 2001

Dynamic stress intensity factors (DSIFs) are obtained when a crack propagates with constant velocity in rectangular functionally gradient materials (FGMs) under dynamic mode III load. To obtain the dynamic stress intensity factors, it is used the general stress and displacement fields of FGMs for propagating crack and the boundary collocation method (BCM). The stress intensity factors and energy release rates are the greatest in the increasing properties $(\xi>0)$, next constant properties $(\x=0)$ and decreasing properties $(\xi<0)$ under constant crack tip properties and crack tip speed.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.139-144
• /
• 2002

In this study, the PPS/ABS blend system was investigated in order to identify the relationship between the incorporation of compatabilizing moieties and the mechanical properties. ABS resin was chemically modified by the incorporation of maleic anhydride using reactive extrusion method to yield MABS resin, and PPS/MABS blend was prepared by a twin screw extruder. Single glass transition behavior was observed in the various compositions of PPS/MABS blend by dynamic mechanical analysis study. Upon the examination of the mechanical properties, the PPS/MABS blend exhibited an enhanced tensile, flexural and impact strength, which might be due to the better chemical compatibilization to result in the reduced interfacial tension between each components.

• International Journal of Automotive Technology
• /
• v.4 no.3
• /
• pp.149-156
• /
• 2003

This paper is concerned with the energy absorption efficiency of auto-body side structures for the conventional steel and 60TRIP high strength steel. In order to evaluate the energy absorption efficiency, the dynamic crash analysis is carried out with the regulation of US-SINCAP. The analysis adopts the Johnson-Cook model for the dynamic material properties, which have been obtained from dynamic material tests. For the sake of the dynamic material properties, the analysis has been accurately peformed for the crashworthiness assesment. The analysis result provides deformed shapes, amounts of penetration and accelerations at several important points during crash. The result confirms that 60TRIP greatly improves the crashworthiness of the side members without sacrificing the weight and thus can be used for the light-weight design of an auto-body.

• Interaction and multiscale mechanics
• /
• v.5 no.2
• /
• pp.115-129
• /
• 2012

Nanowires (NWs) have attracted intensive researches owing to the broad applications that arise from their remarkable properties. Over the last decade, immense numerical studies have been conducted for the numerical investigation of mechanical properties of NWs. Among these numerical simulations, the molecular dynamics (MD) plays a key role. Herein we present a brief review on the current state of the MD investigation of nanowires. Emphasis will be placed on the FCC metal NWs, especially the Cu NWs. MD investigations of perfect NWs' mechanical properties under different deformation conditions including tension, compression, torsion and bending are firstly revisited. Following in succession, the studies for defected NWs including the defects of twin boundaries (TBs) and pre-existing defects are discussed. The different deformation mechanism incurred by the presentation of defects is explored and discussed. This review reveals that the numerical simulation is an important tool to investigate the properties of NWs. However, the substantial gaps between the experimental measurements and MD results suggest the urgent need of multi-scale simulation technique.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.53-67
• /
• 1996

The dynamic characteristics of mechanical structure are strongly affected by the properties of joint parameters. In this study, the test structures are constructed with two beams which are clamped by bolts, and a bolted joint which is modelled as a lumped stiffness element. To idientify the dynamic joint parameters with variance of clamping torque of bolts, the sensitivity analysis and the mode energy analysis methods are investigated experimentally. As a reult of these two methods, stiffnesses of bolted joint are experimentally found to increase as the clamping torque increases. These stiffnesses identified from the sensitivity analysis and the mode energy analysis method have some difference.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.139-148
• /
• 1998

Internal and external heat sources will cause to deform to machine elements in the contact joint of structure, which results in the change of contact pressure distribution different from initial assembly. Heat induced variations of contact pressure will change the static and dynamic properties such as contact stiffness, damping as well as contact heat conduction in the structure In order to design and control the intelligent machine tool operating in variant conditions more sophisticatedly, the good prediction for the changes of prescribed properties are strongly required especially in the contact elements adjacent to the rotational or linear bearing. This paper presents some computational and experimental results in regard to static and dynamic characteristics of the press-fitted bush and shaft assembly which is a model of the bearing innerrace and shaft assembly. In the condition of heat generation on the outer surface of the bush, the effects of changes in the negative clearance and the heat flux on pressure distribution and dynamic properties are investigated. Results of this study show that the edge effect of the bush and the initial clearance have effects on the transient dynamic characteristics significantly.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.553-562
• /
• 2013

Vehicle vibrations arise from engine and road surface excitations. The engine mount system of a passenger car sustains the engine weight and insulates the excitation force from the engine system. The dynamic properties of viscoelastic material used for the vehicle engine mounts have large variation due to environmental factors such as environmental temperature and humidity etc. The present study aims to investigate the variability of dynamic characteristics in rubber engine mounts considering both environmental temperature change and material model errors/uncertainty. The engine mounts for a passenger car were modeled using finite element method. Then, the dynamic stiffness variability of the engine mounts were estimated using Monte Carlo simulation method. In order to estimate the variations in the storage and loss moduli of the viscoelastic materials, the material properties of the synthetic rubber were expressed as a fractional-derivative model. Next, in order to simulate the uncertainty propagation of the dynamic stiffness for the engine mounts due to the storage and loss moduli variations, the Monte Carlo simulation was used. The Monte Carlo simulation results showed large variation of the engine-mount stiffness along frequency axis.