• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.7
• /
• pp.975-980
• /
• 2001

The thermal analysis of the hot roller in a dry film laminator is studied numerically by steady-state two-dimensional heat transfer. In the laminating process for PDP glass or PCB, the temperature distributions in a hot roller are presented considering the effects of the roller rotation speed and the inner and outer radii of the roller. The results show that the temperature distributions are strongly dependent on Peclet number. If Pe number becomes larger, the iso-thermal lines are more concentric about the rotating axis and the temperature difference on the hot roller surface decreases exponentially. It also shows that if the contact angle between the roller and the film becomes smaller the temperature difference becomes smaller. However, the changes of the rollers inner or outer radius have little effect on the temperature difference.

• Journal of Environmental Science International
• /
• v.7 no.4
• /
• pp.559-564
• /
• 1998

The effects of temperature, initial $Pb^{2+}$concentration and initial sludge concentration on the initial $Pb^{2+}$ removal rate and maximal $Pb^{2+}$removal amounts in activated sludge, respectively, were investigated. The removal of $Pb^{2+}$ in activated sludge was proved to be temperature-dependent process. The initial $Pb^{2+}$ removal rate increased from 187.5 to 261.4 mg $Pb^{2+}$/g sludge dry weight min, in response to the promoted temperature from 1$0^{\circ}C$ to 6$0^{\circ}C$, while the maximal $Pb^{2+}$removal amount (78.5 mg $Pb^{2+}$/g sludge dry weight) occurred at 30t . As the initial $Pb^{2+}$concentration increased from 36 to 228 mg $Pb^{2+}$/L at the constant temperature of 30C and initial sludge concentration of 1.5 g sludge dry weight/L, the time to reach an equilibrium state was almost independent of the initial $Pb^{2+}$concentration and the equilibrium $Pb^{2+}$/removal amount was increased Irom 41.9 to 73.6 mg $Pb^{2+}$/g sludge dry weight. On the contrary, the equilbrium $Pb^{2+}$ emoval amount was decreased from 87.7 to 65.3 mg $Pb^{2+}$/g sludge dry weight as the in- crease of initial sludge concentration from 0.22 to 1.76 g sludge dry weight/L.

• Korean Journal of Microbiology
• /
• v.21 no.3
• /
• pp.163-169
• /
• 1983

Effects of temperature on the gorwth characteristics and the chemical composition of pseudomonas cells grown under glucose-or methanol-utilizing continuous culture were studied. In a glucose-utilizing continuous culture, optimum dilution rate, agitation, pH, and temperature, for the higher biomass yield were $0.45hr^-$, 7000rpm, pH 7.5, and $30^{\circ}C$, respectively. But in a methanol-utilizing continuous culture, they were $0.125hr^-$, 600rpm, pH 8, and $30^{\circ}C$, respectively. In methanol-utilizing continuous culture, the maximum production rate of the cells was 1.48g, dry wt./1/hr at a dilution rate of $0.45hr^-$, and the cell yield was 0.46g. dry wt./g. glucose. In the methanol-utilizaing continuous culture, the maximum production rate of the cells was 0.33 7g. dry wt./1/hr. at a dilution rate of $0.125hr^-$ and the cell yield was 0.44g dry cell/g. methanol. The contents of protein of the cells increase with the increase ingrowing temperature (from 15 to $30^{\circ}C$), more or less, while the contents of RNA nad carbohydrate of the cells decreased. However, DNA contents of cells growth under the various temperature ranges didn't change. As the temeprature of cultivation rises at a constant dilution rate, the efficiency of RNA in protein synthesis was increased, showing the decreases in the ratio of RNA to protein.

• KSBB Journal
• /
• v.14 no.5
• /
• pp.561-565
• /
• 1999

Optimum conditions for vacuum-drying ad cultivation of yeast cells for the production of active dry yeast were examined. At lower temperature, more drying time was required to dry the yeast pellet to reach the desirable water content(8%). Optimum temperature of vaccum oven and time for drying was 63$^{\circ}C$ and 90 min, respectively. Optimum medium composition for flask culture using cane molasses as the substrate were 0.25% sugar, 0.013% $K_2$HPO$_4$, 0.1% $K_2$HPO$_4$. and 0.125% (NH$_4$)$_2$SO$_4$. Culture temperature $25^{\circ}C$ gave the highest survival rate of dired yeast. After finishing fed-batch culture and the culture was left in the fermentor without adding any sugar or nutrient, survival of the dried yeast harvested from the fermentor increased to 86.0% after 36 hr. It was also observed that the yeast cells with higher budding rates showed lower survival rate.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.6
• /
• pp.524-531
• /
• 2001

The temperature and humidity distribution in a dry room are studied numerically by using standard$\kappa-\varepsilon$ turbulence model. In order to evaluate effective heat and moisture ventilation characteristics inside the room, the heat removal capacity and moisture exhaust efficiency are introduced. An effective ventilation control is analyzed by evaluating quantitatively temperature and humidity distributions. It was found that the mean absolute humidity inside the room was almost constant with approximately 0.1905g/kg air regardless of the models and the heat generation rates. This was believed that the moisture generation by workers was relatively small. 40% improvement of the critical decay time was achieved, through the modifications of design variables.

