• Journal of Nutrition and Health
• /
• v.28 no.5
• /
• pp.387-396
• /
• 1995

This study was undertaken to investigate the effect of increase in the ratio of zinc to copper and alcohol consumption on serum lipid content in Sprague-Dawley male rats during five weeks. Sixty rats were divided into six groups, CZ < zinc 30ppm diet >, CZA < zinc 30 ppm diet plus alcohol 5% solution >, HZ < zinc 300ppm diet >, HZA < zinc 300ppm diet plus alcohol 5% solution >, SHZ < zinc 600ppm diet >, SHZA < zinc 600 ppm diet plus alcohol 5% solution >. High ratio of zinc to copper groups < HZ, SHZ > were significantly decreased in high-density lipoprotein (p<0.01) and increased in total cholesterol, triglyceride, total lipid in serum(p<0.001, p<0.001, p<0.01). Triglyceride levels of serum in alcohol groups < CZA, HZA, SHZA > were significantly higher (p<0.001) than non-alcohol group < CCZ, HZ, SHZ >. Copper levels of serum were reduced in group high ratio of zinc to copper. These results present that high ratio of zinc to copper increase cholesterol(p<0.001) and alcohol consumption increase triglyceride(p<0.001) in serum. This close association to lipid metabolism in rats draw attention to the potential significance of zinc and alcohol nutriture in relation to cardiovascular disease.

• The Korean Journal of Applied Statistics
• /
• v.26 no.1
• /
• pp.15-22
• /
• 2013

In clinical study or epidemic research, the $2{\times}2$ frequency table is useful to present a summary statistic The values of four cells in $2{\times}2$ table use to calculate the effect measures such as risk ratio, relative ris ratio or odds ratio. In this paper, we suggest that the improved visualization method using a radar diagram supported by MS-office Excel from the $2{\times}2$ frequency table is able to understand and draw easily betweendiagnosti measures such as sensitivity, specificity, predictivity, and likelihood ratio. We use some numerical example in order to show the usage of the proposed method.

• Fibers and Polymers
• /
• v.6 no.3
• /
• pp.206-218
• /
• 2005

Structural studies of series of 'as spun' and drawn PEEK fibers have been carried out using X-ray diffraction and optical microscopy techniques. The analysis of results suggest that fibers produced at a constant draw ratio with increasing draw temperatures show enhanced orientation and crystalline behaviour. The resolved equatorial and meridional traces provide additional structural parameters in terms of crystallinity, crystallite size, and crystallite thickness. It is concluded that drawing at a temperature below $T_g(i.e.,\;144^{\circ}C)$ results in poorly oriented non-crystalline materials, whereas drawing above $T_g$ results in highly oriented semi crystalline materials. Additional drawing proved to increase the overall orientation with slight improvements in lateral order of the chain molecules. Quantitative analysis revealed that the crystallite size increases with increasing drawing temperature. The results also revealed the increased crystallite size upon additional drawing. Crystalline orientation parameter, $_c$, suggests almost perfect orientation. In all cases, the amorphous orientation is found to be lower than the overall orientation parameter obtained from the optical birefringence. As a result of additional drawing, crystalline orientation was found to increase slightly but the increase in the orientation of non-crystalline material was found to be substantial. An average crystalline density was determined from the orthorhombic unit cell dimensions. It was found to vary as a result of processing conditions. It was also found that the value of the maximum birefringence shows heavy dependence on the chain conformation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1506-1511
• /
• 2002

A computer aided expert system fur spur, helical, bevel and worm gears was newly developed by using AutoiCAD system and its AutoLISP computer language in the present study. Two methods are available for a designer to draw a gear. The first method needs the gear design parameters such as pressure, module, number of tooth, shaft angle, velocity, materials, etc. When the gear design parameters are inputted, a gear is drawn in AutoCAD system and maximum allowable power and shaft diameter are calculated additionally. The second method calculates all dimensions and gear design parameters to draw a gear when the information such as transmission, reduction ratio, nm, materials and pressure are inputted. The system includes four programs. Each program is composed of a data input module, a database module, a strength calculation module, a drawing module, a text module and a drawing edit module. In conclusion, the CAD system would be widely used in companies to find the geometric data and manufacturing course.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.336-341
• /
• 2009

