• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.12
• /
• pp.1097-1106
• /
• 2011

Unsteady numerical analysis was performed to simulate air-launched missiles from a complete helicopter in hover by using an unstructured overset mesh flow solver coupled with a module of six degree-of-freedom motion of equations. The unsteady computations have been performed to obtain flow fields around the complete helicopter including main rotor, tail rotor, and fuselage equipped with multiple missiles, and six-DOF simulation has been performed to predict the behavior of the air-launched missile. The effects of the launching position and the missile thrust on the trajectory of the missile were investigated as well as the aerodynamic interference of the air-launched missile under the unsteady downwash produced by main rotor.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.4
• /
• pp.530-541
• /
• 1998

Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass transfer coefficients. Downwash of the rotating secondary flow, reattachment of main flow between ribs and the vortices near ribs and wall enhanced the mass transfer locally up to 8 times of that in case of the duct without ribs.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.5
• /
• pp.8-13
• /
• 2004

In order to better understand the characteristics of the flow field around the submerged hydrofoil of finite span with high speed and shallow submergence. a numerical code which can solve the flow around a fast lifting body under the free surface was developed and used to obtain various interesting features of the flow. The code was based on the panel method of Hess( 1972), and the free surface condition was linearized to conform with the assumption of the high Froude number. It is shown that the effect of the change of submerged depth. angle of attack and aspect ratio upon the sectional lift coefficient is rather significant for the case of the chosen example wing, which has the rectangular planform. Since Lee(2002)'s theoretical results were for the wing of elliptical planform, the direct comparison of the two results was not possible. It seems that more computational results are in need to compare the theoretical and the numerical prediction in detail.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.2 s.140
• /
• pp.80-87
• /
• 2005

A set of experiments was carried out for obtaining the velocity field around the hydrofoil of finite span, using a wing of the NACA 0012 section in a circulating water channel. DPIV technique was used to measure the velocity field, and the velocity measurements along the span were done for 3 speeds, 3 submerged depths, and 4 angles of attack. Experimental data are compared with the theoretical assumptions, as well as the numerical findings by Lee and Lee(2004). Special care is given to the flow near the tips and in the region close to the leading edge. Though indirect, using the measured data of the velocity, it is now possible to compare the aerodynamic and the hydrodynamic strength of the circulation distribution of a wing in the framework of the lifting-line theory.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.852-857
• /
• 2018

Vortex Generators are used in heat exchanger to enhance the heat transfer of air side. 3-D numerical analysis is performed on heat transfer characteristics of a channel with trapezoidal vortex generator. We investigate the effects of vortex generators with two different inclined angles to flow direction which are forward and backward vortex generators. The thermal hydraulic performance such as Nu and pressure drop, is compared quantitatively. The results show that vortex generator enhances the heat transfer by developing boundary layers and secondary flow in the downstream. The downwash flow region corresponds to the maximum Nu, while the upwash flow region corresponds to Nu minimum. In the view of the heat transfer characteristics, FVG is better than BVG. However, when flow is turbulent as Re increases, the pressure drop for FVG is higher than that for BVG.

• Journal of the Korean Society of Visualization
• /
• v.18 no.3
• /
• pp.69-76
• /
• 2020

In the present study, we investigate the flow separation characteristics of a paraglider canopy model by tuft visualization. The experiment is conducted at Re = 3.3×105 in a wind tunnel large enough to contain the three-dimensional paraglider canopy model, where Re is Reynolds number based on the mean chord length and the free-stream velocity. The flow separation characteristics of the canopy model near the wing root are similar to those of a two-dimensional airfoil with a cross-section similar to the model. On the other hand, near the wingtip region, the flow separation is suppressed by the downwash induced by the wingtip vortex. As a result, as the angle of attack increases, the flow separation occurs from the wing root region of the canopy model and develops toward the wingtip.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.2
• /
• pp.288-297
• /
• 2000

This paper describes the results of an experimental investigation of the flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices. The test facility consists of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta wings(vortex generators) protruding from the surface. In order to control the strength of the two longitudinal vortices, the angles of attack of the vortex generators are varied from 20 degree to 45 degree, but spacings between the vortex generators are fixed to 4 cm. The 3-dimensional mean velocity downstream of the vortex generators is measured by a five-hole pressure probe, and the hue-capturing method using the thermochromatic liquid crystals has been used to provide the local distribution of the heat transfer coefficient. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the regions where the secondary flow is directed toward the wall and thickened where it is directed away from the wall. The peak augmentation of the local heat transfer coefficient occurs in the downwash region near the point of minimum boundary-layer thickness. Streamwise distributions of averaged Stanton number on the measurement planes show very similar trends for all the cases(${\beta}=20^{circ},\;30^{\circ}\;and\;45^{\circ}$).

• Journal of Environmental Impact Assessment
• /
• v.9 no.4
• /
• pp.323-338
• /
• 2000

A Korean air dispersion modeling software, AirMaster, was developed on a basis of dispersion theories adopted in U.S. EPA's ISC3 (Industrial Source Complex - version 3) model to assess the air quality impact from the stacks. Key characteristics of AirMaster are as follows: 1) The building downwash effect can be easily simulated; 2) The screen, long term, and short term models can be run independently; 3) The input data to run the model such as meteorological and terrain data are supplied automatically from the databases in AirMaster; and 4) The modeling procedure is easy and simple under the GUI window environment. In order to validate AirMaster, comparisons with ISC3 model and Indianapolis tracer experiment were carried out. It was shown that AirMaster was identical to ISCST3 and ISCLT3 models in predicting the 1 hr to annual concentrations from the stack under various stack emission and meteorological conditions. The 1 hr concentrations predicted by AirMaster also showed a good agreement with the Indianapolis tracer measurements.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.519-529
• /
• 2010

In the present study, unsteady calculations have been performed to simulate flows around a UH-60A full configuration including main rotor, fuselage, and tail rotor. A flow solver developed for helicopter aerodynamic analysis was used for the simulation of the complete helicopter in high-speed and low-speed forward flight. Unsteady vibratory loads on the main rotor blades were compared with flight test and other calculated data for the assessment of the present flow solver. Aerodynamic interaction of the three components of the helicopter was investigated by comparing with the results of main-rotor-alone, main rotor and fuselage, and tail-rotor-alone configurations. It was found that the existence of the fuselage has an effect on the normal force distribution of the main rotor by varying downwash distribution on the rotor disc, and tip vortices trailed from the main rotor strongly interact with the tail-rotor.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.