• Journal of Life Science
• /
• v.33 no.7
• /
• pp.549-554
• /
• 2023

Korean ginseng has been used for centuries in traditional Chinese medicine as an overall wellness supplement. Red ginseng (Ginseng Radix Rubra) is produced by steaming the roots, followed by drying. Soft red ginseng is produced using a new processing technology. This study investigated whether soft red ginseng differs from raw and hard red ginseng in its physicochemical composition. Results showed that the total phenol content of raw ginseng was 2.96 mg/g at 80℃ and 3.47 mg/g at 160 ℃. Meanwhile, the total phenols of hard and soft red ginseng were 4.12 mg/g and 4.18 mg/g at 160℃, respectively. The total phenol contents of raw, hard red, and soft red ginseng revealed a statistically significant difference (p>0.05). The total flavonoid contents of raw, hard red, and soft red ginseng were 2.62 mg/g, 3.97 mg/g, and 3.83 mg/g at 160℃, respectively. Among the three samples, soft red ginseng had the highest total sugar content at 160℃. The acidic polysaccharide contents of both soft and hard red ginseng were much higher than that of raw ginseng (49%-58%). Significant differences were observed among raw, hard red, and soft red ginseng (p<0.001). Soft red ginseng exhibited higher phenol content (25%), total flavonoid content (49%), and total sugar content (45%) than raw ginseng.

• Textile Coloration and Finishing
• /
• v.35 no.4
• /
• pp.196-205
• /
• 2023

Water-dispersed pigment is on-going study for without air pollution in the textile and print industry. Primer treatment is essential for the substrate to improve the printing quality of eco-friendly water-dispersed pigment ink. Otherwise in the case of untreated primer, the water-dispersed pigment ink will dry onto the surface and cause defective images. This study was conducted on film substrate coating (primer) to fix eco-friendly water-dispersed pigment ink on film substrate. The drying, bleeding, and color strength of the pigment ink were examined depending on the composition and mixing ratio of the coating solution. The mixing ratio of silica gel in the coating film is increased to 0, 0.5, 1, 2 and 3 and results that DK-1-3 of silica gel ratio of 1 showed the lowest bleeding such as 52%, the letter thickness of 0.76mm and DK-1-5 of SG ratio of 3 showed the highest bleeding such as 304%, the letter thickness of 2.02mm. The mixing ratio of SPA in the coating film is increased to 2.5, 5, 7.5, SPA ratio of 7.5 has a bleeding ratio of 9% and letter thickness of 0.544mm. It showed the closest value to 0.5mm. According to the result, the optimal mixing ratio of binder, polymer coagulant, silica gel is 100:7.5:1.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.1007-1016
• /
• 2023

In this study, the effect of functional substances such as polyphenols and flavonoids contained in large quantities in red ginseng and herbal medicines on the antioxidant activity properties and flavor effect were investigated by increasing the content and activity of functional ingredients by convert red ginseng through a steaming heat-drying process compared to the traditional dry processing method of ginseng and herbal medicines. According to the experimental results, the addition of pre-heat treatment significantly increased antioxidant properties such as DPPH radical scavenging ability, polyphenols, and flavonoids. In addition, during the steaming and heat-dried red ginseng manufacturing process, the amino-carbonyl browning reaction was promoted, resulting in increased brownness and a savory flavor. However, the content of ginsenosides, the main medicinal ingredient in red ginseng, became the main cause of the bitter and harsh taste. In addition, the bitter and harsh taste of red ginseng has been significantly improved by roasting and producing powder, but on the other hand, Radix Angelicae sinensis, polymorphic angelica and Peony, which are used as main medicinal ingredients in oriental medicine for nutritional tonic prescriptions such as 10 herbal medicine and 4 herbal medicine have a very strong herbal medicine-specific flavor and have a bitter and harsh taste. It is so strong that in order to use it as an instant extraction material, it was reviewed that a steaming and heating manufacturing method was needed during the manufacturing process.

