• Journal of Power System Engineering
• /
• v.15 no.6
• /
• pp.95-100
• /
• 2011

In this study, an evaluation equation of energy efficiency of pneumatic driving apparatus is proposed. The evaluation equation is derived from state equation and energy equation of air in a control volume, and, the equation of motion of a moving part of a pneumatic cylinder. As a result, distribution of consumption energy and energy efficiency of pneumatic driving apparatus can be analyzed quantitatively. The effectiveness of the proposed method is proved by a pneumatic cylinder driving apparatus using a meter-out driving method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.336-336
• /
• 2000

This paper studied on the yaw motion of the gantry crane which is used for the automated container terminal. Though several problems are occurred in driving of gantry crane, they are solved by the motion by the operator. But if the gantry crane is unmanned, it is automatically controlled without any human operation. There are two types, cone and flat typo in driving wheel shape. In cone type, lateral vibration and yaw motion of crane are issued. To bring a solution to these problems, the dynamic equation of the gantry crane driving mechanism is derived and it used PD(Proportional-Derivative) controller to control the lateral vibration. The simulation result of the driving mechanism using the Runge-Kutta method is presented in this paper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.267-272
• /
• 2014

In this paper, we analyze the characteristics for the driving shock resistance of the military vehicle through the bump test. Prior to the experiment, theoretical analysis was performed by using the SRS(shock response spectrum) and VRS(vibration response spectrum) analysis method. And we estimated the characteristics for the driving shock resistance of the military vehicle. Bump test was performed using the acceleration sensor and the driving test at a different speed. We evaluated the characteristics for the driving shock resistance of the military vehicle based on the result. And predicted values were compared with the theoretical analysis. In addition, we evaluated the results of the theoretical prediction of the SRS and the VRS analysis. And we evaluate the suitability of the prediction method at military vehicle shock analysis.

• Journal of Korean Society of Transportation
• /
• v.36 no.1
• /
• pp.51-65
• /
• 2018

Intentional aggressive driving (IAD) is defined as a hazardous driving event that the aggressive driver intentionally threatens neighbor drivers with abrupt longitudinal and lateral maneuvering. This study developed a methodology for detecting IAD events based on the analysis of interactions between aggressive driver and normal driver. Three major aggressive events including rear-close following, side-close driving, and sudden deceleration were analyzed to develop the algorithm. Then, driving simulation experiments were conducted using a multi-agent driving simulator to obtain data to be used for the development of the detection algorithm. In order to detect the driver's intention to attack, a relative evaluation index (Erratic Driving Index, EDI) reflecting the driving pattern was derived. The derived IAD event detection algorithm utilizes both the existing absolute detection method and the relative detection method. It is expected that the proposed methodology can be effectively used for detecting IAD events in support of in-vehicle data recorder technology in practice.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.235-241
• /
• 2000

The existing methods for installation of long steel pipe pile have some uneconomical problems such as increase of installation cost and period due to the welding of two piles and removal of soil plug, and decrease of driving efficiency due to the increase of driving resistance resulting from time effect during the welding of piles and removal of soil plug, etc. Thus, in this study, new installation method for long steel pipe pile is suggested to solve the existing problems, and calibration chamber tests were performed to investigate both driving and economical efficiency for the suggested method. The test results showed that the new method increased bearing capacity, and decreased the installation cost and period for long steel pipe piles compared with existing methods.

• Korean Journal of Materials Research
• /
• v.32 no.7
• /
• pp.320-325
• /
• 2022

Single OLED and tandem OLED was manufactured to analyze the electroluminescence characteristics of DC driving, AC driving, and full-wave rectification driving. The threshold voltage of OLED was the highest in DC driving, and the lowest in full-wave rectification driving due to an improvement of current injection characteristics. The luminance at a driving voltage lower than 10.5 V (8,534 cd/m²) of single OLED and 20 V (7,377 cd/m²) of a tandem OLED showed that the full-wave rectification drive is higher than that of DC drive. The luminous efficiency of OLED is higher in full-wave rectification driving than in DC driving at low voltage, but decrease at high voltage. The full-wave rectification power source may obtain higher current density, higher luminance, and higher current efficiency than the AC power source. In addition, it was confirmed that the characteristics of AC driving and full-wave rectification driving can be predicted from DC driving characteristics by comparing the measured values and calculated values of AC driving and full-wave rectification driving emission characteristics. From the above results, it can be seen that OLED lighting with improved electroluminescence characteristics compared to DC driving is possible using full-wave rectification driving and tandem OLED.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.11-19
• /
• 2004

When pile foundation constructed by driving method, it is desirable to perform monitoring and estimation of pile drivability and bearing capacity using some suitable tools. Dynamic Pile Monitoring yields information regarding the hammer, driving system, and pile and soil behaviour that can be used to confirm the assumptions of wave equation analysis. Dynamic Pile Monitoring is performed with the Pile Driving Analyser. The Pile Driving Analyser (PDA) uses wave propagation theory to compute numerous variables that fully describe the condition of the hammer-pile-soil system in real time, following each hammer impact. This approach allows immediate field verification of hammer performance, driving efficiency, and an estimate of pile capacity. The PDA has been used widely as a most effective control method of pile installations. A set of PDA test was performed at the site of Donghea-1 Gas Platform Jacket which is located east of Ulsan. The drilling core sediments of location of jacket subsoil are composed of mud and sand, silt. In this case study, the results of PDA test which was applied to measurement and estimation of large diameter open ended steel pipe pile driven by underwater hydraulic hammer, MHU-800S, at the marine sediments were summarized.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.417-423
• /
• 2024

This study compared and analyzed the importance of command priority between railway traffic controllers through pairwise comparison of AHP analysis. 27 railway traffic controllers working on metropolitan railway control center, urban railway control center, and unmanned driving control center responded. As a result of the analysis, all the railway traffic controllers generally recognized the train driving control and train signal control as the most important priorities. For the controller in the manned driving system, a train driving control was the highest at 0.375. On the other hand, the controller based on unmanned driving recognized train signal control as the highest priority at 0.469. In the result of the AHP analysis considering all the variables, the braking system was the highest priority at 0.19 based on manned train driving. On the other hand, the controller based on unmanned train driving recognized wired and wireless network systems and SCADA as the highest priority at 0.267.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.884-891
• /
• 2009

An address voltage stabilization circuit for the single-side driving (SSD) method for AC plasma display panels (PDP) is proposed. The single-side driving method, which eliminates a common sustaining driver, uses only two electrodes in a three electrode AC PDP structure. The high-impedance (Hi-Z) mode operation of the data drive ICs during the sustaining period is needed for surface gas-discharge without misfiring in the SSD method but it produces the problem that the address voltage increases up to the breakdown voltage. The proposed circuit based on a flyback converter can stabilize the address voltage under the breakdown voltage and provide better surface gas-discharge performance without any misfiring in the SSD scheme.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1792-1795
• /
• 2007

We have proposed a new driving method which improve the current stability of a-Si:H TFTs for AMOLED. It performs the negative bias annealing on driving TFTs during a certain period of a frame time. In the proposed method, the range of data signals is significantly reduced by modulating VSS.