• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.18-23
• /
• 2005

This paper reports experimental results on microdrilling process for silicon parts used in semiconductor equipments. An experimental system was developed consisting of a high speed precision machine, microscope system, and project profile instrument. The experimental results indicate that the amount of chipping at the entrance and exit of micro hole decreases as the spindle speed increases up to 18,000 rpm. At higher spindle speed, however, the amount of chipping increases rapidly. The amount of chipping and infeed rate show proportional relationship up to 20 m/min of infeed rate. Beyond that infeed rate, however, sudden increase in the amount of chipping has occurred.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1021-1024
• /
• 2001

Out of all metal-cutting processes, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. In this paper, the vision system of the sensing methods of drill flank wear on the basis of image processing is used to detect the wear pattern by non-contact and direct method and get the reliable wear information about drill. In image processing of acquired image, median filter is applied for noise removal. The vision flank wear area of the drill was measured. Backpropagation neural networks (BPns) were used for no-line detection of drill wear. The neural network consisted of three layers: input, hidden and output. The input vectors comprised of spindle rotational speed, feed rates, vision flank wear, thrust and torque signals. The output was the drill wear state which was either usable or failure. Drilling experiments with various spindle rotational speed and feed rates were carried out. The learning process was peformed effectively by utilizing backpropagation. The detection of the abnormal states using BPNs achieved 96.4% reliability even when the spindle rotational speed and feedrate were changed.

• 한국생산제조학회지
• /
• 제8권1호
• /
• pp.81-88
• /
• 1999

This paper was carried out to know the influence of advanced austempered ductile cast iron (ADI) on the tool life and mechanical properties of drilling machinability. For manufactured method of ADI, the spheroidal graphite cast iron were austenized at 90$0^{\circ}C$ for 1 hour and then austempered for 2 hour at 37$0^{\circ}C$ in the salt bath. And interrelationship has been investigated between tool life and mechanical characteristics of specimen material on drilling condition when the ordinary and step-feed drilling are carried out to drill holes of specimens. Tensile strength and hardness of ADI decrease and elongation of ADI increases with the increase austempered temperature. It is known that about 2 times of tool life in the case of step-feed decreases compared with ordinary feed due to the high hardness of ADI and hardness ascribed to the fact that retained austenite became to martensite state due to cutting heat in drilling. Under the constant feed rate 0.1mm/rev relation between hardness and length of end tip after drilling can be formularized to Hv=$788.46L^{-0.096}$ for the cutting speed 6.1m/min.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.993-998
• /
• 2002

watches, air bearings and printed circuit hoards (PCB). However, it is not easy to determine optimum cutting conditions since the micro drilling process is very sensitive to various disturbances. Also, undesirable characteristics to optimize the micro drilling are small signal-to-noise ratios, drill wandering motions and high aspect ratios. Thus, in this study, experimental design methods are applied to determine optimum cutting conditions. Suing the methods, three cutting parameters, fred, step and curving speed are optimized to minimize thrust forces. Obtained conditions are verified through required experimental works. As the results, it is shown that the experimental methods can be applied to micro drilling processes to determine Optimum Cutting Conditions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.225-230
• /
• 2001

Small diameter drilling which take high precision in cutting work is needed more small hole and high speed working. Especially, small hole deep drilling is one of the most important machining types and its necessity and importance become more and more increasing in the whole field of industry. This paper shows the limit depths with small diameter drills using experimental analysis. The results are gained by tool dynamometer and Labview system and obtained during small diameter twist drilling system on SM45C steel for different machining conditions. The machine and tools are the CNC machining center and twist drill of diameter 1.5mm. And additionally, tool microscope show the relationship between shapes of chips and breakage shapes of small diameter drills.

• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.71-78
• /
• 2003

The exit burrs in the micro-drilling of precision miniature holes are of interest, especially for ductile materials. As burrs from this process can be difficult to remove, it is important to acquire the way of predicting burr types as well as optimal cutting conditions which minimize the burrs. In this paper, an artificial neural network was used for the prediction of burr formation in micro-drilling. First, the influence of cutting conditions including cutting speed, feed and drill diameter on the exit burr characteristics, such as burr size and type, were observed and analyzed. Then. the burr types were classified by using the influential experimental data as input parameters to the neural nets.

• 한국레이저가공학회지
• /
• 제10권3호
• /
• pp.11-14
• /
• 2007

A trepanning optics is the optical system which makes focus laser beam rotate and incline to the material processing surface. The trepanning optics is used in order to improve the quality of laser drilling process and control the taper of drilling diameter. In order to make trepanning optics, we can use the eccentricity of lens, scanner using two mirror, dove prism, or wedge. Among these method, in this paper wedge is used for trepanning optics. The wedge trepanning optics has advantage on the high speed of rotation. In this paper, we design the wedge trepanning optics using ray tracing. ements and engine design variables of system to satisfy the customer's requirements.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.203-208
• /
• 1998

Carbon fiber epoxy composite materials are widely used in the structures of aircrafts, robots and other machines because of their high specific strength, high specific stiffness and high damping. In order for the composite materials to be used in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joints must be provided, which require precise machining. In this paper, the machinability characterisitcs of the drilling operation of the carbon fiber epoxy composite materials was experimentally investigated. The experimental results are as follows 1.The entrance of hole is very good manufacturing existing, but exit come to occur sever surface exfoliation. 2. The cutting force in drilling of the carbon fiber epoxy composite materials is decreased as the drilling speed increased. 3.The hole of the carbon fiber epoxy composite materials is not good manufacturing by use of the standard twist, therefore, the new drill designed in order to accurate hole.

• Composites Research
• /
• 제26권6호
• /
• pp.380-385
• /
• 2013

본 논문에서는 유리섬유복합재(glass fiber reinforced plastic composites)의 드릴가공조건변화에 따른 박리지수와 표면조도 특성이 분석되었다. 드릴 가공된 홀의 입출구에서 이미지 픽셀을 이용하여 박리지수를 산출할 수 있는 관계식이 유도되었으며, 복합재 시편을 제작하여 진동 및 열 영향을 최소화할 수 있는 가공조건에서 드릴가공을 수행하여 보다 신뢰성 있게 표면조도값을 얻기 위하여 6점평균표면조도측정 방식이 적용되었다. 실험 결과로부터 GFRP 드릴가공에서 박리지수는 이송속도 증가에 감소하고, 절삭속도 증가에도 미세하게 감소함을 볼 수 있었다. 또한 드릴가공된 홀 내부에서 표면조도는 이송속도가 증가할수록 증가하고, 절삭속도 변화에는 영향을 받지 않음이 파악되었다.