• Food Science and Preservation
• /
• v.30 no.6
• /
• pp.983-990
• /
• 2023

This study was conducted to develop a preservation technology that can induce changes in physicochemical properties to effectively utilize of persimmon leaves. The application effects of steaming or freezing technique were investigated. Astringent persimmon leaves were steam-blanched (100℃, 30 sec) or frozen (-20℃, 15 d), followed by hot-air drying (50℃). The physicochemical properties of the extract obtained by hot-water leaching from the dried leaves were compared. The extract of leaves dried without pretreatment was used as a control. L* value was higher in steamed than in control and frozen. a* value was highest in the control. The browning index was higher in the frozen and lower in the steamed than in the control. Soluble solids were the highest in the steamed and the lowest in the frozen. Sucrose content was relatively high in the steamed, and the glucose and fructose contents were relatively high in the frozen. Total polyphenol content and DPPH radical scavenging activity were higher in steamed and lower in frozen than in control. Thus, it was confirmed that steam or freeze pretreatment after harvesting persimmon leaves affects the extraction yield, color, antioxidant capacity and component changes of dried persimmon leaves. Unlike steaming, freezing pretreatment showed the effect of promoting decomposition and browning reactions, and it is considered useful when such an effect is needed.

• Korean Journal of Agricultural Science
• /
• v.10 no.2
• /
• pp.249-256
• /
• 1983

The aspect of flowering was investigated in 'Georgia' cut lilies which had four flowers per stem. Concurrently effects of preservative solutions on longevity, petal length, water uptake and fresh weight of cut flowers were examined. 1. Days of opening of the 1st, 2nd and 3rd flower were 1-2 days, 3-4 days and 5-6days after beginning of holding treatment respectively. But the 4th flower was opened 9-10 days after beginning of holding treatment when the 1st and 2nd flowers were wilting or drying. 2. The later the opening of flower in a stem was, the shorter the longevity of flower became. But the effects of preservative solutions on longevity were gradually increased as the opening of flower was late in a stem. 3. Preservative solutions containing sucrose and $AgNO_3$ or HQ were able to increase petal length and longevity of the 3rd and 4th flowers sufficiently like the 1st and 2nd flowers. 4. Petal length, water uptake, fresh weight and longevity of cut lilies held in preservative solution containing sucrose, $AgNO_3$ and HQ were increased significantly compared with others. Solution containing sucrose alone increased longevity but decreased water uptake remarkably and did not increase fresh weight and petal length effectively compared with the control.

• Journal of Conservation Science
• /
• v.30 no.3
• /
• pp.263-275
• /
• 2014

It's shown how to proceed the study on Manufacturing techniques & Conservation to the Iron Pot from Cheonmachong Ancient Tomb(the 155th Tomb in Hwangnam-dong). In order to investigate manufacturing techniques of the Iron Pot, some parts of the relic were gathered. After mounting, polishing and etching on the relic, analyzing the metal microstructure was conducted. Also it's conducted a SEM-EDS analysis on the nonmetallic inclusion. White iron structure was observed in the metallurgical structure inspection, SEM-EDS analysis. It seems to be dried slowly at room temperature after casting, doesn't look as particular heat treatment to improve brittleness. It is estimated that it's as the handle seam side were verified about 3cm inch wide, 1.5 thick in center of body, so 2 separate half-completed products was cast with width-type mould. The manufacturing techniques Using white cast iron structure, width-type mould are observable to the Iron Pot excavated from Sikrichong Ancient Tomb & Hwangnamdaechong grand Ancient Tomb around those were constructed the same time. It's able to recognize that it's almost identical manufacturing techniques at that time. Conservation is generically following those are survey of pretreatment, foreign material removal, stabilization, restoration and color matching in the order. cleaning & drying were added to the process as occasion demands. The strengthening treatment were difficult with artifact's volume, low concentration Paraloid NAD-10 solution was spread two or three times with a brush, surface hardening also came up with 15wt% Paraloid NAD-10 solution after the conservation was complete. There were connection & restoration for the restoration to the damage after modeling forms that it's similar to damaged parts by using the Fiber Reinforced Plastic resins(POLYCOAT FH-245, mold laminated type). Throughout this research, capitalizing on accumulations of measurements about the production technique of Iron Pot in the time of the fifth and 6th centuries is no less important than the Iron artifact's conservation for a better study in the future.

