• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.55-66
• /
• 2012

To investigate the hysteresis of the suction stress in unsaturated weathered mudstone soils (CL), matric suction and volumetric water content were measured in both drying and wetting processes using Automated Soil-Water Characteristics Curve Apparatus. The drying and wetting processes in unsaturated soils were reproduced in the test; the drying process means to load matric suction to spill pore water from the soils, and the wetting process means to unload matric suction to inject pore water into the soils. Based on the measured result, Soil Water Characteristic Curve(SWCC)s were estimated by van Genuchten model (1980). SWCCs have nonlinear relationship between effective degree of saturation and matric suction. The hysteresis in SWCCs between drying and wetting processes occurred. As a result of estimating Suction Stress Characteristic Curve(SSCC) using Lu and Likos model (2006), the suction stress rapidly increased in the low level of matric suction and then increased slightly. Also, the hysteresis in SSCCs between drying and wetting processes occurred. In order to design geo-structures and check its stability considering unsaturated soil mechanics, therefore, it is more reasonable that the SSCC of drying process should be applied in the condition of rainfall infiltration and the SSCC of wetting process in the condition of evaporation or drainage.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.192-199
• /
• 2009

This study was carried out to investigate the performance of a radio-frequency/vacuum dryer combined with a mechanical compressive load (RF/VC) with a scale of about $3m^3$ during drying board of Azobe (Lophira alata) and Korean red pine (Pinus densiflora). The degree of vacuum of the RF/VC system was maintained at 80~105 torr, and wood temperature was increased from $40^{\circ}C$ at the beginning of drying to $60^{\circ}C$ at the end of drying and the radiofrequency generator was operated with schedule of 7 minute-ON and 3 minute-OFF. The wood temperatures near charge plate always remained higher than those of the control during all of the drying stage, whereas the wood temperature near ground plate always remained lower than those of the controlled. As drying time proceeding, the temperature of the wood near ground plate presented lower than those of the control. Whereas the temperature of the wood near charge plate presented higher than those of the controlled. The final average moisture contents of the Azobe boards stacked near the input side of the RF generator showed slightly lower than those near the opposite side. Those of the wood stacked in the layers near the charge plate were lower than those of near the ground plate. The average length of surface checks of the Azobe boards stacked near the charge plate was very slight, whereas that toward the ground plate represented high values. The efficiency of input energy was simliar with the commercial systems.

• Korean Journal of Food Science and Technology
• /
• v.27 no.3
• /
• pp.394-403
• /
• 1995

Various thermal treatments such as toasting, roasting, drum drying, autoclaving+drum drying, microwaving+drum drying and extrusion were attempted to investigate their effects on chemical composition (proximate composition, Klason lignin, neutral sugar, uronic acid, starch, free sugar, dietary fiber, phytic acid, etc) and functional properties (water solubility index, water absorption index, water holding capacity, oil holding capacity, bulk density, swelling, etc) of wheat bran. Thermal treatments on wheat bran increased soluble dietary fiber (SDF) content from 2.7% (raw sample) to 4.6% (toasted), 4.5% (roasted), 4.6% (drum dried), 5.2% (autoclaved), 3.7% (microwaved), 5.6% (extruded). In contrast, total dietary fiber (TDF) content remained nearly constant regardless of thermal treatments, reflecting the concomitant decrease in insoluble dietary fiber (IDF). It was also found that water holding capacity (WHC) increased $20{\sim}75%$ due to thermal treatments employed in this research. Both bulk density and swelling were not directly relevant to WHC, but thier multiplication exhibited good correlation $(R^2=0.94)$ with WHC. Scanning elctron microscopy (SEM) exhibited that structure of raw wheat bran was significantly modified, whose degree and shape well reflected the types of thermal treatments.

• Computers and Concrete
• /
• v.13 no.3
• /
• pp.361-375
• /
• 2014

The moisture transport in underground concrete was experimentally investigated and the nonlinear model of moisture transport considering the effects of water diffusion, hydration of cementicious materials and water permeability was proposed. The consumed moisture content by self-desiccation could be firstly calculated according to evolved hydration degree of cement and mineral admixtures. Furthermore, the finite differential method was adopted to solve the moisture transport model by linearizing the nonlinear moisture diffusion coefficient. The comparison between experimental and calculated results showed a good agreement, which indicated that the proposed moisture model could be used to predict moisture content evolution in underground concrete members with drying-wetting boundaries.

• Journal of Nutrition and Health
• /
• v.13 no.3
• /
• pp.145-149
• /
• 1980

To study the rancidity of dried yellow carlbina oil by oxidation during the storage period general properties of the oil and composition of its fatty acid were analysed quantitatively with gas chromatography The results indicated that I) The dried yellow carbina oil was involved in drying oil of high degree of unsaturation with IV 138 and consisted of higher-fatty acid with SV 194. 2) The composition of the fatty acids were composed of 18 fatty acids involving 6 unknown fatty acids and comprised poly-unsaturated fatty acid with $C_{18}^{:3}\:and\:C_{22}^{:5}$ 3) After three morths storage of dried yellow carbina the content of malonaldehyde was about 12mg/kg in its exterior part, but 6mg/kg in interior part, which indicateing that the degree of rancidity of poly unsaturated glycerides in exterior part of carbina were two times as much as that of interior part.

