• 한국재난정보학회 논문집
• /
• 제7권3호
• /
• pp.206-219
• /
• 2011

포장 설계기준에서 중요한 요인은 응력과 변형률 분포도이다. 합리적인 응력과 변형률 분포도를 달성하기 위한 차량타이어의 접촉면적과 공기압은 매우중요하다. 본 연구에서는 이동하중 하에서 연성포장의 점탄성 특성에 관한 내용을 다루고 있으며 현장 측정시험을 통하여 실제 도로의 종횡변형률을 수치해석 결과와 비교분석 하였다. 포장거동에 대한 차량이동하중의 영향을 적절히 모사하기 위하여 단계하중을 이용한 3차원 유한요소 해석이 수행되었다. 점탄성 해석을 위하여 아스팔트 혼합물의 이완계수, E(t), 가 실험실에서 제작된 시료의 실험으로부터 측정되었다. 현장조사 결과에 의하면, 종횡변형률은 서로 상이한 값을 보였으며 전반적으로 변형률의 크기는 차량의 속도가 증가함에 따라 감소함을 보였다. 전반적으로 횡방향 변형률은 종방향 변형률에 비하여 작은값을 보였으며 그 차이는 횡방향에서 더욱 두드러진 경향을 보였다.

• Wind and Structures
• /
• 제6권3호
• /
• pp.221-248
• /
• 2003

The design of high-rise building is often influenced by wind-induced motions such as accelerations and lateral deflections. Consequently, the building's structural stiffness and dynamic (vibration periods and damping) properties become important parameters in the determination of such motions. The approximate methods and empirical expressions used to quantify these parameters at the design phase tend to yield values significantly different from each other. In view of this, there is a need to examine how actual buildings in the field respond to dynamic wind loading in order to ascertain a more realistic model for the dynamic behavior of buildings. This paper describes the findings from full-scale measurements of the wind-induced response of typical high-rise buildings in Singapore, and recommends an empirical forecast model for periods of vibration of typical buildings in Singapore, an appropriate computer model for determining the periods of vibration, and appropriate expressions which relate the wind speed to accelerations in buildings based on wind tunnel force balance model test and field results.

• 대한의용생체공학회:의공학회지
• /
• 제21권2호
• /
• pp.213-218
• /
• 2000

Pressure distributions of the soft tissue are valuable for understanding and diagnosing the disease characteristics due to the mechanical loading. Our system measures dynamic pressure distributions in real-time under the general PC environment, and analyzes various foot disorders. Main features of the developed system are as follows: (1) With the resistive pressure sensor matrix of 40${\times}$40 cells, the data is sent to the PC with the maximum sampling rate of 40 frames/sec. (2) For each frame, contact area, pressure and force are analyzed by graphic forms. Thus, various biomechanical parameters are easily determined at specific areas of interests. (3) A certain stance phase can be chosen for the analysis from the continuous walking, and the detailed biomechanical analysis can be done according to an arbitrary line dividing anterior/posterior or medial/lateral plantar areas. (4) The center of pressure (COP) is calculated and traced from the pressure distribution data, and thus the movement of the COP is monitored in detail. A few experiments revealed that our system successfully measured the dynamic plantar distribution during normal walking.

• 한국철도학회논문집
• /
• 제20권3호
• /
• pp.299-310
• /
• 2017

본 연구에서는 3-piece 마찰 웨지 화차의 주행성능을 예측하기 위해 ADAMS/View에서 독립하중 마찰 웨지 모델을 개발하였다. 마찰 웨지 모델은 볼스터의 좌우, 수직방향에 따른 마찰을 각각 구현해줄 수 있다. 개발된 마찰 웨지 모델은 ADAMS/Rail 차량 모델에 적용하여 동역학 해석 결과를 얻었다. 대상차량은 임계속도 210km/h를 가진다. 직선 안정성 해석에서 UIC518에 근거해 차체의 횡, 수직방향 한계 가속도에 만족하는 것을 확인하였다. 300R 곡선에서 해석 적용 속도는 70km/h로 UIC518에 근거해 차체, 대차의 한계 가속도에 만족하였다. 또한 "철도차량 안전기준에 관한 규칙"의 윤중감소율, 횡압, 탈선계수에 만족하는 것을 확인하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.472-476
• /
• 2003

A real train load fluctuates along the track because of complicated movements(Bouncing, Rolling, Pitching and Yawing) and rail conditions. This research has for its object in development of a numerical train load model including fluctuation characteristics of lateral forces. It is based on Klingel movement theory of a wheelset on straight track. it presents a propriety of application by comparison between a 3D-Numerical analysis result using this train load model and a measured data. And this paper presents further study subject to improve a method about the train load modeling.