• Journal of Mushroom
• /
• v.18 no.4
• /
• pp.344-356
• /
• 2020

This study aimed to investigate the biological activities and amino acid content in the mixtures of roasted edible mushrooms (Pleurotus ostreatus, and Lentinula edodes) and grain additives (oat and brown rice) obtained under different extraction conditions for the development of mushroom tea. The total amount of polyphenol and β-glucan in edible mushrooms was increased with the roasting treatment compared to that observed with the air-drying treatment. In addition, DPPH radical scavenging activity and the amount of all amino acid components, including glutamic acid (Glu), were higher in the oat extracts than those observed in the brown rice. The biological activities and nutrient content were examined based on extraction temperatures and thetime required to obtain the mixtures of edible mushrooms and grain additives. The extract of a 1:1 mixture of L. edodes + oat (LE+O) obtained at 100℃, 3 min showed high DPPH radical scavenging activity (33.5%), and the extract of 3:1 mixture of P. ostreatus + brown rice (PO+B) obtained at 100℃, 3 min showed high nitrite scavenging activity (49.9%). The total polyphenol content of the extract of 3:1 mixture of P. ostreatus + brown rice (PO+B) was the highest when obtained at 16.2 mg GAE/g and+ brown rice (PO+B) was the highest when obtained at 16.2 mg GAE/g and 70℃, 10 min. The essential amino acid content was higher in the 1:1 mixing ratio of P. ostreatus + oat (PO+O) and P. ostreatus + brown rice (PO+B) and 3:1 mixing ratio. L. edodes + oat (LE+O) and L. edodes + brown rice (LE+B) compared to that observed in other mixing ratios.

• Economic and Environmental Geology
• /
• v.54 no.6
• /
• pp.709-716
• /
• 2021

In this study, an adsorbent prepared by natural drying of iron hydroxide-based sludge collected from settling basin at a mine drainage treatment facility located in Gangneung, Gangwon-do was used to remove fluoride in an artificial fluoride solution and mine drainage, and the adsorption characteristics of the adsorbent were investigated. As a result of analyzing the chemical composition, mineralogical properties, and specific surface area of the adsorbent used in the experiment, iron oxide (Fe₂O₃) occupies 79.2 wt.% as the main constituent, and a peak related to calcite (CaCO₃) in the crystal structure analysis was analyzed. It was also identified that an irregular surface and a specific surface area of 216.78 m²·g^-1. In the indoor batch-type experiment, the effect of changes in reaction time, pH, initial fluoride concentration and temperature on the change in adsorption amount was analyzed. The adsorption of fluoride showed an adsorption amount of 3.85 mg·g^-1 16 hours after the start of the reaction, and the increase rate of the adsorption amount gradually decreased. Also, as the pH increased, the amount of fluoride adsorption decreased, and in particular, the amount of fluoride adsorption decreased rapidly around pH 5.5, the point of zero charge at which the surface charge of the adsorbent changes. Meanwhile, the results of the isotherm adsorption experiment were applied to the Langmuir and Freundlich isotherm adsorption models to infer the fluoride adsorption mechanism of the used adsorbent. To understand the thermodynamic properties of the adsorbent using the Van't Hoff equation, thermodynamic constants 𝚫H° and 𝚫G° were calculated using the adsorption amount information obtained by increasing the temperature from 25℃ to 65℃ to determine the adsorption characteristics of the adsorbent. Finally, the adsorbent was applied to the mine drainage having a fluoride concentration of about 12.8 mg·L^-1, and the fluoride removal rate was about 50%.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.15 no.3
• /
• pp.3059-3088
• /
• 1973

