• Journal of Korean Neurosurgical Society
• /
• v.37 no.4
• /
• pp.282-286
• /
• 2005

Objective: Symptomatic chronic subdural hematoma(CSDH) is a well-known neurosurgical entity and most of the lesion is managed by surgical treatment. The authors analyze the surgical indication and the treatment results of twist drill craniostomy with closed-system drainage(TDD) for the symptomatic CSDH. Methods: From March 2001 through December 2003, 31 patients who were treated with TDD for the symptomatic CSDH and followed more than 6months were included. The radiologic criteria of TDD in this study were 1) homogeneous density of hematoma on computed tomography(CT), 2) no septation of hematoma on magnetic resonance imaging(MRI), and 3) thicker hematoma more than twice thickness of skull. Surgical procedures were performed on the maximum thickness of hematoma on CT/MRI. Short and long Steinman pins were used to penetrate the skull and hematoma membrane. As the 5L catheter was inserted through the drill hole, it was kept for 1 - 7days for the drainage of CSDH. The patients of CSDH were followed with clinical symptoms and CT studies. Results: Most of all the 31 patients were improved. However, one patient was suffered from postoperative epidural hematoma and the other patients have received the secondary operation because of the recurrence of CSDH on 3 months after initial surgery. Conclusion: TDD is safe procedure for the symptomatic CSDH if the patients are selected appropriately.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.223-230
• /
• 2013

When a new nuclear fuel is developed, an irradiation test needs to be carried out in the research reactor to analyze the performance of the new nuclear fuel. In order to check the performance of a nuclear fuel during the irradiation test in the test loop of a research reactor, sensors need to be attached in and out of the fuel rod and connect them with instrumentation cables to the measuring device located outside of the reactor pool. In particular, to check the temporary temperature change at the center of a nuclear fuel during the irradiation test, a thermocouple should be instrumented at the center of the fuel rod. Therefore, a hole needs to be made at the center of fuel pellet to put in the thermocouple. However, because the hardness and the density of a sintered $UO_2$ pellet are very high, it is difficult to make a small fine hole on a sintered $UO_2$ pellet using a simple drilling machine even though we use a diamond drill bit made by electro deposition. In this study, an automated drilling machine using a CVD diamond drill has been developed to make a fine hole in a fuel pellet without changing tools or breakage of workpiece. A sintered alumina ($Al_2O_3$) block which has a higher hardness than a sintered $UO_2$ pellet is used as a test specimen. Then, it is verified that a precise hole can be drilled off without breakage of the drill bit in a short time.

• Composites Research
• /
• v.30 no.1
• /
• pp.35-40
• /
• 2017

In this study, natural fiber composites including flax fiber reinforcement was manufactured. It was tried to find optimum design of drill and machining factor for minimizing the damage during hole machining in natural fiber composites. Taguchi optimization was used for minimizing the number of experiments and evaluation of the effect of machining factor during hole machining in natural fiber composites. The experimental results indicate that the newly designed drill distributes cutting resistance well and minimizes surface roughness and produces fine surfaces. Developed new drill has been dispersed in the cutting resistance during processing, it was possible to obtain the smooth hole surface. Also, it was found that optimal rotational speed and feed rate of drill for hole machining.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• Journal of the Korean Professional Engineers Association
• /
• v.16 no.3
• /
• pp.5-23
• /
• 1983

On the Seoul Metropolitan Subway Construction of No. 3, 4 Line, the total length is 57 Km and it is now undergoing almost 55％ progress. The working method is classified into Open Cut of 70% and the rest of 30% tunnelling method in the 48 job site. Above tunnelling method is execute by American Steel Support System and the rest of 10 job site carried out by New Austria Tunnelling Method. This paper describes Blasting Standardizations works on the above Tunnelling ' Open Cut Method under big slogan, first safety, second execution. As a superintendent, I strived standardization of works with Better powder, Better Drills ' Better Pattern. Geological structure of Seoul area is composed by Jurassic Granite and also the above rockgroup are over burden by Alluviums as a Unconformity. First of all, I carried out the standard amount of powder and burden through experimental standard blasting by each powder as following Blasting works in the subway construction is surrounding shop Building, under pass the city river and also under pass highest building basement floor. I made allowable Blasting Vibration Value by West-Germany Vornorm DIN 4150, Teil 3 and should measure each blasting works as fellows all of powder is used basically Low-Gravity and Low Velocity such as Slurry, Ammonium Nitrate ' Finex I, II. for Smooth Blasting Instead of Gelatin Dynamite. Electric Detonation Cap is used basically M/S Delay Cup instead of Electric delay ' Simultaneous cap. I applied following formula V=KW3/4 $D^{-2}$ V=Particle Velocity (Cm/sec) K=Ginh Huh's Value W=Delay Charge (Kg) D=Distance(m) In the Open Cut, within 1m distance from H-pile I made to use the Concrete breaker, as following V=7W/$^{0.5}$V/$^{-1.75}$ On the Concentrate Building area, I advise to use Light class drill ø36m Bit and advance 1.1m per round blasting the three boom jumbo drill over ø45mm used only suburb of city.e Light class drill ø36m Bit and advance 1.1m per round blasting the three boom jumbo drill over ø45mm used only suburb of city.