Hydroformed parts have higher dimensional accuracy, structural strength, and dimensional repeatability. Particularly in the automotive industry, manufacturing of parts with complex shapes from tubular materials sometimes requires one or more pre-forming operations such as bending before the hydroforming process. The pre-bending process is an important process for the successful hydroforming in the case where the perimeter of the blank is nearly the same as that of final product. The bendability of a tube depends on the parameters such as the bending radius, welding methods, mechanical properties and hardness. Through the stainless steel tubes bent by rotary draw bending machine, this study shows the following : (1) The influence on spring back ratio variation with stress level in the welded bent tube. (2) The Cross-section ovality variation with weld seam position and bending radius. (3) The relation between elongation and thickness reduction of tension zone with weld seam position and bending radius. (4) Workability evaluation of bent stainless steel tubes through the hardness of materials and hardness increment. The results of this study may help to understanding of characteristics on bendability of stainless steel tubes.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.1
• /
• pp.37-49
• /
• 2014

This paper proposes a optimal process after analyzing the existing papers of software requirements engineering process. In analyzing it examines requirement pursuit management and origin, and considers a variety of starting points that draw requirement documents. Also, this paper considers carefully the multiple methods of stakeholder needs, problem analysis, processing priority of business modeling. From the analyzed result this paper proposes the best method that draws systematically the requirement documents. The proposed method can minimize the requirement changes, draw the higher project success ratio, and satisfy the customer.

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.197-206
• /
• 2022

The purpose of this study was to confirm the optimal spinning conditions for PLA (Polylactic acid) as a fiber forming polymer. According to the melt spinning test results of PLA, the optimal spinning temperature was 258℃. However, it needs to note that relatively high pack pressure was required for spinning at 258℃. At an elevated temperature, 262℃, mono filament was broken easily due to hydrolysis of PLA at a higher temperature. In case of fiber strength, it was confirmed that the draw ratios of 2.7 to 3.3 were optimal for maximum strength of melt spun PLA. Above the draw ratio, 3.3, the strength of the PLA fibers was lowered. It was presumed that cleavage of the PLA polymer chain over maximum elongation. The heat setting temperature of GR (Godet roller) showed that the maximum strength of the PLA fibers was revealed around 100℃. The degree of crystallinity and the strength of the PLA fibers were decreased above 100℃. The optimal take-up speed (Spinning speed) was around 4,000m/min. Thermal analysis of PLA showed 170℃ and 57℃ as Tm (melting temperature) and Tg (glass transition temperature), respectively.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.76-83
• /
• 1997

Blends of thermotropic liquid crystalline polymer(TLCP) with poly(ethylene terephthalate) (PET) were prepared by the coprecipitation from a common solvent. The blends were processed through a capillary die at $287^{\circ}C$ to produce a monofilament. Morphology and mechanical, thermal properties of blends and composites were examined by differential scanning calorimetry(DSC), tensile test, optical microscopy and scanning electron microscopy. Crystallization kinetics of the blends were investigated by the isothermal DSC method. The Avrami analyses were applied to obtain the information on the crystal growth geometry and factors controlling the rate of crystallization. In the blends, liquid crystalline phase did not reveal any significant macrophase separation and thermal degradation at the processing temperature. From scanning electron micrographs of cryogenic fracture surfaces of extruded fibers, the TLCP domains were found to be more or less finely dispersed with $0.1{\mu}m$ to $0.2{\mu}m$ in size. Interfacial adhesion between the TLCP and matrix polymer was excellent. Tensile strength and modulus of TLCP/PET in-situ fiber composites were enhanced with increasing draw ratio and LCP content.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.6
• /
• pp.872-878
• /
• 2012

It is quite important to improve the visual acuity of a medical image by suppressing noisy parts and simultaneously keeping the details of signal components to draw the accurate diagnostics. With this aim, we suggest a novel method to generate Rotational Kernel Transformation (RKT) filter mask with applying Bresenham's algorithm and implement an nonlinear filtering algorithm to eliminate noises. As a result, we can find the fact that RKT filter mask can be automatically created and the visual acuity of a corrupted image can be elevated in terms of the signal-to-noise ratio (SNR) with applying the RKT filter.

• Water for future
• /
• v.22 no.1
• /
• pp.91-98
• /
• 1989

This study was aimed to determine a discharge coefficient of flow through gate piers. The coefficient was Calbrated with water stage data observed during 1984 to 1987 at the Young San Estuary Dam. The coefficient is the function of the dimensionless parameters combined with the difference between up and down stream water level to down stream water depth ratio and water surface draw down ratio. From the verification with existing methods and actual drainages, drainages predicted by the relationship have the most consistency with the actual drainages, also Matthai's method can be used within the proposed condition originally.