• Tunnel and Underground Space
• /
• v.7 no.2
• /
• pp.91-99
• /
• 1997

To stabilize the energy price, the more storage facilities of energy are required and among the storage methods of LPG and LNG, the method of storage at low temperature under normal confining pressure is considered. It is needed to understand the mechanical and thermal characteristics of rock under temperature variation so that the behaviors of rock can be predicted. In this paper, the variation of the rock charateristics of the Hwangdeung granite and the Boryung sandstone is studied at low temperature. The mechanical characteristics of rock under low temperatures are that as temperature decreased, unaxial compression strength and Young's modulus increased for Hwangdeung granite; strength and Young's modulus in wet condition were greater than those in dry condition. In the case of Boryung sandstone, as temperature decreases unaxial compression strength and Young's modulus increase but decrease below -10$0^{\circ}C$ in dry condition and below -16$0^{\circ}C$ in wet condtion. The mechanical characteristics of rock after cooling to previous temperature and thawing are that uniaxial compression strength and Young's modulus decrease as temperature decreases. Uniaxial compression strength and Young's modulus in wet conditon decrease more than those in dry condition. Brazilian tension strength decreases as temperature decreases.

• Journal of Animal Science and Technology
• /
• v.58 no.10
• /
• pp.36.1-36.5
• /
• 2016

Background: Liquid feeding system has been introduced to domestic swine farms, but negative cognition about liquid feeding system has been remained for feed waste decay related with poor management and microbial contamination. For these reasons, this study was conducted to evaluate the effects of feeding method in lactating sows. Methods: A total of 30 mixed-parity (average 4.13) lactating sows (Yorkshire ${\times}$ Landrace) with an initial BW of $218.8{\pm}19.5kg$ was used in a 3 week trial. Sows were allotted to 1 of 2 treatments in a completely randomized design by their body weight, backfat thickness, parity and alive litter weight. One of treatments was dry feeding and the other was liquid feeding (water to feed ratio, 1:1). Experimental diets contained 3265 kcal ME/kg, 12.6 % CP, 5.76 % EE, 1.09 % total lysine, 0.25 % total methionine, as fed basis. Results: Dry feeding treatment had high body weight loss rather than liquid feeding treatment (P = 0.04). Dry feeding treatment had tendency to increase litter weight at 21d of lactation (P = 0.06) and litter weight gain (P = 0.04) during lactation period (0-3 week). Sows fed dry feeding method made milk containing high content of casein and total solid rather than sows fed liquid feeding method (P = 0.04). In addition, dry feeding treatment had tendency to higher content of milk fat, protein and solid not fat on 21d of lactation (P = 0.07). Sows fed dry feeding type also showed higher milk energy content in milk of 21d lactation (P = 0.05). Furthermore, liquid feeding treatment showed high occurrence in feed waste during lactation period (P <0.01). Conclusion: Dry feeding method was more suitable feeding method to lactating sows under high temperature environment like lactating barn.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.394-397
• /
• 2004

This paper presents a simple analytic method using 2D simulation program for predications of cutting force and machining temperature in dry type milling process. And also, comparison of cutting force and machining temperature obtained from experiment and simulation work is accomplished to distinguish of suitability.

• Journal of Microbiology and Biotechnology
• /
• v.30 no.7
• /
• pp.1072-1081
• /
• 2020

Screening suitable strains with high temperature adaptability is of great importance for reducing the cost of temperature control in microalgae cultivation, especially in summer. To obtain high temperature-tolerant diatoms, water samples were collected in summer from 7 different regions of China across the Northeast, North and East. A total of 731 water samples was collected and from them 131 diatom strains were isolated and identified based on the 18S rRNA sequences. Forty-nine strains out of the 131 diatoms could survive at 30℃, and 6 strains with relatively high biomass and lipid content at high temperature were selected and were found to be able to grow at 35℃. Cyclotella sp. HB162 had the highest dry biomass of 0.46 g/l and relatively high triacylglycerol (TAG) content of 237.4 mg/g dry biomass. The highest TAG content of 246.4 mg/g dry biomass was obtained in Fistulifera sp. HB236, while Nitzschia palea HB170 had high dry biomass (0.33 g/l) but relatively low TAG content (105.9 mg/g dry biomass). N. palea HB170 and Fistulifera sp. HB236 presented relatively stable growth rates and lipid yields under fluctuating temperatures ranging from 28 to 35℃, while Cyclotella HB162 maintained high lipid yield at temperatures below 25℃. The percentage of saturated fatty acids and monounsaturated fatty acids in all the 6 strains was 84-91% in total lipids and 90-94% in TAGs, which makes them the ideal feedstock for biodiesel.

• Nuclear Engineering and Technology
• /
• v.36 no.4
• /
• pp.338-345
• /
• 2004

This study examines the sensitivity of several fabrication parameters for dry process fuel, using a random sampling technique. The in-pile performance of dry process fuel with irradiation was calculated by a modified ELESTRES code, which is the CANDU fuel performance code system. The performance of the fuel rod was then analyzed using a Monte Carlo simulation to obtain the uncertainty of the major outputs, such as the fuel centerline temperature, the fission gas pressure, and the plastic strain. It was proved by statistical analysis that for both the dry process fuel and the $UO_2$ fuel, pellet density is one of the most sensitive parameters, but as for the fission gas pressure, the density of the $UO_2$ fuel exhibits insensitive behavior compared to that of the dry process fuel. The grain size of the dry process fuel is insensitive to the fission gas pressure, while the grain size of the $UO_2$ fuel is correlative to the fission gas pressure. From the calculation with a typical CANDU reactor power envelop, the centerline temperature, fission gas pressure, and plastic strain of the dry process fuel are higher than those of the $UO_2$ fuel.