• Steel and Composite Structures
• /
• v.20 no.5
• /
• pp.1043-1066
• /
• 2016

A new analytical solution based on a third order shear deformation theory for the problem of static analysis of cross-ply doubly-curved shells is presented. The boundary-discontinuous generalized double Fourier series method is used to solve highly coupled linear partial differential equations with the mixed type simply supported boundary conditions prescribed on the edges. The complementary boundary constraints are introduced through boundary discontinuities generated by the selected boundary conditions for the derivation of the complementary solution. The numerical accuracy of the solution is compared by studying the comparisons of deflections, stresses and moments of symmetric and anti-symmetric laminated shells with finite element results using commercially available software under uniformly distributed load. Results are in good agreement with finite element counterparts. Additional results of the symmetric and anti-symmetric laminated and sandwich shells under single point load at the center and pressure load, are presented to provide data for the unsolved boundary conditions, benchmark comparisons and verifications.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.2
• /
• pp.141-151
• /
• 2013

In this paper, lateral-torsional buckling(LTB) strength of HSB800 steel plate girder under uniform bending moment was estimated by the nonlinear analysis. Doubly symmetric sections with slender, noncompact and compact webs were considered and the LTB strength in the inelastic range was estimated by taking initial imperfection and residual stress into account. For the numerical analysis, single-panel model and three-panel model were considered and analysis of SM490 steel plate girder was performed to judge the validity of the constructed models by comparing the results with AASHTO, AISC, Eurocode and KHBDC(LSD) codes. By using the same models, LTB strength of HSB800 girder was evaluated and it was acknowledged that the current codes can be applied to HSB800 girders with doubly symmetric section in the inelastic LTB range.

• Steel and Composite Structures
• /
• v.4 no.1
• /
• pp.23-36
• /
• 2004

The inelastic lateral-distortional buckling of doubly-symmetric hot-rolled I-section beam-columns subjected to a concentric axial force and uniform bending with elastic restraint which produce single curvature is investigated in this paper. The numerical model adopted in this paper is an energy-based method which leads to the incremental and iterative solution of a fourth-order eigenproblem, with very rapid solutions being obtained. The elastic restraint considered in this paper is full restraint against translation, but torsional restraint is permitted at the tension flange. Hitherto, a numerical method to analyse the elastic and inelastic lateral-distortional buckling of restrained or unrestrained beam-columns is unavailable. The prediction of the inelastic lateral-distortional buckling load obtained in this study is compared with the inelastic lateral-distortional buckling of restrained beams and the inelastic lateral-torsional buckling solution, by suppressing the out-of-plane web distortion, is published elsewhere and they agree reasonable well. The method is then extended to the lateral-distortional buckling of continuously restrained doubly symmetric I-sections to illustrate the effect of web distortion.

• East Asian mathematical journal
• /
• v.25 no.2
• /
• pp.215-220
• /
• 2009

In this paper, we investigate the generating strings and the number of 2-(edge)connected bipartite Steinhaus graphs.

• Steel and Composite Structures
• /
• v.30 no.5
• /
• pp.483-492
• /
• 2019

In the current study, the influence of the initial lateral (sweep) shape and the cross-sectional twist imperfection on the lateral torsional buckling (LTB) response of doubly-symmetric steel I-beams was investigated. The material imperfection (residual stress) was not considered. For this objective, standard European IPN 300 beam with different unbraced span was numerically analyzed for three imperfection cases: (i) no sweep and no twist (perfect); (ii) three different shapes of global sweep (half-sine, full-sine and full-parabola between the end supports); and (iii) the combination of three different sweeps with initial sinusoidal twist along the beam. The first comparison was done between the results of numerical analyses (FEM) and both a theoretical solution and the code lateral torsional buckling formulations (EC3 and AISC-LRFD). These results with no imperfection effects were then separately compared with three different shapes of global sweep and the presence of initial twist in these sweep shapes. Besides, the effects of the shapes of initial global sweep and the inclusion of sinusoidal twist on the critical buckling load of the beams were investigated to unveil which parameter was considerably effective on LTB response. The most compatible outcomes for the perfect beams was obtained from the AISC-LRFD formulation; however, the EC-3 formulation estimated the $P_{cr}$ load conservatively. The high difference from the EC-3 formulation was predicted to directly originate from the initial imperfection reduction factor and high safety factor in its formulation. Due to no consideration of geometric imperfection in the AISC-LFRD code solution and the theoretical formulation, the need to develop a practical imperfection reduction factor for AISC-LRFD and theoretical formulation was underlined. Initial imperfections were obtained to be more influential on the buckling load, as the unbraced length of a beam approached to the elastic limit unbraced length ($L_r$). Mode-compatible initial imperfection shapes should be taken into account in the design and analysis stages of the I-beam to properly estimate the geometric imperfection influence on the $P_{cr}$ load. Sweep and sweep-twist imperfections led to 10% and 15% decrease in the $P_{cr}$ load, respectively, thus; well-estimated sweep and twist imperfections should considered in the LTB of doubly-symmetric steel I-beams.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.400-403
• /
• 2008

