• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.477-477
• /
• 2009

Bimodal Tram developed by KRRI is driven by a series Hybrid propulsion system which has both the CNG engine, generator and LPB(Lithium Polymer Battery) pack. It has three driving modes; Hybrid mode, Engine mode and Battery mode. Even in case of Battery mode, LPB pack to get enough power to drive the vehicle only by itself onsists of 168 LPB cells(80Ah per lcell), 650V. It is important thing to manage LPB pack in a right way, which will extend the lifetime of LPB cells and operate in the hybrid mode effectively. This paper has shown the development of battery management system(12 BMS, 1 BMS per 14cells) to manage LPB pack which is connected with CAN(Controller Area Network) each other and measure the voltage, current, temperature and also control the cooling fan inside of LPB pack. Using the measured data, BMS can show the SOC(State of Charge), SOH(State of Health) and other status of LPB pack including of the cell balancing.

• 대한전자공학회논문지
• /
• 제18권4호
• /
• pp.34-42
• /
• 1981

PMOS집적기술을 이용하여 512-Bit mask programmable ROM을 설계하고 제작하였다. ROM의 내용은 제작공정에서 gate pattern으로 기억시켰으며 chip의 출력을 512(32×16)개의 점의 행렬로써 오실로스코프에 나타내어 확인하였다. 제작된 chip은 -6V와 - l2V의 범위에서 정상적으로 동작하였다 소모전력과 전달지연시간은 -6V에서 각각 3mW와 13μsec였다. -12V에서는 소모전력이 27mW로 증가하였으며 전달지연시간은 3μsec로 감소하였다. Chip의 출력은 TTL gate의 인력을 직접 구동시킬 수 있었으며 chip select에 의하여 출력을 disable 시켰을 때는 높은 임피던스 상태를 유지하였다.

• 대한전기학회논문지
• /
• 제35권12호
• /
• pp.541-554
• /
• 1986

This paper presents the results of driving performance analysis of permanent magnet synchronous motor using a microprocessor based control system. The system consists of three phase power transistor inverters, three phase controlled rectifier, three central processing units, and sensors. The three CPUs are, respectively, used to generate PWM control signals for the inverter generating three phase sine wave, to generate the gate control signals for firing the converter, and to supervise other two CPUs. The supervisor is used to compute PI control algtorithm to three phase reference sine wave for the inverter. It is also used to maintain a constant voltage frequency ratio for the converter operating as a constant torque controller. The inverter CPU retrieves precomputed PWM patterns from look up tables because of computation speed limitations found in almost available microprocessors. The converter CPU also retrieves precomputed gate control patterns from another look-up tables. For protecting the control ststem from any damage by extraordinary over currents, the supervisor receives the data from current sensor, CT, and break down the CB to isolate the circuits from source. A resolver has a good performance characteristics of overall speed range, especially on low speed range. Therefor the speed control accuracy is impoved. The microprocessor based PM synchronous motor control system, thus, has many advantages such as constant torque characteristics, improvement of wave, limitation on extraordinary over currents, improvement of speed control accuracy, and fast response speed control using multi-CPU and look-up tables.

• 전기학회논문지P
• /
• 제54권3호
• /
• pp.111-118
• /
• 2005

Since the residential load is an AC load and the output of solar cell is DC power, the photovoltaic system needs the DC/AC converter to utilize solar cell. In case of driving to interact with utility line, in order to operate at unity power factor, converter must provide the sinusoidal wave current and voltage with same phase of utility line. Since output of solar cell is greatly fluctuated by insolation, it is necessary that the operation of solar cell output in the range of the vicinity of maximum power point. In this paper, DC/AC converter is three phase PWM converter with smoothing reactor. And then, feed-forward control used to obtain a superior characteristic for current control and digital PLL circuit used to detect the phase of utility line.

• 전기학회논문지P
• /
• 제55권1호
• /
• pp.26-30
• /
• 2006

For the purpose of developing capacitive humidity sensor having interdigital electrodes, interdigital electrode was modeled and simulated to obtain capacitance and sensitivity as a function of geometric parameters like the structural gap and thickness. For the development of ASIC, switched capacitor signal processing circuits for capacitive humidity sensor were designed and simulated by Cadence using $0.25{\mu}m$ CMOS process parameters. The signal processing circuits are composed of amplifier for voltage gain control, and clock generator for sensor driving and switch control. The characteristics of the fabricated sensors are; 1) sensitivity is 9fF/%R.H., 2) temperature coefficient of offset(TCO) is $0.4%R.H./^{\circ}C$, 3) nonlinearity is 1.2%FS, 4) hysteresis is 1.5%FS in humidity range of $3%R.H.{\sim}98%R.H.$. The response time is 50 seconds in adsorption and 70 seconds in desorption. Fabricated process used in this capacitive humidity sensor having interdigital electrode are just as similar as conventional IC process technology. Therefore this can be easily mass produced with low cost, simple circuit and utilized in many applications for both industrial and environmental measurement and control system, such as monitoring system of environment, automobile, displayer, IC process room, and laboratory etc.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.216-219
• /
• 2003