• Structural Engineering and Mechanics
• /
• 제31권4호
• /
• pp.423-437
• /
• 2009

In order to perform a step-by-step force-displacement response analysis or dynamic time-history analysis of large buildings with masonry infilled R/C frames, a continuous force-deformation model based on an equivalent strut approach is proposed for masonry infill panels containing openings. The model, which is applicable for degrading elements, can be implemented to replicate a wide range of monotonic force-displacement behaviour, resulting from different design and geometry, by varying the control parameters of the model. The control parameters of the proposed continuous model are determined using experimental data. The experimental program includes fifteen 1/3-scale, single-story, single-bay reinforced concrete frame specimens subjected to lateral cyclic loading. The parameters investigated include the shape, the size, the location of the opening and the infill compressive strength. The actual properties of the infill and henceforth the characteristics needed for the diagonal strut model are based on the assessment of its lateral resistance by the subtraction of the response of the bare frame from the response of the infilled frame.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.107-114
• /
• 2001

When group pile supporting structures are to be subjected to large lateral loads, generally, hatter piles are used in group pile with vertical piles. It is well known that batter piles resist lateral static loads which are acted upon the piles as axial farces quite well but, they show a poor performance under seismic loads. However, it is not yet known how the batter piles behave under dynamic loading and how to strengthen the batter piles to improve the seismic performance. Shaking table tests were performed to investigate the seismic behavior of the batter pile and to bring up the countermeasures to improve the seismic performance. As the result of the shaking table tests, batter piles failed due to not only the excessive increase of compressive force near the pile head but also that of tensile force. In case that the pile head was connected with pile cap by rubber joint, the max. acceleration at the pile cap was reduced due to the high damping ratio of rubber and the max. moment and max. axial farce at the pile head was decreased remarkably. When the inclinations(V:H) of the batter pile were 8:3 and 8:4, max. moment, max. shear force, and max. axial farce were reduced notably and max. acceleration and max. displacement at the pile cap was diminished, too.

• 한국항해학회지
• /
• 제10권2호
• /
• pp.139-155
• /
• 1986

In this paper the dynamic effects due to the free water motions in tanks upon the lateral motion of a floating body in regular waves are calculated, in order to obtain the relationship between a motion of a floating body and that of the free water in tanks. Under the assumption that the fluid is ideal and motion amplitudes are small, velocity potential of the fluid in tanks is calculated by the source distribution method and the hydrodynamic forces and moments are calculated by the integration of fluid pressures over the tank surface. Hydrodynamic effects of the fluid on the floating body are expressed in terms of added mass and coupling coefficient obtained from the integration. Computations are carried out for ship with seven wide center tanks and comparisons between the liquid cargo loading case and the rigid cargo loading case are shown.

• Structural Engineering and Mechanics
• /
• 제81권3호
• /
• pp.317-333
• /
• 2022

Visco-Plastic Damper (VPD) as a passive energy dissipation device with dual behavior has been recently numerically studied. It consists of two bent steel plates and segments with a viscoelastic solid material in between, combining and improving characteristics of both displacement-dependent and velocity-dependent devices. In order to trust the performance of VPD, for the 1st time this paper experimentally investigates prototype damper behavior under a wide range of frequency and amplitude of dynamic loading. A high-axial damping rubber is innovatively proposed as the viscoelastic layer designed to withstand large axial strains and dissipate energy accordingly. Test results confirmed all assumptions about VPD. The behavior of VPD subjected to low levels of excitation is elastic while with increasing levels of excitation, a significant source of energy dissipation is provided through the yielding of the steel elements in addition to the viscoelastic energy dissipation. The results showed energy dissipation of 99.35 kN.m under a dynamic displacement with 14.095 mm amplitude and 0.333 Hz frequency. Lateral displacement at the middle of the device was created with an amplification factor obtained ranging from 2.108 to 3.242 in the rubber block. Therefore, the energy dissipation of viscoelastic material of VPD was calculated 18.6 times that of the ordinary viscoelastic damper.

• Journal of Advanced Research in Ocean Engineering
• /
• 제1권4호
• /
• pp.239-251
• /
• 2015

In this study, a spectral fatigue analysis was performed for the topside structure of an offshore floating vessel. The topside structure was idealized using beam elements in the SACS program. The fatigue analysis was carried out considering the wave and wind loads separately. For the wave-induced fatigue damage calculation, motion RAOs calculated from a direct wave load analysis and regular waves with different periods and unit wave heights were utilized. Then, the member end force transfer functions were generated covering all the loading conditions. Stress response transfer functions at each joint were produced using the specified SCFs and member end force transfer functions. fatigue damages were calculated using the obtained stress ranges, S-N curve, wave spectrum, heading probability of each loading condition, and their corresponding occurrences in the wave scatter diagrams. For the wind induced fatigue damage calculation, a dynamic wind spectral fatigue analysis was performed. First, a dynamic natural frequency analysis was performed to generate the structural dynamic characteristics, including the eigenvalues (natural frequencies), eigenvectors (mode shapes), and mass matrix. To adequately represent the dynamic characteristic of the structure, the number of modes was appropriately determined in the lateral direction. Second, a wind spectral fatigue analysis was performed using the mode shapes and mass data obtained from the previous results. In this analysis, the Weibull distribution of the wind speed occurrence, occurrence probability in each direction, damping coefficient, S-N curves, and SCF of each joint were defined and used. In particular, the wind fatigue damages were calculated under the assumption that the stress ranges followed a Rayleigh distribution. The total fatigue damages were calculated from the combination with wind and wave fatigue damages according to the DNV rule.