• Journal of Practical Engineering Education
• /
• v.8 no.1
• /
• pp.23-29
• /
• 2016

Our society is endemic in safety insensitivity, yet we have been concerned for safety education and disaster drill since the Sewol Ferry accident. However, the practical training costs very high, and it has its limit to increase reality. Recently, industry fields put emphasis on virtual reality (VR) as alternatives, so various contents are invented by using advantages of VR. The paper explores crucial application in 3-dimensional simulation for fire drill, suggests novel design, and contemplates about educative result through designing process. In order to construct and materialize the suggested system, practical 3D spatial information model and various disaster-drill scenarios are necessary. Also, to apply game elements for augmentation in users' utility, educations based on computer science and visual art are inevitable, which requires skills in programing and modeling respectively. Thus, this study investigates educational effect of convergence field through the suggested system designing process.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.21 no.1
• /
• pp.9-14
• /
• 1976

This experiment was conducted to find out the ., effects of various fertilizer level and Drill-seeding on the growth and yield of the two newly bred naked-barley varieties, Kwangsung and $Bangsa^6$ the former that was bred for the first time in Korea in 1972, is resistant to winter and productive, and the latter that was also bred in Korea by radioisotope treatment in 1974, is of short-stem, early maturing and productive. The grain yield in Drill-seeding was 8 percent higher than that in Conventional seeding. $Bangsa^6$ was more resistant to lodging and more adaptable to the amounts of the increased-fertilizer level than Kwangsung. In Drill-seeding, $Bangsa^6$ is thought to be more suitable naked-barley variety than Kwangsung.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.06a
• /
• pp.3-3
• /
• 2001

Recently TiN, TiAlN, CrN hardcoatings have adapted many industrial application such as die, mold and cutting tools because of good wear resistant and thermal stability. However, in terms of high speed process, general hard coatings have been limited by oxidation and thermal hardness drop. Especially in the case of PCB drill, high speed cutting and without lubricant process condition have not adapted these coatings until now. Therefore more recently, superhard nanocomposite coating which have superhard and good thermal stability have developed. In previous works, WC-TiAlN new nanocomposite film was investigated by cathodic arc ion plating system. Control of AI concentration, WC-TiAlN multi layer composite coating with controlled microstructure was carried out and provides additional enhancement of mechanical properties as well as oxidation resistance at elevated temperature. It is noted that microhardness ofWC-TiA1N multi layer composite coating increased up to 50 Gpa and got thermal stability about $900^{\circ}C$. In this study WC-TiAlN nanocomposite coating was deposited on PCB drill for enhancement of life time. The parameter was A1 concentration and plasma cleaning time for edge sharpness maintaining. The characteristic of WC-TiAlN film formation and wear behaviors are discussed with data from AlES, XRD, EDS and SEM analysis. Through field test, enhancement of life time for PCB drill was measured.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.90-96
• /
• 1998

The ductile cast iron is austempered at 300, 350 and 40$0^{\circ}C$ temperature in order to investigate the basic factors for monitoring drill wear in automatic production process, and cutting force and AE RMS signals are measured with changing cutting condition for ADI(Austempered Ductile Cast Iron) with different mechanical properties. The signals of cutting force were influenced by cutting speed and feedrate greatly. On the other hand AE RMS signals are influenced by cutting speed where as it is not related with feedrate. As the depth of drilling increases, cutting force shows a slow increase and the value of AE RMS increases until the range of h/d=4. But over the range it increases greatly due to an amount of chip discharge and friction with inner wall of drilling hole, etc. As the drill diameter increases at a constant depth of drilling. Cutting force increases linearly, but the level of AE RMS does not increases linearly due to circumferential velocity and great influence of h/d.

• Journal of the Korean Society for Precision Engineering
• /
• v.2 no.2
• /
• pp.43-59
• /
• 1985

In relation to the machinability of drilling operation, experiments were made to investigate the effect of cutting condition on static as well as dynamic cutting resistances in cutting plane carbon steel (SM 45 C) with H.S.S. twist drills. The results were as follows. 1) The static cutting resistances on carbon steel can practically be calculated by the following equations which were derived from experimental result. The deviation from the experimental values was less than 8% and 13% for cutting torque and thrust respectively. For cutting torque M: M=0.019 $H_B\;{f^{0.68}d^{1.68}$ For thrust T: T=0.400406 $r^{0.6}d^{0.68}$ + 0.1835 $H_BC^2$(where $H_B$: Brinnel hardness) 2) The static components of cutting resistance are increased exponentially with increasing drill diameter and feed rate. On the effect of drill diameter, the dynamic components of torque are decreased with increasing dirll diameter because of rigidity, the dynamic components of thrust being not effected with the changes. 3) As feed rates increase, the dynamic components of torque rather decrease although its changes on thrust components are unstable. 4) The static components of cutting resistance and dynamic component of torque are slightly decreased in accordance with the increase of spindle speed although its dynamic thrust components are not effected by the spindle speed.