For the effective manufacture of doubly curved metal plates, a line array roll set (LARS) process is proposed. The suggested process utilizes a pair of upper and lower symmetric roll assemblies. In the process, the initial plate is progressed into the final shape in a stepwise or pathwise manner according to the basic principle of the incremental forming process. The deformation proceeds simultaneously in the longitudinal and transverse directions. Moreover, there is a close correlation between the deformation in the longitudinal direction and that in the transverse direction of the plates. Therefore, the finally formed shape in the incremental forming process is strongly dependent upon process conditions, such as the forming path and the forming increment. The manufacturing of arbitrary doubly curved plates with various curvatures is not an easy task because of such complicated behaviors of the plate; thus, the forming schedules for the desired shape should be carefully and accurately designed. In this study, several experiments with the LARS system were carried out for the fundamental investigation on process design for manufacturing of doubly curved plates.

• Communications of the Korean Mathematical Society
• /
• v.11 no.4
• /
• pp.1123-1135
• /
• 1996

In this paper, we introduce some properties of Steinhaus graphs of order n, and prove that the size of some special type of induced cycles in Steinhaus graphs of order n is bounded by $\left\lfloor \frac{n+3}{2} \right\rfloor$.

• Kyungpook Mathematical Journal
• /
• v.48 no.2
• /
• pp.331-335
• /
• 2008

In this paper, we investigate the number of ones in rows of Pascal's Rectangle. Using these results, we determine the existence of regular bipartite Steinhaus graphs. Also, we give an upper bound for the minimum degree of bipartite Steinhaus graphs.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.3 s.36
• /
• pp.509-523
• /
• 1998

A consistent finite element formulation and analytic solutions are presented for stability of thin-walled circular arch. The total potential energy is derived by applying the principle of linearized virtual work and including second order terms of finite semitangential rotations. As a result, the energy functional corresponding to the semitangential moment is newly derived. Analytic solutions for the out-of-plane buckling of symmetric thin-walled curved beam subjected to pure bending or uniform compression with simply supported boundary conditions are obtained. For finite element analysis, the cubic Hermitian polynomials are utilized as shape functions and $16{\times}16$ stiffness matrix for curved beam elements and $14{\times}14$ stiffness matrix for straight beam elements are evaluated, respectively. In order to illustrate the accuracy of this study, analytical and numerical results for lateral buckling problems of circular arch are presented and compared with available analytical solutions.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1440-1463
• /
• 2018

The Wagner coefficient is a key parameter used to describe the inelastic lateral-torsional buckling (LTB) behaviour of the I-beam, since even for a doubly-symmetric I-section with residual stress, it becomes a monosymmetric I-section due to the characteristics of the non-symmetrical distribution of plastic regions. However, so far no theoretical derivation on the energy equation and Wagner's coefficient have been presented due to the limitation of Vlasov's buckling theory. In order to simplify the nonlinear analysis and calculation, this paper presents a simplified mechanical model and an analytical solution for doubly-symmetric I-beams under pure bending, in which residual stresses and yielding are taken into account. According to the plate-beam theory proposed by the lead author, the energy equation for the inelastic LTB of an I-beam is derived in detail, using only the Euler-Bernoulli beam model and the Kirchhoff-plate model. In this derivation, the concept of the instantaneous shear centre is used and its position can be determined naturally by the condition that the coefficient of the cross-term in the strain energy should be zero; formulae for both the critical moment and the corresponding critical beam length are proposed based upon the analytical buckling equation. An analytical formula of the Wagner coefficient is obtained and the validity of Wagner hypothesis is reconfirmed. Finally, the accuracy of the analytical solution is verified by a FEM solution based upon a bi-modulus model of I-beams. It is found that the critical moments given by the analytical solution almost is identical to those given by Trahair's formulae, and hence the analytical solution can be used as a benchmark to verify the results obtained by other numerical algorithms for inelastic LTB behaviour.