The resonant inverter is widely used for induction heating, electronic ballast and supersonic motor driving circuit. In the meantime, control techniques of PWM, PFM etc.. are mainly applied to control the output power of the resonant inverter. But, in the case of using the half bridge resonant inverter, it is difficult to control the output power by PWM, because its main circuit does not provide the load free-wheeling mode. Therefore, PAM or PFM was usually applied to control output power of half bridge resonant inverter. However, PAM needs a variable DC voltage source, which makes the system structure more complex. On the other hand, in case of PFM, efficiency is declined by operation with poor power factor. This paper Proposed the novel half bridge resonant inverter which can provide the load free-wheeling mode. Also its analysis results for PWM operation with unity fundamental power factor are Presented and compared with other resonant inverters using PWM and PFM.

• 한국수소및신에너지학회논문집
• /
• 제25권3호
• /
• pp.289-296
• /
• 2014

Here, we have studied the effect of water added electrolyte on the photovoltaic performance of dye-sensitized solar cells (DSSCs). It was found that open-circuit voltage ($V_{oc}$) increased and short-circuit current density ($j_{sc}$) decreased with the increase of the amount of added water in the electrolyte of the DSSCs. Electrochemical impedance spectroscopy (EIS) study showed that the electrolyte with added water shifted the dye loaded $TiO_2$ conduction band upward that eventually increased $V_{oc}$ of the cells. On the other hand, the upward shift of $TiO_2$ conduction band decreased the driving force for the electron injection from the lowest unoccupied molecular orbital (LUMO) of the dye molecules to the conduction band of $TiO_2$ that resulted in decreased $j_{sc}$.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.8-16
• /
• 2006

The communication through optical fiber is taking an important role of the expansion of communication network with excellent transmitting rate and quality. As the optical communication is introduced to the backbone network at first and becomes a general communication method of network, the demand of kernel parts of optical communication such as PLC(Planar Light Circuit), Coupler, and WDM(Wavelength Division Multiplexing) element increases. The alignment and the attachment technology are very important in the fabrication of optical elements. In this paper, the driving mechanism of ultra precision stage is studied with the aim of optimal design of stage. The travel and the resolution of stage are investigated. The hysteresis of the stage is generated because of PZT actuator. The hysteresis and the inverse hysteresis are modeled in X, Y, and Z-axis motion. The input data of desired displacement of the stage according to input voltage is obtained from the inverse hysteresis equation. In the result of experiments with the input data, the errors due to hysteresis are well compensated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1219-1222
• /
• 2005

As the optical communication is introduced to the backbone network at first and becomes a general communication method of network, the demand of kernel parts of optical communication such as PLC(Planar Light Circuit), Coupler, and WDM(Wavelength Division Multiplexing) element increases. The alignment and the attachment technology are very important in the fabrication of optical elements. In this paper, the driving mechanism of ultra precision stage is studied with the aim of optimal design of stage. The travel and the resolution of stage are investigated. The hysteresis of the stage is generated because of PZT actuator. The hysteresis and the inverse hysteresis are modeled in X, Y, and Z-axis motion. The input data of desired displacement to the stage according to input voltage is obtained from the inverse hysteresis equation. In the result of experiments with the input data, the errors due to hysteresis are well compensated.

• 한국전자통신학회논문지
• /
• 제11권9호
• /
• pp.869-876
• /
• 2016

위상변조 풀브리지 컨버터를 설계, 개발하는데 있어, 전력반도체와 그 전력반도체 구동회로, 변압기 및 인덕터, 정류기 등을 포함한 많은 설계 요인들이 존재한다. 그 중에서 위상변조 풀브리지 컨버터의 최적 성능에 매우 큰 영향을 끼치는 것은 변압기 설계이다. 특히 변압기 설계는 대형 컴퓨터 데이터센터에 사용되는 전원장치에서처럼 저전압, 고전류 응용에서 매우 중요하다. 이 논문에서는 위상변조 풀브리지 컨버터의 최적 성능을위한 변압기 설계에 관한 연구 결과를 발표한다. 변압기 설계에 관련된 설계 수식들을 유도하고 세밀한 분석을 한다. 이를 토대로, 12V, 1200W 서버전원장치 응용을 위한 위상변조 풀브리지 컨버터 최적 성능을 위한 변압기 설계를 결과물로 제시한다.