The Object of research was laid on the dry paddy field which had a low level of underground water, rather than on a paddy field with a high level of underground water. In the treatment of the clay paddy field before transplanting we employed 3 kinds of methods; deep plowing, development of cracks by drying the surface of the field under which pipe drain was built. This study was to find which one, among these three methods, is the most effective to let roots extend to deep zone and increase the yield of rice and at the same time, for trafficability of large scale machinery which will be introduced to the harvest, in the light of the earth bearing capacity in relation with underground drainage. In the treatments of plots, 1) the kyong plot was plowed 39 days before transplanting and dried, 2) the kyun plot was plowed again 2days before transplanting after plowing 39 days before transplanting, leveling field surface in the saturation with water and developing the cracks by drying, 3) the kyunam plot was plowed again 2 days before transplanting after setting the drainage pipe and at the same time plowing 39 days before transplanting, leveling field surface in the saturation with water and developing the cracks by drying. Also each plot above had three different levels of soil depth, respectively; that is 15cm, 25cm, 35cm. The kyong plot with 15cm-depth was he control. The results obtained were as follows; 1. The kyunam plot showed a remarkably lager amount of water consumption by better underground drainage than the kyong and the kyun plot, and the kyong plot indicated a greater amount of water consumption than the kyun plot. Therefore the amount of available rainfall was decreased in the order of kyunam>kyong>kyun. The net duty of water decreased in the order of kyunam>kyong>kyun and its showed about 105cm in depth at the kyunam plot, about 70cm in depth at the kyong plot and about 45cm in depth at kyun plot, regardless of soil depth. 2. According to the tendency that the weight of the total root was effected by the maximum depth of the crack, it seemed that the root development was more affected by the depth of the crack than by only the crack itself. The weight of the total roots tended to increase as the depth of the crack got deeper and deeper, and the weight of the total roots was increased in the order of kyun<kyunam<kyong. 3. In the growing of the plant height, the difference did not appear at the beginning of growing(peak period of tillering) of any plot, But for the mid period of growing(ending period of tillering) to the period of young panicle formation, the deeper the depth of plot is, the more the growing goes down. On the contrary at the late period of growing, growth was more vigorous in the plot with deep depth than in the plot with shallow depth. Since the midperiod of growing, in the light of experimental treatment, the kyun plot was not better in growing than the other two plots and no remarkable defference was shown between the kyunam and the kyong plot, but the kyunam plot had the tendency of superiority in growing plant height. 4. As the depth of plot went deeper, the decreasing tendency was shown in the number of tillers through a whole period of growingi. When the above results were observed concering each plot of experimental treatment, the kyun plot was always smaller in the number of tiilers than the kyunam and the kvong plot, and the kyong plot was slightly larger than the kyunam plot in the number of tillers. 5. When each plot of the different experimental treatments was compared with the control plot(15-kyong), yield(weight of grains) was increased by 17% for the 35-kyong plot, by 10% for the 35-kyunam and yields for the other plots were less or nomore than the control plot. On the whole, as the depth of plot went deeper, yields for plots was increased in the order of kyong>kyunam>kyun. 1% of significance between the levels of depths and 5% of significance between the treatments were shown. 6. The depth of consumptive water which was more effective on the weight of grains is that of the last half period. When the depth of consumptive water was increased at the range of less than 2.7cm/day in the 15cm plot, 3.0cm/day in the 25cm plot and 3.3cm/day in the 35cm plot, the weight of grains was increased, and at the same time the weight of grains was increased as the depth of plot went deeper. The deeper plots was of advantage to the productivity at the same depth of consumptive water. 7. The increase in the weight of grains in propertion to the weighte of root showed a tendency to increase depending on the depth of plot at each plot of the same weight of roots. The weight of roots and grains together increasezd in the order of kyun>kyunam>kyong, considering each treatment of experimental plot. The weight of grains was in relation to the minimum water content ratio during the midperiod of surface drainage and the average earth temperature was mainly affected by the minimum water content ratio because it was relatively increased in proportion to the water content ratio(at less than 40%) 8. The weight ratio of straw to grain showed an increasing tendency at the plot of shallow depth and had a relation of an inversely exponental function to the weight of roots. At the same depth of plot except the 15cm plot, the weight ratio of straw to grain was increased in proportion to the depth of consumptive water. The weight of grains was increased as the depth of consumptive water was increased to some extent, but at the same time the weight of ratio of straw to grain was increased. 9. At a certain texture of soils the increase in the amount of the cracks depends on meteorological conditions, especially increase in amounts of pan evaporation. So if it rains during the progressing of field drying the cracks largely decrease. The amount of cracks of clay soil had relation of inversely exponental function to the water content ratio(at more than 25%). The maximum depth of crack kept generally a constant value at less than 30% of water content ratio. 10. The cone index showed the tendency that it was propertional to the amount of cracks within a certain limit but more or less inversely proportional over a certain limit. The water content ratio at the limit may be about 25%. 11. The increase in the cone index with the progressing of time after final surface drainage showed the tendency that it was proportional to the depth of consumptive water at the last half of growing period. Based on the same depth of if the cone index in the kyunam plot was much larger than in the other two plots and that in the kyong plot was much smaller than in the kyun plott, as long as the depth of plot was deeper, especially in the 35-kyong plot. 12. In the light of a situation where water content ratio of soil decreased and the cone index increased after final surface drainage the porogress of the field dryness was much more rapid in the kyunam plot than in the kyong plot and the kyun plot, especially slowest in the kyong plot. In the plot with deeper zone the progress was much slower. The progress requiring the value of the cone index, $2.5kg/cm^2$, that working machinary can move easily on the field changed with the time of final surface drainage and the amount of rainfall, but without nay rain it required, in the kyunam plot, about 44mm in total amount of pan evaporation and more than 50mm in the other two plots. Therefore the drying in the kyunam plot was generally more rapid in the kyunam plot was generally more rapid over 2days than in the kyun plot, and especially may be more rapid over 5days than in the 35-kyong plot.

