• Korean Journal of Agricultural Science
• /
• v.10 no.1
• /
• pp.97-109
• /
• 1983

In this study, the effects on the soil compaction were investigated through the various testing method by changing the number of layers, the number of blows per layer and drop height. The results obtained in this study were summarized as follows. 1. Soil compaction was largely influenced by maximum grain size of soil in case of small testing mold diameter. 2. The compaction effect showed best in the well graded soil. In this test, compaction effect showed the best value in the soil which contained about 30~40% of particles finer than No. 200 sieves although it would vary according to the content of coarse grained soil. 3. Though the compaction method was changed at the level of compaction energy fixed, the effect of soil compaction showed little. 4. The increment of compaction energy increased the effect of soil compaction, but over a certain limit the soil compaction showed little on the effect. 5. In the method to increase the compaction energy for the purpose of the most reasonable effect, the soil compaction effect was differently shown according to the grain size distribution of the soil.

• Particle and aerosol research
• /
• v.13 no.2
• /
• pp.79-85
• /
• 2017

This study identified the loss of minimum fluidization velocity and pressure in accordance with the superficial velocity of $NiO/MoO_3/MoS_2$, a rare metallic oxide and high value-added material in the lab-scale fluidized bed reactor (L=0.25 m, D=0.05 m). The average pressure loss in L/D 1, 2, and 3 of $NiO/MoO_3/MoS_2$ within the scope of superficial gas velocity between 0.07 and 0.45 m/s based on the L/D 1, 2, and 3 of the specimen was shown to be 290~1952 Pa at decreasing flux and 253~1925 Pa at increasing flux. The comparison between the theoretical value proposed by Wen and the test data showed a difference between 0.021~0.36 magnification. Based on these results, this study was able to determine the operation conditions where rare metallic oxides could be applied in real phenomena.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.47-47
• /
• 2011

국내의 기능성 난연성 섬유 제조기술은 원사 자체에 난연제가 포함된 상태인 난연 PET 원사나, 일반 PET 원단에 후방염 처리한 원단이 사용되기에 난연 방염성능이 만족스럽지 못하고 친환경적이지 못한 실정이다. 오늘날 세계 난연섬유 시장 규모는 10조원에 이르고 있으며 국내에서도 화재에 대한 경각심이 높아지는 추세이므로 기능성을 갖춘 고부가가치 난연소재의 개발이 시급하다. 폴리페닐렌술피드(PPS)는 내열성 및 내화학약품성이 뛰어난 열가소성 고분자로 용융방사가 가능하다. 난연성이 높은 양모섬유 또는 아크릴계 난연섬유, 아라미드 섬유 등은 비용 문제로 범용화에 한계가 있으므로 비교적 저렴한 PPS 섬유가 개발될 경우 범용화를 기대할 수 있다. 현재는 PPS 섬유가 특수한 용도에 주로 사용되고 있으나 우수한 난연 특성을 이용하여 일반 용도로의 사용 및 수요가 급격히 늘어날 것으로 예상되며 우선적으로 인테리어용 원단, 특히 커튼이나 소파용 원단으로 용도 전개가 가능할 것으로 판단하였다. 본 연구에서는 소파용 PPS 원단의 후가공 조건의 선정 및 불소계 발수방오가공을 위한 최적의 조건을 선정하고자 하였다. Padding(wet pick up율 $80{\pm}3%$)-Drying($105^{\circ}C$, 2.5min)-Curing은 시간은 1분으로 고정시킨 후, 온도를 150, 160, 170, 180, 190, $200^{\circ}C$에서 처리하여 Yellowness값을 측정한 결과, 온도가 높아질수록 Yellowness값이 커지는 것으로 미루어 보아 PPS원단은 높은 열에 영향을 받아 황변 현상이 일어나는 것으로 사료된다. 특히 $180^{\circ}C$를 기점으로 값에 큰 변화를 보였으므로 최적의 열처리 온도는 $170^{\circ}C$로 선정하여 이후의 실험을 진행하였다. 또한 큐어링 시간이 황변에 미치는 영향을 분석한 결과 온도에 의한 영향에 비해 적은 편으로 사료되었으나, 1.5min을 기점으로 Yellowess값이 높아졌으므로 최적의 열처리 시간을 1분으로 선정하였다. 최종 가공조건인 $170^{\circ}C$, 1분에서 처리한 시험포는 처리전 원단과 비교하였을 때, ${\Delta}$Yellowness가 2.84 정도로 나타났다. 그 후, PPS 원단에 불소가공제 (TG-991N, 동인텍스켐)의 적정 농도를 선정하기 위해 1~7%까지 농도를 높이며 처리한 결과, 불소가공제의 농도가 높아짐에 따라 황변현상이 나타남을 알 수 있었다. 농도가 높아짐에 따라 Yellowness값은 증가하다가 4% 이후 완만해지는 것을 알 수 있었으므로 IPA/Water Drop test와 발수도시험 (KS K 0590;2008)을 통해 적정 농도를 선정하였다. PPS 원단은 불소가공제의 농도가 높아짐에 따라 발수도가 우수해졌으며, 가공제 농도 3% 처리만으로도 우수한 발수도를 나타내었으나 100% 발수를 위해서는 가공제 농도가 5% 이상 처리되어야 하는 것을 확인할 수 있었다.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.6 no.4
• /
• pp.211-217
• /
• 2004

