• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.8 s.239
• /
• pp.1085-1092
• /
• 2005

The OHT(Over Head Transportation) Vehicle transports heavy products quickly and repeatedly at the industrial workplace. The belt in the OHT vehicle is used to support the weight of the OHT Cage. The fatigue of the belt is caused by the dynamic load during the operation time. Since the fatigue fracture of the belt affects the safety at the workplace, the correct prediction of the dynamic load is necessary to calculate the fatigue life of the belt on the design step. In this paper a computer aided analysis method is proposed for the belt in the early design stage using dynamic analysis, stress analysis, belt tensile test, belt fatigue test and fatigue lift prediction method. From the dynamic load time histories and the stress of the belt FE model, a dynamic stress time history is produced. Using linear damage law and cycle counting method, fatigue life cycle is calculated. The method developed in this paper is used to reduce the time and cost for designing the OHT belt in different environment and condition.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.89-94
• /
• 2002

A commercial CFD code is used to calculate the 3-D viscous flow field within the centrifugal pump impeller. Design conditions are changed by impeller inlet(9.3mm, 12.2mm) and outlet breadth(6.65mm, 6.85mm). Numerical calculation was performed by changing flow rate from 8 to 26m$^{3}$/hr. Computation results shows that total head is increased at the larger inlet and outlet breadth than the others. And when the flow rate is increasing, the total head was decreased. The maximum efficiency of pump is shown at the design flow rate(16m$^{3}$/hr). In this study shows that the calculated results are good agreements with analysis results of design condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.189-194
• /
• 2004

As a disk drive becomes widely used in portable environments, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes In contact with outer shock disturbance, the system gets critical damage in head-gimbal assembly or disk. This paper describes analysis of a HGA(head-gimbal assembly) in micro MO drives to shock loading during both non-operating state and operating state. A finite element model which consists of the disk, suspension, slider and air bearing was used to find structural response of micro MO drives. In the operational case. the air bearing is approximated with four linear elastic springs. The commercially available finite element solver, ANSYS/LS-DYNA, is used to simulate the shock response of the HGA in micro MO drives. In this paper, the mechanical robustness of the suspension is simuiated considering the shock responses of the HGA.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.138-143
• /
• 2000

This paper addresses experimental results carried out to investigate the transmission of seat vibration to the head for Korean. Vertical seat vibration in the frequency range of 0.5-30 Hz was applied to a seated Korean male subject. To examine the intra-variable effects on transmissibility, five different postures and three different vibration excitation levels were considered. The applied acceleration and head accelerations of the seated subject were measured simultaneously by using a 6-axes bite-bar. Detailed experimental results of measured transmissibilities are illustrated for each posture and/or vibration excitation level. They are found to allow the identification of dynamic characteristics of Korean seated body for various real vibration environments. Furthermore, they are expected to be very useful in designing new seats for automotive and railway vehicles and in improving their vibration ride quality.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.89-95
• /
• 1999

In this study, the corrosion resistance of the aluminum casting commercial materials used in the automotive engine parts with respect to the anti-freeze coolant environment has been tested by the potentio dynamic method. especially, the effect of borax additive in engine coolant on the corrosion resistance of the aluminum casting materials has been evaluated. It was found that the borax in commercial engine coolant, used to prevent the corrosion in cast iron engine, causes a pit corrosion of aluminum casting materials at high temperature. During the engine endurance test with the coolant containing borax, the aluminum cylinder head was failed by the pitting corrosion near the exhaust port. Conclusively, it was suggested that the use of borax in the anti-freeze coolant be restricted for the automotive with aluminum cylinder head.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.5
• /
• pp.263-266
• /
• 2006

An optical microphone was developed using a dual-core multi-mode fiber block and a membrane type micromirror. The fiber block serves as a compact optical head, and the micromirror as a reflective diaphragm. The micromirror is designed to be suspended through a silicon bar connected t a frame, allowing for displacement induced by acoustic waves. The optical head is implemented by integrating two multi-mode fibers in a single block, and used to transfer light signals between it and the diaphragm. For the assembled microphone, its static characteristics were observed to reveal the operating point defined as the optimum distance between the optical head and the diaphragm. And its dynamic response was tested to exhibit a frequency bandwidth of 3 kHz with the variation of $\sim5dB$.

• Journal of Veterinary Science
• /
• v.21 no.4
• /
• pp.62.1-62.7
• /
• 2020

A 5-month old Shih Tzu was diagnosed with congenital elbow luxation and uniapical complex angular deformity of the radius. Single radial oblique and dynamic ulnar osteotomies were performed, using patient-specific 3D-printed osteotomy guide. External skeletal fixation was maintained for three weeks to prevent re-luxation of elbow joint. Three months after the surgery, objective gait analysis indicated markedly improved limb function. In addition, radiograph showed improved congruity of elbow joint and appropriate bone healing. In dogs with congenital radial head luxation and concurrent complex angular deformity, a single oblique osteotomy might be a viable option to preserve bone length and correct the luxation of elbow joint.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.440-445
• /
• 2011

Dynamic characteristic analysis is required in developing SMT mounter system with high installation speed and position precision, because of vibration source occurred by positioning head. This paper presents the method of improving dynamic characteristic of SMT(Surface Mount Technology) mounter with finite element method and modal test. The design direction is that natural frequencies of SMT mounter must be higher than the vibration source. In addition, the effect of input shaping on residual vibration reduction is investigated by simulating the response of a first-order system.

• Structural Engineering and Mechanics
• /
• v.53 no.2
• /
• pp.297-309
• /
• 2015

The purpose of this work is to analyze the effect of structure parameter disturbance on the dynamic characteristics of a hydropower station powerhouse. A vibration model with a head-cover system is established, and then the general disturbance problem analysis methods are discussed. Two new formulae based on two types of disturbances are developed from existing methods. The correctness and feasibility of these two formulae are validated by analyzing the hydropower station powerhouse vibration model. The appropriate calculation method for disturbance of the hydropower station powerhouse vibration dynamic characteristics is derived.

• The Journal of Korean Physical Therapy
• /
• v.21 no.4
• /
• pp.43-49
• /
• 2009

Purpose: This study examined the dynamic peak plantar pressure under the foot areas in those with a functional leg length inequality. Methods: The dynamic peak plantar pressure under the foot areas in an experimental group with a functional leg length inequality (n=20) and a control group (n=20) was assessed a using the Mat-Scan system (Tekscan, USA). The peak plantar pressure under the hallux, 1st, 2nd, 3-4th and 5th metatarsal head (MTH), mid foot, and heel was measured while the subject was walking on the Mat-Scan system. Results: The experimental group had significantly higher peak plantar pressure under all foot areas when the dynamic peak plantar pressure in the short leg and long leg sides was compared. The control group had a significantly higher peak plantar pressure under the 1st, 2nd, 3-4th, and 5th MTH when the dynamic peak plantar pressure in the short leg and long leg sides were compared. The experimental group showed a significantly larger difference in the dynamic peak plantar pressure under the hallux, 1st, 2nd, 3-4th and 5th MTH, mid foot and heel than the control group. Conclusion: A functional leg length inequality leads to an increase in the weight distribution and dynamic peak plantar pressure in the side of the short leg.