• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.270-273
• /
• 2003

The characteristic of constant volume micro combustor was investigated experimentally. The shape of micro combustor was cylindrical and has row aspect ratio or has relatively large diameter compared with chamber height. Diameter and chamber height was varied to investigate the geometric effect of combustor on the flame propagation. Diameter of 15 mm and 7.5 mm was designed while chamber height was designed to be 1mm, 2mm, and 3mm. The effect of initial pressure was also investigated parametrically from 1bar to 3bar. The gas used in this study was stoichiometric mixture of methane and air. The maximum pressure achieved in down scaled combustors was lower than that of conventional combustor because heat loss to wall was dominant as expected. The maximum pressure responded favorably with the change of height of combustor and the initial pressure, the maximum pressure was also increased. The flame propagation was possible when the specific condition was satisfied. Although the quenching distance of stoichiometric mixture of CH4 and Air is 2.5 mm, the flame could propagate even under quenching distance as the initial pressure increased.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.1
• /
• pp.99-106
• /
• 2010

A vertical datum requires an origin, which is a point on the Earth's surface where the height of the point is a defined value(26.6871m). From this origin point, heights (height differences) can be measured to any other point using standard leveling and gravity measurement procedures. However, the leveling network over the Korea bas been established by using the normal gravity instead of the actual gravity values, and the heights for the points are published by National Geographic Information Institute (NGII). This may cause height for especially in the area where high-relief mountains are dominant. Therefore, the height errors caused by using normal gravity instead of actual gravity values are analyzed in this study. Then, the differences between the orthometric heights and the published heights, i.e., normal orthometric height are analyzed.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.2
• /
• pp.173-179
• /
• 2011

This study aims to analyse difference in biomechanical factors between dominant legs and recessive ones according to muscular imbalance during drop landing targeting talented children in sports. The subjects of the study were ten primary students who are attending to Sports Program for Talented Children organized by C university (age: $12.28{\pm}0.70$ year, height: $1.52{\pm}0.11$ m, and weight: $45.2{\pm}4.9$ kg). Strength legs were classified into dominant side and strengthless legs were classified into non-dominant legs. For three-dimensional analyses of the data collected, 6 video cameras(MotionMaster200, Visol, Korea) were used. To analyse ground reaction force, two force platforms(AMTI ORG-6, MA) were used and to analyse electromyograghy a 8-channeled wireless Noraxon Myoresearch made in USA was used at 1000 Hz for sampling. As a result, it was discovered that the dominants legs controlled knee bending motions more stably than strengthless legs as the maximum vertical ground reaction force was significantly high in dominant legs(p<.05), and joint moment of knee joints of the dominant legs was high(p<.05). Therefore, this study suggested that injury prevention program focusing on muscular balance as well as the existing sports programs for talented children should be developed based on results of the study and it is expected that the results will be useful for improvement of sports programs for talented children.

• Electrolytes & blood pressure
• /
• v.16 no.2
• /
• pp.23-26
• /
• 2018

A 22-year-old male patient was diagnosed with autosomal dominant polycystic kidney disease (ADPKD). He received conservative treatment with an angiotensin-converting enzyme inhibitor. Two years later, oral therapy, consisting of 60 mg tolvaptan per day, was initiated. Compared with height-adjusted total kidney volume, the rate of kidney growth reduced significantly from 7.33% to 0.66% annually, since commencement of the tolvaptan therapy. The liver enzyme profile and serum sodium level and osmolality were constantly within normal ranges. In Korea, this is the first reported case of a patient with ADPKD who received tolvaptan treatment for more than 1 year. This case demonstrates that long-term tolvaptan treatment appears to be safe, well tolerated, and effective for ADPKD.

