• Journal of Power Electronics
• /
• 제9권6호
• /
• pp.960-968
• /
• 2009

This paper presents a design optimization process for interior permanent magnet synchronous motors (IPMSM) for hybrid electric compressors (HEC) which are applied to hybrid electrical vehicles. A hybrid electric compressor is composed of an electric motor driving section and an engine driving section which is connected to the engine by a pulley belt. A hybrid electric compressor driving motor requires half of the full driving power of a compressor. Even though an engine is not operated at the idling stop mode, the electric motor drives the air-conditioner compressor by itself so that the air conditioning system can produce its minimum cooling capacity. In this paper, the design optimization of an IPMSM for a 42 (V) applied voltage system is studied using the design of experiment (DOE) and response surface method (RSM) of 6sigma. The driving characteristics of this motor drive system are measured and analyzed by experiment.

• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.8-13
• /
• 2020

In this paper, the electric vehicle (EV) and internal combustion engine vehicle (ICEV) are compared for different driving cases. The EV exhibits a lower powertrain efficiency when driven on the aggressive driving cycle than when driven on the moderate cycle. In particular, EV powertrain efficiency is low when the battery state of charge (SOC) is low, but ICEV efficiency increases when the driving cycle changes from the moderate cycle to the aggressive cycle. Based on these results, attempts can be made to increase EV powertrain efficiency. EV charging before the battery power drops to a low charging state can reduce energy consumption by 2.7% for an urban area. Furthermore, ECO driving has a more significant effect on EVs than on ICEVs.

• 한국안전학회지
• /
• 제12권3호
• /
• pp.17-22
• /
• 1997

This paper reals with the structure and function of duel mass flywheel. Damping effects of engine rotational fluctuation are compared with those of pre-damper clutch and duel mass flywheel and driven- system behavior is estimated engine idle r.p.m. The reason of gear rattle noise is higher in summer than winter and driving longer period than initial driving is due to affection by drag torque changing. The above-contents can be used on the design of clutch system and transmission matching including engine and duel mass flywheel.

• 한국대기환경학회지
• /
• 제21권6호
• /
• pp.585-592
• /
• 2005

Nowadays it has been strongly required to control emissions from vehicles specially in diesel engines because of increasing number of vehicle in korea. This research aims to provide with some of deterioration factors on vehicles for emissions characteristics and the test was done on an electronically controlled heavy-duty diesel engine under severe driving conditions such as 1200 driving hours, 220,000 km driving distance and a full load. Under various driving conditions, CO, HC, $NO_{x}$, PM and Soots emissions were estimated under D-13 mode and D-3 mode respectively. CO emission was not changed until 500 running hours, and as engine aging is progressed THC was not changed until 500 running hours but it decreased to about $33\%,\;NO_{x}$ decreased constantly but on the other hand PM increased up to $6.9\%$ during the aging process.

• 한국분무공학회지
• /
• 제21권1호
• /
• pp.1-6
• /
• 2016

A gasoline injector rig which can measure cumulative injected fuel mass under a vehicle driving condition was developed. The measurement system consists of an engine control unit (ECU), data acquisition (DAQ) and injected fuel collection system using loadcells. By supplying reconstructed sensor signals which simulate the real vehicle's sensor signals to the ECU, the ECU drives injectors as if they were driven in the vehicle. The vehicle's performance was computer simulated by using $GT-Suite^{(R)}$ software based on both engine part load performance and automatic transmission shift map. Throttle valve position, engine and vehicle speed, air mass flow rate et al. were computer simulated. The used vehicle driving pattern for the simulation was FTP-75 mode. For reconstructing the real vehicle sensor signals which are correspondent to the $GT-Suite^{(R)}$ simulated vehicle's performance, the DAQ systems were used. The injected fuel was collected with mess cylinders. The collected fuel mass in the mess cylinder with elapsed time after starting FTP-75 driving mode was measured using loadcells. The developed method shows highly improved performance in fast timing and accuracy of the cumulative injected fuel mass measurement under the vehicle driven condition.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.1-6
• /
• 2002

Engine lubrication system is generally affected by vehicle driving conditions, which are composed of acceleration, braking deceleration and accelerating during cornering. The major reason is due to the oil pan system in which oil is directly influenced by inertia farce caused by vehicle driving conditions. Therefore, to confirm safety of engine lubrication system inertia farce effects are also considered in the developing state. For the purpose, we have carried the engine tilting tests using ourselves made test rig. Verifying the test results we also measured the inertia effects on the engine lubrication system using the circular tuning and slalom test with vehicle. Through the comparison study between two kinds of results we obtained that the engine tilting test rig was very useful to confirm the safety evaluation of engine lubrication system.