• Journal of Sericultural and Entomological Science
• /
• v.16 no.1
• /
• pp.21-48
• /
• 1974

The studies were carried out to disclose the physical and chemical properties of sericin fraction obtained from silk cocoon shells and its characteristics of swelling and solubility. The following results were obtained. 1. The physical and chemical properties of sericin fraction. 1) In contrast to the easy water soluble sericin, the hard soluble sericin contains fewer amino acids include of polar side radical while the hard soluble amino acid sach as alanine and leucine were detected. 2) The easy soluble amino acids were found mainly on the outer part of the fibroin, but the hard soluble amino acids were located in the near parts to the fibroin. 3) The swelling and solubility of the sericin could be hardly assayed by the analysis of the amino acid composition, and could be considered to tee closely related to the compound of the sericin crystal and secondary structure. 4) The X-ray patterns of the cocoon filament were ring shape, but they disappeared by the degumming treatment. 5) The sericin of tussah silkworm (A. pernyi), showed stronger circular patterns in the meridian than the regular silkworm (Bombyx mori). 6) There was no pattern difference between Fraction A and B. 7) X-ray diffraction patterns of the Sericin 1, ll and 111 were similar except interference of 8.85A (side chain spacing). 8) The amino acids above 150 in molecular weight such as Cys. Tyr. Phe. His. and Arg. were not found quantitatively by the 60 minutes-hydrolysis (6N-HCI). 9) The X-ray Pattern of 4.6A had a tendency to disappear with hot-water, ether, and alcohol treatment. 10) The partial hydrolysis of sericin showed a cirucular interference (2A) on the meridian. 11) The sericin pellet after hydrolysis was considered to be peptides composed with specific amino acids. 12) The decomposing temperature of Sericin 111 was higher than that of Sericin I and II. 13) Thermogram of the inner portioned sericin of the cocoon shell had double endothermic peaks at 165$^{\circ}C$, and 245$^{\circ}C$, and its decomposing temperature was higher than that of other portioned sericin. 14) The infrared spectroscopic properties among sericin I, II, III and sericin extracted from each layer portion of the cocoon shell were similar. II. The characteristics of seriein swelling and solubility related with silk processing. 1) Fifteen minutes was required to dehydrate the free moisture of cocoon shells with centrifugal force controlled at 13${\times}$10$^4$ dyne/g at 3,000 R.P.M. B) It took 30 minutes for the sericin to show positive reaction with the Folin-Ciocaltue reagent at room temperature. 3) The measurable wave length of the visible radiation was 500-750m${\mu}$, and the highest absorbance was observed at the wave length of 650m${\mu}$. 4) The colorimetric analysis should be conducted at 650mu for low concentration (10$\mu\textrm{g}$/$m\ell$), and at 500m${\mu}$ for the higher concentration to obtain an exact analysis. 5) The absorbing curves of sericin and egg albumin at different wave lengths were similar, but the absorbance of the former was slightly higher than that of the latter. 6) The quantity of the sericin measured by the colorimetric analysis, turned out to be less than by the Kjeldahl method. 7) Both temperature and duration in the cocoon cooking process has much effect on the swelling and solubility of the cocoon shells, but the temperature was more influential than the duration of the treatment. 8) The factorial relation between the temperature and the duration of treatment of the cocoon cooking to check for siricin swelling and solubility showed that the treatment duration should be gradually increased to reach optimum swelling and solubility of sericin with low temperature(70$^{\circ}C$) . High temperature, however, showed more sharp increase. 9) The more increased temperature in the drying of fresh cocoons, the less the sericin swelling and solubility were obtained. 10) In a specific cooking duration, the heavier the cocoon shell is, the less the swelling and solubility were obtained. 11) It was considered that there are differences in swelling or solubility between the filaments of each cocoon layer. 12) Sericin swelling or solubility in the cocoon filament was decreased by the wax extraction.. 13) The ionic surface active agent accelerated the swelling and solubility of the sericin at the range of pH 6-7. 14) In the same conditions as above, the cation agent was absorbed into the sericin. 15) In case of the increase of Ca ang Mg in the reeling water, its pH value drifted toward the acidity. 16) A buffering action was observed between the sericin and the water hardness constituents in the reeling water. 17) The effect of calcium on the swelling and solubility of the sericin was more moderate than that of magnecium. 18) The solute of the water hardness constituents increased the electric conductivity in the reeling water.