• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.2
• /
• pp.107-116
• /
• 2017

When drilling operation is being performed, many physical and chemical changes are occurred near wellbore. To handle various changes of well condition and keep drilling process safe, additives of bulk, such as bentonite for increasing density of drilling mud, barite for increasing viscosity of drilling mud, polymer for chemical control, or surfactant, are added into drilling mud through a mud shear mixer. Because the achievement of the required material property through mud mixing system is essential to stabilize drilling system, it is of importance to analyze multi-phase flow during mud mixing process, which is directly related to increase mixing performance of the system and guarantee the safety of the whole drilling system. In this study, a series of liquid-solid flow simulation based on a computational fluid dynamics (CFD) are performed with comparing to solid concentration in experiment by Gilles et al. [2004] to understand the characteristics of liquid-solid mixing in a mud shear mixer. And then, the simulation-based design of shear mixer are carried out to improve mixing performance in a mud handling system.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.1 s.51
• /
• pp.21-33
• /
• 2007

The dispersion/flocculation behavior of bentonite is a major concern in performance of drilling fluid. We studied the dispersion/flocculation characteristics of three commercial bentonites [two CMC (carboxymethyl cellulose) treated and one untreated] in waters of different pHs and salt concentrations. We also examined changes in the viscosity of bentonite suspensions in such waters as a major rheological property of drilling fluid. The dispersion/flocculation behaviors of bentonites were measured by two methods: colorimetric and light scattering method. Light scattering method allows estimating the floc diameter and flocculation rate. The dispersion and flocculation behaviors were diverse with the different bentonites and water qualities. In distilled water, all the bentonites were well dispersed up to first 10 minutes. After that, the CMC-bearing bentonites were flocculated. In salt waters, all the samples were flocculated and the flocculation rate is varied with salt concentration and polymer content. The volume of settled flocs decreased with increasing salt concentration. The flocculation rate and floc diameter increased with decreasing pH of solutions, whereas the volume of settled flocs increased with increasing pH of solutions. The bentonites of fast flocculation behavior had low viscosity. The results of the present study will be helpful in applying bentonites to drilling fluids in diverse environments.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.50-55
• /
• 2017

This study is about the distributions of flow in an air conditioning duct used for marine and oil drilling ships. Three-dimensional steady state turbulence was assumed as a governing equation for describing the flow in the air conditioning duct in this study. We compared the flow field with the pressure distribution according to the inlet velocity for two types of air conditioning duct, and stress and safe factors were simulated using ANSYS W/B. The result of fluid analysis showed an increased pressure drop in the duct according to the inlet velocity. Furthermore, secondary flow and complicated flow characteristics occurred at the bellows zone.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.8
• /
• pp.47-54
• /
• 2009

In this study, a simple and effective method was proposed to minimize electrolytic corrosion on the workpiece during ED-drilling using water as a working fluid. The adhesion of a cover plate onto the surface of the workpiece was greatly effective for suppressing electrolytic corrosion during ED-drilling. The experiment revealed that the adhesion of the cover plate prevented corrosion without causing significant changes in machining characteristics. Using the machining method proposed in this paper, electrolytic-corrosion-free holes can be machined without change in the machinery system. By using corrosion-free hole as a start hole for wire EDM, a lead frame die with high quality was fabricated successfully.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.100-105
• /
• 2008

Cross-drilling on the brake disc is generally known as a way of improving cooling efficiency. In other theories, cross-drilled holes act like a path of gas or water and are also known that they can reduce fading and wetting of brake rotors. However, in disc rotors with cross-drilling, thermal crack phenomena have been reported more frequently and more manufacturing cost should be paid than non cross-drilled disc rotors. In this study, to examine various effects of cross-drilling on the brake disc, two kinds of brake disc rotors, cross-drilled and non cross-drilled, were used in computational fluid dynamic analyses and dynamometer tests.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.5
• /
• pp.331-341
• /
• 2015

A degasser is a separation unit used in drilling to separate gas from the drilling mud. The degasser used in offshore drilling was developed at an early stage of drilling. Since its development, the design of the degasser’s internal structure has been optimized, with many limitations due to the restrictions of experimental and computational performance measurement methods. Despite the recent development of CFD technology for multiphase flow analysis, CFD has only been used in a limited way for degasser internal flow analysis and design optimization. In this study, a design optimization procedure for a degasser’s internal structure design was proposed, and CFD analyses of three types of internal structural designs were performed to evaluate the separation performance. The CFD result for each design type was used for the design optimization and, as the result, an optimized design is proposed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.1-8
• /
• 2018