• 산업기술연구
• /
• 제26권B호
• /
• pp.21-28
• /
• 2006

A diesel truck of 1 ton is re-powered by a gasoline engine and the fuelling system of gasoline engine modified to gasoline/CNG bi fuel system. The engine characteristics such as fuel economy and power are evaluated by driving rest, sloping test and dynamometer. The driving test prove the driving cost is saved by 55% and the maximum speed is raised by 13%, which is mainly due to the higher calorific value of CNG. The sloping test is done on the road of which slope is 15%. The truck shows the mean velocity of 88km/h, which means that a re-powered truck is working fine. The BHP are measured by dynamometer. The power and torque produced by a re-powered truck are reduced by 13% and 14% respectively from the power of gasoline engine. The BHP reduction is one of main problems which one has to solve in near future.

• Journal of Biosystems Engineering
• /
• 제26권1호
• /
• pp.11-20
• /
• 2001

Experiments under the stationary and harvesting condition, were performed in order to investigate the vibration characteristics of a head-feeding combine. 6 degrees of freedom components of acceleration at the location of the center of the gravity, and 3 degrees of freedom components of acceleration at the location of the operator seat were measured independently. The vibration characteristics of the combine were estimated with the power spectral density of the time series data of accelerations. From this research, the following results were obtained. 1. Vibration of a head-feeding combine under the stationary condition(engine, thresher and cutter are driven without harvesting) is mainly influenced by the engine. Further, 1/3, 1/2 (sub-harmonic) frequency components of the engine are observed besides engine driving frequency component(45Hz). 2. Vibration of a head-feeding combine under the harvesting condition is influenced by the engine, threshing unit and driving unit. Namely, some kinds of vibration frequency components in harvesting are observed compared with stationary condition. Further, sub-harmonic frequency components of the engine are observed besides engine driving frequency component as same as stationary condition. From these results, it may be concluded that vibration of a head-feeding combine is characteristics of semi-periodic and nonlinear vibration.

• 한국분무공학회지
• /
• 제16권2호
• /
• pp.97-103
• /
• 2011

The electronically controlled diesel engine was converted to dual fuel engine system. Test engine was set up for investigating the power output, thermal efficiency and emissions. ND 13-mode tests were employed for the engine test cycle. The emission result of dual fuel mode meets Euro-4 (K2006) regulation and the engine performance of dual fuel engine was comparable to the performance of diesel engine. To estimate economical efficiency, test vehicles have been operated on a certain driving route repeatedly. Fuel economy, maximum driving distance per refueling and driveability were examined on the road including free ways. Developed vehicle can be operated over 500 km with dual fuel mode and shows 80% of diesel substitution ratio. Driveability of dual fuel mode is similar with that of diesel mode.

• 한국분무공학회지
• /
• 제23권3호
• /
• pp.122-127
• /
• 2018

Recently, registrated passenger cars have increased and were close about seventy million at the end 2017 year in Korea. Among the passenger car using gasoline fuel make up forty six percentage of total registrated vehicles. In this study, investigation on real driving emission characteristics in the passenger car using gasoline fuel with various engine displacements were carried out. The real driving emission characteristics were measured and analyzed by using PEMS (Portable Emission Measurement System). PEMS was composed of gas analyzer, emission flow meter and sample conditioning system et al. Also, test six vehicles were selected to the gasoline passenger car with engine displacement from 1.6L to 3.7L. Two test routes with engine start of cold and hot conditions were applied to analyze the emission characteristics of RDE, respectively. The results show that the $CO_2$ emission have a increasing trend as the engine displacement and vehicle weight. Also, it is guessed that the $CO_2$ emission and vehicle weight were more correlated than the engine displacements. On the other hand, NOx emissions of RDE have not increasing or decreasing tendency according engine displacements or vehicle weight because the activation of three-way catalyst in the gasoline vehicles.