The instrument used in this study consists of a lkg capacity loadcell and a Imm tipping bucket rain gauge. There are two signals: one is the weight of the water in the tipping bucket and the other is the pulse from the reversing mechanism of the tipping bucket. The loadcell measures the weight of water with a 0.0lmm resolution up to 1mm rainfall and the bucket reverses beyond 1mm. From this point, a pulse signal generates and the loadcell starts measuring the weight again. A field test was carried out with the range of rainfall intensity from 42mm/h to 250mm/h. The result shows an error range from -2.2% to + 2.6% in 12 measurement cases with a rainfall of l00mm or more. This result satisfies the WMO recommendation for rainfall intensity instrumentation which allows a 5% range. In a field experiment during 17 to 19 August, 2004, more than 100mm/h rainfall intensity was observed by this instrument, confirming that our instrument has a sufficient capacity of rainfall intensity measurement under extreme conditions like Jangma (Bai-u season). Compared with existing commercial models which employ a water drop measurement method, our method can give a practical solution for diagnostic check of remote rain gauges using two independent signals.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.221-226
• /
• 2006

This study is about backwash condition and membrane fouling at continuous filtration process in ballast water treatment. Displayed result that handle particle contaminant and hydrospace organism included a number of ballast that is happened in ship using automatic back washing filter. Reason that removes first contaminant that is included in number of ballast is that heighten processing effect of after processing process of the filter. Another advantage is to drop off the solids with controlling revolution of drum screen in pretreatment filtration process. The capacity of pilot plant was $10m^3/h$. The result of the test, Backwash cycle time and duration time and a signification effect on the efficiency of system and backwash Backwash duration time was determined to be fixed in 6 seconds of the system with more than 95% removal rate, It needed 1hour backwash frequency. Filtration system removal aquatic organism over $70{\mu}m$ in ballast water. This study shows that the filtration treatment system has a potential for the treatment of ballast water.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.475-483
• /
• 2019

Special chemical warfare agents are lethal gases that attack the human respiratory system. One of such gases are blood agents that react with the irons present in the electron transfer system of the human body. This reaction stops internal respiration and eventually causes death. The molecular sizes of these agents are smaller than the pores of an activated carbon, making chemical adsorption the only alternative method for removing them. In this study, we carried out a Computational Fluid Dynamics simulation by passing a blood agent: cyanogen chloride gas through an SG-1 gas mask canister developed by SG Safety Corporation. The adsorption bed consisted of a Silver-Zinc-Molybdenum-Triethylenediamine activated carbon impregnated with copper, silver, zinc and molybdenum ions. The kinetic analysis of the chemical adsorption was performed in accordance with the test procedure for the gas mask canister and was validated by the kinetic data obtained from experimental results. We predicted the dynamic behaviors of the main variables such as the pressure drop inside the canister and the amount of gas adsorbed by chemisorption. By using a granular packed bed instead of the Ergun equation that is used to model porous materials in Computational Fluid Dynamics, applicable results of the activated carbon were obtained. Dynamic simulations and flow analyses of the chemical adsorption with varying gas flow rates were also executed.

• Geomechanics and Engineering
• /
• v.17 no.4
• /
• pp.333-342
• /
• 2019

Geological dynamic hazards during coal mining can be caused by the failure of a composite system consisting of roof rock and coal layers, subject to different loading rates due to different advancing velocities in the working face. In this paper, the uniaxial compression test simulations on the composite rock-coal layers were performed using $PFC^{2D}$ software and especially the effects of loading rate on the stress-strain behavior, strength characteristics and crack nucleation, propagation and coalescence in a composite layer were analyzed. In addition, considering the composite layer, the mechanisms for the advanced bore decompression in coal to prevent the geological dynamic hazards at a rapid advancing velocity of working face were explored. The uniaxial compressive strength and peak strain are found to increase with the increase of loading rate. After post-peak point, the stress-strain curve shows a steep stepped drop at a low loading rate, while the stress-strain curve exhibits a slowly progressive decrease at a high loading rate. The cracking mainly occurs within coal, and no apparent cracking is observed for rock. While at a high loading rate, the rock near the bedding plane is damaged by rapid crack propagation in coal. The cracking pattern is not a single shear zone, but exhibits as two simultaneously propagating shear zones in a "X" shape. Following this, the coal breaks into many pieces and the fragment size and number increase with loading rate. Whereas a low loading rate promotes the development of tensile crack, the failure pattern shows a V-shaped hybrid shear and tensile failure. The shear failure becomes dominant with an increasing loading rate. Meanwhile, with the increase of loading rate, the width of the main shear failure zone increases. Moreover, the advanced bore decompression changes the physical property and energy accumulation conditions of the composite layer, which increases the strain energy dissipation, and the occurrence possibility of geological dynamic hazards is reduced at a rapid advancing velocity of working face.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.1
• /
• pp.80-95
• /
• 2015

