• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4359-4364
• /
• 2012

In this study, we carried out finite element analysis for drill bit design on ground boring. We verified analysis between drill bit analysis results and experiment results of test machine. From the study, the results expect that time and cost reduction for experiment using finite element analysis for determination on drill bit geometry and material property.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.132-140
• /
• 2000

In conventional drilling, burr geometry can be changed according to the variation of drill geometry like point angle, rake angle. Step drilling is proposed to minimize the burr formation in drilling operation. The burr formed in first cutting can be removed in second cutting by the edge in step. The burr formed in second cutting by the edge in step can be minimized according to the change of geometry like, step angle and depth. The mechanism in step drilling is analyzed. Some step drills are applied to drilling the input shaft which is used for vehicle steering. To measure the burr formed in drilling, laser and height gage are used.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.2
• /
• pp.38-45
• /
• 1996

This study was focused on the prediction of the approprite tool life by clarifying the correlation between progressive drill wear and AE signal. on drilling SM45C the following results have been obtained; RMSAE, AE CUM-CNTS had a tendency to increase slowly according to wear size, at 1000rpm, 150mm/min However, these increased suddenly in the range of 0.20~0.22mm wear, about 102 holes and had a tendency to go up and down until the drilling was impossible. The sudden increase of AE signals shows that something is wrong and it is closely connected with drill wear and chipping. It also makes the working surface bad From the above results, AE signals could be used to monitor the drill's condition and to determine the right time to change tools.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.76-80
• /
• 1993

절삭가공중에서 DRILL가공은 일반기계가공 공정중에 23 .approx. 25% 정도의 비율을 점우하고 있는 중요한 위치의 작업의 하나이고 또한 요구되는 정밀도를 만족하기 어렵고, 높은 생산성이 요구되는 가공법이다. 기계가공의 무인화, 자동화, 고능률화 및 정도향상 이라는 측면에서 더욱 이에 대응할 수 있는 가공방법 즉 공작물, 공구재료, 공구형상 및 절삭조건등에 걸쳐 광범위하게 연구개발 되어 져 가고 있다. 이 작업중 특히 곤란한 것은 깊은 구멍가공(DEEP HOLE DRILL)으로서 깊이/직경의 비가 극히 높은(약 5배이상) 절삭가공 의 경우에는 CHIP의 배출, 절삭날부의 윤활, 공구의 진동등의 문제로 인하여 일반적인 절삭가공 공법으로는 가공이 여려운 경우가 많다. 본 연구는 Solid BTA Drill(Mlti-tip Drill Head with Brazed Tips)에 의하여 가공에요구되는 절삭성 분석과 절삭조건의 변화에 따른 공작물의 가공정도 즉, 가공구멍의 직경의 변화, 표면거칠기. 진원도의 변화상태 및 공구의 마모된 현상에 대하여 실험조사하여 공구에 제한된 수명을 연장하고, 제품에 요구되는 품질수준을 확보하는가에 대하여 본 실험을 통하여 분석하도록 하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.105-108
• /
• 1995

So far,in deep drilling process there are several manufacturing problems such as hole deviation, hole over size, circularity,straightness and surface roughness. Whit regard to these problems, we atudied the abrasion process on carbided tip of BTA drill and got the follow test results through the abrasion characteristic test and analysis on cutting mechanism for the drill tooth and guide pad. 1) In SM55C drilling process, the most stable and reasonable drilling speed range for optmum abrasion characteristic of drill tooth was 60m.min. 2) The total drilling torque was about 60kg .deg.cm on condition drilling speed 60m/min and 0.15mm/rev. These results show that the theoretical burnising torque is well accord with the tested torque which is working on guide pad.

• Journal of the Korean Society of Safety
• /
• v.29 no.5
• /
• pp.74-81
• /
• 2014

This study proposes an advanced type of a micropile system. The proposed micropile system consists of perfobond ribs installed steel rod to improve shear capacity between the thread and the grout, and partially expanded drill holes to increase resistance capacity between the grout and the ground. This study contains experimental evaluations on the proposed micropile system to verify the shear capacity of perfobond rib installed on the steel rod and the load-carrying capacity of shear key created by the partially expanded drill hole. Push-out tests were conducted on a rolled screw thread and steel rods which perfobond ribs are installed instead of rolled screw, in order to compare their load-carrying capacity and behavioral characteristics. As a result, it was confirmed that the perfobond-rib steel rods show much superior structural behavior in terms of initial stiffness, ultimate load, and ductile behavior.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.287-293
• /
• 2001

Resently, reduction of industrial products in size and weight has increased by the application of micro-drill for gadgets of high precision and gave rise to a great interest in a micro-drilling. Due to the lack of tool stiffness and the chip Packing, micro-drilling requires not only the robust tool structure which has not affected by the vibration, but also the effective drilling methods designed to prevent tool fracture from cutting troubles. Firstly, this paper presents a new manufacturing process of micro-drill for improving the Product rate and an optimum shape of micro-drill for lengthening the tool life, and secondly between tool life and drilling torque acquired in the inprocess monitoring system.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.8-13
• /
• 2003

CFRP composite has a lot of merits such as mechanical characteristic, light weight and thermal resistance. For these merits CFRP is applied to so many industrial area. In order for the composite materials to be used in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joints must be provided, which require precise machining. In this paper, the relationship between the stack thickness and drill diameter is examined from the drilling experiment, which is the drilling of 16, 32, 48p1ies specimen with the ${\phi}8$, ${\phi}10$, ${\phi}12mm$ cemented carbide drill. The results are analyzed with consideration of cutting force, stack thickness and drill diameter.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.190-195
• /
• 2003

CFRP composite has a lot of merits such as mechanical characteristic, light weight, and thermal resistance. For these merits CFRP is applied to so many industrial area. In this paper, the relationship between the stack thickness and drill diameter is examined from the drilling experiment, which is the drilling of 16, 32, 48 plies specimen with the $\phi$8, $\phi$10, $\phi$12mm cemented carbide drill. The results are analyzed with consideration of cutting force, stack thickness and drill diameter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.182-187
• /
• 1994

트위스트 드릴을 사용한 구멍은 구멍가공중 가장 경제적인 방법중의 하나이다. 그러나 트위스트 드릴에 의한 가공은 길이에 대한 구멍경의 비가 한정되어 있다. 깊이/직경(L/D)의 비가 통상 5배 이상의 경우의 적절한 가공방법은 거압력의 절삭유를 공급할 수 있는 공구를 사용하여 가공하고 있으며, 그 대표적인 방법은 Long drull, Gun drill, BTA drill 및 Ejector drill등이 있다. 이들 방법중 BAT drill은 다른 가공공구에 비하여 우수한 가공능율을 갖고 있다. 그러나 BAT드릴에 의한 심공가공은 1회 가공에 의하여 요구되는 품질을 만족시켜야 함으로 이에 대응한 연구가 요구되고 있다. 따라서 본 연구는 BAT드릴링 시스템에 BAT drrill을 사용하여 심공가공할때 공작물의 형상 즉 표면 거칠기 및 지원도등 미치는 영향에 대하여 실험을 통하여 분석하였다.