In drilling Inconel 601, which is used for compressor cases in aircraft engines, a lot of cutting oil must be supplied. This prevents tools from wear and fracture due to the heat buildup resulting from the high-temperature resistance and toughness of this alloy. However, the cutting oil supply has compromised the machining environment. This has caused attention to shift to an environmentally friendly cutting fluid supply system called the Minimum Quantity Lubrication(MQL) system. The aim of this study was to find a more efficient drill processing method using MQL and to verify its performance. To that end, the properties of Inconel that make it difficult -to -drill were studied by a comparison with the drilling of SM45C. Specific factors (i.e., cutting force and tool wear) were examined in relation to the conditions in the MQL-based drilling system. Based on these results, a sealed cover and step feed were proposed as measures to increase the effectiveness of the MQL system. The efficiency of the proposed method was established.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.148-154
• /
• 2001

Drilling is one of the most important operations in machining industry and usually the most efficient and economical method of cutting a hole in metal. From automobile parts to aircraft components, almost every manufactured product requires that holes are to be drilled for the purpose of assembly, creation of fluid passages, and so on. It is therefore desirable to monitor drill wear and hole quality changes during the hole drilling process. One important aspect in controlling the drilling process is monitoring drill wear status. A drill-wear monitoring system provides information about drill status. With the information, optimum planning for tool change is possible. And drill-wear monitoring system in needed to evaluated drilled hole quality and the wear of drill. Accordingly, this paper deals with an on-line drill wear monitoring system of the detection of tool wear with the computer vision and the area of the drill flank wear is analyzed quantitatively by the system.

• Advances in environmental research
• /
• v.6 no.3
• /
• pp.159-171
• /
• 2017

A successful oil well drilling depends largely on a good mud Program. During drilling, mud provides sufficient hydrostatic pressure, removes drill cuttings and cools drill bits. Mud additives are always required to provide sufficient hydrostatic pressure to ensure borehole stability. Barium Sulphate ($BaSO_4$) also known as barite is the prevalent weighting material but there is needed to develop local materials to augment the use of Barite. The present search is concerned on the early Carboniferous succession exposed in Um Bogma Formation, west central Sinai, Egypt as a new weighting agent in drilling fluids. The increases in the cost of drilling fluids and a shortage of using barite have introduced the locale dolomite as alternative weighting materials. The rheological properties of mud drilling samples weighted by local dolomite samples are being examined and investigated to know its potential to be used as a weighting material in drilling mud. Two mud samples were prepared which comprised of fresh water, caustic soda, bentonite and the weighting material. The weighting materials are added to achieve the required density. The first sample: Water-based mud with commercial barite of density between 10.00 lb/gm and 18.00 lb/gm. The second sample: Water-based mud with dolomite of density between 10.00 lb/gm and 18.00 lb/gm. These samples were analyzed and the density, rheological properties, aging of barite and dolomite and solid contents were investigated. At 10.00 lb/gm, the yield point of dolomite was $20.00lb/100ft^2$ and barite $22.00lb/100ft^2$ while the 10 second gel strength of dolomite was $30.00lb/100ft^2$ and $22.00lb/100ft^2$ for barite. Similarly, little difference was observed in plastic and apparent viscosities. At 10.00 lb/gm, the plastic and apparent viscosities of dolomite were 8.00 cp and 20.00 cp while barite was 8.00 cp and 24.00 cp. The result show that dolomite mud sample gave a little higher yield point and gel strength than barite mud sample. Therefore, dolomite has the potential to be used as weighting material in drilling mud in place of barite thereby enhancing the local content initiative of the government. When dolomite is sourced locally and used it will reduce overall mud and drilling costs.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.23-29
• /
• 2018

This study is about the distribution of heat transfer in air conditioning ducts used for marine vessels and oil drilling platforms. As the convective heat transfer coefficient increased, heat transfer was conducted dynamically to inside as it exited to the outlet of duct. The experiment was to determine if the amount of heat transfer generated at the duct exit increased as the convective heat transfer coefficient increased. When the convective heat transfer coefficient was low, the temperature of the duct showed a relatively high temperature difference between the outside and inside of the duct due to the temperature influence of the internal fluid. In case of temperature distribution generated the volume of the duct along the change of the convective heat transfer coefficient, the temperature descended as heat transfer was promoted and the convective heat transfer coefficient increased.