The purpose of this study was to reduce the drop out rates and enhance the quality of docent training education program in the Nature Heritage Center by providing educational services appropriate to the docents' needs based on the docents satisfaction survey. In this research, we conducted the survey to analyze the importance-satisfaction of natural heritage docent satisfaction in natural heritage docent training programs. The subjects of this survey were 30 docent in Natural Heritage Center. To develop a questionnaire, a factor analysis was conducted, as a result, 6 factors and 22 questions were presented. They are 'curriculum and instruction', 'advice for docent', 'educational environments', 'administrative services', 'support for docents', 'docent life'. The results of t-test, there was a significant difference between importance and satisfaction of the every 22 questions, the mean score of satisfaction(M=3.87, SD=.08) was lower than that of importance(M=4.10, SD=.20). According to ISA, the items located in "concentrate here" were deduced. They are 3 items from administrative services, device for docent, curriculum and instructions. To put in concretely, They were 'lecture content(subject)', 'teaching method', 'service attitude of personnel', 'interest in a docent' Based on these results and descriptive responses from the docents, the strategies for docent satisfaction in natural heritage docents training programs were suggested.

• Resources Recycling
• /
• v.28 no.3
• /
• pp.15-20
• /
• 2019

The recovery of struvite using nitrogen and phosphorus in wastewaters is useful for prevention of eutrophication and use as fertilizer, but there are theoretical and technical issues to be resolved. Through the detailed literature review, this study discusses the possible reasonable prediction of struvite formation reaction by setting a feasible reaction equation with some theoretical considerations. In a technical aspect, the purity of struvite in solid precipitates can be promoted by excluding Ca in an effective way. As for the struvite reaction prediction issue, selection of proper equilibrium reaction as well as its reaction equilibrium coefficient is significant in the neutral and basic pH regions. The equilibrium reaction agrees well with the experimental batch test results. Considering the charge balance of the ions, the pH drop along struvite formation in a diluted solution can be predicted. Also, improvement of struvite purity through elimination of Ca can be expected by providing a highly concentrated ${NH_4}^+-N$ relative to ${HPO_4}^{2-}-P$ because ${NH_4}^+$ can enhance the thermodynamic driving force toward favorable struvite formation. Even though the phosphate reacts rapidly with Ca to form a solid precipitate, the thermodynamic driving force due to the high ${NH_4}^+$ activity can dissociate the phosphate-calcium precipitates and produce struvite.

• Geomechanics and Engineering
• /
• v.24 no.3
• /
• pp.215-226
• /
• 2021

To study the evolution mechanism of cracks in rocks with multiple defects, rock-like samples with multiple defects, such as strip-shaped through-going cracks and cavity groups, are used, and the crack propagation law and changes in AE (acoustic emission) and strain of cavity groups under different inclination angles are studied. According to the test results, an increase in the cavity group inclination angle can facilitate the initial damage degree of the rock and weaken the crack initiation stress; the initial crack initiation direction is approximately 90°, and the extension angle is approximately 75~90° from the strip-shaped through-going cracks; thus, the relationship between crack development and cavity group initiation strengthens. The specific performance is as follows: when the initiation angle is 30°, the cracks between the cavities in the cavity group develop relatively independently along the parallel direction of the external load; when the angle is 75°, the cracks between the cavities in the cavity group can interpenetrate, and slip can occur along the inclination of the cavity group under the action of the shear mechanism rupture. With the increase in the inclination angle of the cavity group, the AE energy fluctuation frequency at the peak stress increases, and the stress drop is obvious. The larger the cavity group inclination angle is, the more obvious the energy accumulation and the more severe the rock damage; when the cavity group angle is 30° or 75°, the peak strain of the local area below the strip-shaped through-going fracture plane is approximately three times that when the cavity group angle is 45° and 60°, indicating that cracks are easily generated in the local area monitored by the strain gauge at this angle, and the further development of the cracks weakens the strength of the rock, thereby increasing the probability of major engineering quality damage. The research results will have important reference value for hazard prevention in underground engineering projects through rock with natural and artificial defects, including tunnels and air-raid shelters.