• Steel and Composite Structures
• /
• v.49 no.6
• /
• pp.685-699
• /
• 2023

In recent years, Carbon Fibre Reinforced Plastic (CFRP) strengthening is found to be one of the best methods to strengthen steel structures. The fibrous bond can also influence the vibration characteristics of the strengthened element apart from its static strength enhancement property. The main objective of this study is to understand the influence of CFRP strengthening on the dynamic Behaviour of Thin-Webbed Castellated Beams (TWCBs). A detailed experimental investigation was carried out on five sets of beams with varying parameters such as domination of shear (Shear Dominant, Moment Dominant and Moment and Shear Dominant), sectional classification (Plastic and Semi-compact) and perforation geometries (h_o/d_wratio 0.65 and e/h_o ratio 0.3). Free vibration analysis was carried out by exciting the simply supported TWCBs with an impact force generated by a ball dropped from a specific height. Logarithmic decrement method was used to obtain the damping ratio and natural frequencies of vibration were found by Fast Fourier Transform (FFT). Natural frequency showed an increase in a range of 10.5 - 55% for the different sets of castellated beams. An increase of 62.30% was noted in the damping ratio of TWCBs after strengthening which is an indication of improvement in the vibration characteristics of the beam.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.841-844
• /
• 1997

Sandwich structure is widely used in various fields of industry due to its excellent strength and stiffness compared with weight. We studied the buckling and bending behavior with respect to the variation of design parameters such as length, height, and thickness of honeycomb sandwich core. We found that as the density and the thickness of core become higher, the value of critical bucking load increased significantly. We found that the effect of bending stress due to critical buckling load resulted in high bending stress and the value of bending stress decreased in half according to the increase of length of core. The effect by bending stress is dominant above the portion of the intersection line between bending stress and the effect of buckling is dominant below the potion of it. We could get proper thickness ratio and density of core according to applied load conditions.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.240-242
• /
• 2008

In the present article, we analyze airborne Pi-SAR (Polarimetric-Interferometric SAR) X-band images of ocean waves around the Miyake Island at approximately 180 km south from Tokyo, Japan. Two images of a same scene were produced at approximately 40 min. interval from two directions at right angles. One image shows dominant range travelling waves, but the other image shows a different wave pattern. This difference can be caused by the different image modulations of RCS and velocity bunching. We have estimated the dominant wavelength from the image of range waves, and from the wave phase velocity computed from the dispersion relation (though no wave height data were available), the image intensity is computed by using the velocity bunching model. The comparison of the result with the second image at right angle strongly suggests the evidence of velocity bunching.

• Korean Journal of Plant Resources
• /
• v.23 no.3
• /
• pp.242-247
• /
• 2010

This study was carried out to elucidate the effect of mulching materials on the growth of Chinese chive (Allium tuberusum Rottler) and weed control. Chinese chive was grown under five mulching materials, pine leaf, oak leaf, rice straw, rice hull and sawdust, at the Experimental Farm of Chungbuk National University from June 20, 2009 to September 30, 2009. Amaranthus mangostunus, Digitaria sanguinalis, Portuclaca. oleracea, Echinochioa crus-galli var. frumetacea and Setaria viridis were dominant weeds. Both pine and oak leaves were significantly effective mulching materials in terms of weed control indices in both nursery and field. Soil moisture contents were 1.2~3.7% higher in mulching, especially in oak leaf mulching. Mulching with pine leaf significantly increased plant height, sheath length, leaf length, bulb-, root- and leaf-weights and yield of Chinese chive, but there were no significant differences among the other mulching materials although better than those in non-mulching.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.955-959
• /
• 2004

The effects of conduction band offset on 2 dimensional electron gas (2DEG) in N-InAlAs(AlAsSb)/InGaAs/InAlAs (AlAsSb) metamorphic heterostructures (MMHS) are studied. A combination of the Shubnikov-deHaas oscillations and the Hall measurements is used to investigate the electron transport properties of these structures. The mobility in the second subband is higher than that in the first subband in all heterostructures. This is attributed to the fact that electrons in the first subband we, on average, closer to the interface and are therefore scattered more strongly by ionized impurities. The results suggest that intersubband scattering rate is more dominant in structures with higher conduction band offset whereas alloy scattering is found to be more dominant in the higher band offset system.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.6
• /
• pp.400-404
• /
• 2018

A metal 3D printer has been developed on its own to electrodeposit the localized area. Nozzles were used to selectively laminate the electrolytic plating method. To analyze the factors affecting the deposition, the stack height, thickness and surface roughness were experimentally analyzed according to the current density and the temperature of the electrolyte. Electrolytic temperature and current are electrodeposited when the deposition conditions are dominant over the etching conditions, but the thickness is kept constant. On the contrary, when the etching conditions are dominant, the electrodeposited shape is rather the etched. As a result, the uniformity of surface quality and electrodeposition rate could be improved by conducting experiments under constant conditions of electrolyte temperature and current density.