• Korean Journal of Plant Resources
• /
• v.18 no.3
• /
• pp.505-511
• /
• 2005

This study was carried out to obtain the basic information for quality changes according to degree of exposed sunlight after harvest of aerial part in Saururus chinensis Baill. Top part harvested was exposed to sunlight from 0 to 3 hours with 1-hour interval, and was dried at $50^{\circ}C$ hot air. The values were higher at shorter time of sunlight exposure, while the opposite is the true to the a values. The b and c values were high at 2-hour exposure before drying. Those were higher at shorter time of sunlight exposure after drying, but showed opposite tendency in tang-jeon. The contents of rutin and quercitrin, and astringency were greater at shorter time of sunlight exposure. Preference of quality and tang-jeon showed similar tendency with those.

• Applied Chemistry for Engineering
• /
• v.22 no.1
• /
• pp.81-86
• /
• 2011

The aqueous solution of Sunset Yellow-FCF (SY-FCF) began to show schlieren texture at room temperature when its concentration reaches 25 wt%. A further increase of the concentration of SY-FCF to 28 wt% resulted in a perfect nematic liquid crystal phase. However, more than 30 wt% of SY-FCF in aqueous solution was required to make an optically anisotropic film simply by shear coating. In our study, concentration of SY-FCF solution, coating speed, drying temperature, and relative humidity were considered as coating parameters affecting the preparation of optically anisotropic thin films. From analysis of variance analysis (ANOVA), the solution concentration was revealed as a main factor affecting the film thickness. The drying temperature and solution concentration were main factors affecting the transmittance of parallel direction ($T_o$). Especially, SY-FCF aqueous solution with high concentration induced a better alignment of LC columns and produced highly oriented anisotropic films. In this study, optically anisotropic films prepared by 33 wt% of SY-FCF in aqueous solution showed 89.7~98.7% of degree of polarization.

• Journal of Biomedical Engineering Research
• /
• v.34 no.3
• /
• pp.117-122
• /
• 2013

Hyaluronic acid(HA) microbeads were synthesized by dropping the sodium hyaluronate(Streptococcus) solutions in NaOH into a solution mixture of divinyl sulfone(DVS) in 2-methyl-1-propanol, followed by stirring, cleaning and drying process at room temperature. The initial experimental conditions are crosslinking time(CLTi) of 5 h, crosslinking temperature(CLTe) of room temperature, injection air pressure(IAPr) of 5 psi, and DVS concentration( DVSc) of 0.2 vol%, respectively. Then, parametric studies were performed by varying the parameters to investigate the morphology, the porosity, the swelling ratio and the size of the beads. The microbead size pattern was not regular to function of the degree of crosslink. It was observed that the swelling ratio, the degree of crosslink, and the pore size can be controlled by adjusting the CLTi, CLTe and DVSc. Among the parameters investigated, the smallest bead size can be achieved by varying the CLTi parameter. The lowest swelling ratio, as an indication of the highest degree of crosslink, can be obtained by varying CLTe.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.6
• /
• pp.547-553
• /
• 2015

For commercialization of fuel cell electric vehicles, one of the key objectives is to reduce cost of full stack assembly. Regarding Membrane Electrode Assembly, the major issue is to improve fuel cell activation process in the initial Hydrogen Oxidation Reaction and Oxygen Reduction Reaction. In this research, the VD (Vacuum Drying) process has been developed for improvement of activation process. The VD condition is developed by controlling the temperature and degree of vacuum to remove the remaining solvent of electrode. Consequently, the electrode applied to VD process showed the low characteristics such as 3.5% of remaining solvent content and the improved efficiency such as 15% of activation process speed.

• Fashion & Textile Research Journal
• /
• v.11 no.6
• /
• pp.947-952
• /
• 2009

The purpose of this study is to analyze skin wettedness($w$) used as the rate index of thermal comfort, and to evaluate the wear comfort of outdoorwear. Skin wettedness is widely used to express the degree of thermal comfort. If skin wettedness exceeds a certain threshold, the body feels damp and discomfort. An experiment which consisted of rest(30 min), exercise(30 min) and recovery(20 min) periods was administered in a climate chamber with 10 healthy male participants. Two kinds of outdoorwears made of 100% cotton fabrics (Control) and specially engineered fabrics having feature of quick sweat absorbency and high speed drying fabric (Functional) were evaluated in the experiment. The condition of climate chamber was controlled according to the thermal insulation of 4 kinds of experimental ensembles(E1~E4). Total sweat loss, sweat loss absorbed into clothing and skin temperature were measured. Skin wettedness was calculated from the ratio of evaporative rate to the maximal evaporative capacity. Skin wettedness of 'Functional' was lower than 'Control' in the 3 kinds of ensembles(E1, E2, E4) because the materials of 'Functional' were composed of quick sweat absorbency and high speed drying fabrics, water vapour permeability and waterproof fabrics.