• 한국항공우주학회지
• /
• 제31권7호
• /
• pp.9-14
• /
• 2003

본 연구에서는 다중블록 격자를 병렬화 하기 위해서 다중블록/다중영역분할 기법을 제안하였다. 이 방법은 각 블록을 사용하고자 하는 프로세서의 개수만큼 나눔으로써 전체 프로세서에 대해서 균일한 로드 밸런싱을 유지할 수 있는 장점이 있다. 영역분할 기법에 따른 병렬화 효율 및 속도 향상률을 비교하기 위해서 다중블록/단일 영역분할 기법과 다중블록/다중 영역분할 기법을 서로 비교 하였으며, 블록간의 격자수가 크게 다른 경우 다중영역 분할 기법이 로드 밸런싱에 있어서 보다 안정적임을 확인 할 수 있었다. 또한 이를 CFDS에 적용함으로써 다중블록 다중영역분할 기법의 효용성을 검증하였다. 3차원 계산의 경우 프로세서 16개를 사용하는 경우 약 12배의 속도 향상률을 보였으며, 다중블록을 병렬화 하는데 있어서 다중블록/다중영역 분할 기법이 효율적인 도구가 될 수 있음을 보였다.

• 미생물학회지
• /
• 제39권2호
• /
• pp.67-75
• /
• 2003

비교유전체학의 주요 주제 중 유전자서열을 분류하고 단백질기능을 예측하는 연구가 있으며, 이를 위해 단백질 구조, 공통서열 및 바인딩 위치 예측등의 방법과 함께, 전유전체 서열에서 구해지는 유사도 그래프를 분석해 상동유전자를 검색하는 계산학적인 접근방법이 있다. 유사도그래프를 사용한 방법은 서열에 대한 기존 지식에 의존하지 않는 장점이 있지만 유사도 하한값과 같은 주관적인 임계값이 필요한 단점이 있다. 본 논문에서는 반복적으로 그래프를 분해하는 이전의 방법을 일반화시켜, 유사도 그래프에 기반한 유전자 서열군집분석 방법론과 객관적이고 안정적인 파라미터 임계값 계산 방법을 제안한다. 제시된 방법으로 알려진 미생물 유전체 서 열을 분석하여 이전의 방법인 BAG 알고리즘 결과와 비교했다.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.539-542
• /
• 2003

A motor is the workhorse of our industry. The issues of preventive and condition-based maintenance, online monitoring, system fault detection, diagnosis, and prognosis are of increasing importance. Different internal motor faults (e.g., inter-turn short circuits, broken bearings, broken rotor bars) along with external motor faults (e.g., phase failure, mechanical overload, blocked rotor) are expected to happen sooner or later. This paper introduces the fault detection technique of induction motors based upon the stator current. The fault motors have rotor bar broken or rotor unbalance defect, respectively. The stator currents are measured by the current meters and stored by the time domain. The time domain is not suitable to represent the current signals, so the frequency domain is applied to display the signals. The Fourier Transformer is used for the conversion of the signal. After the conversion of the signals, the features of the signals have to be extracted by the signal processing methods like a wavelet analysis, a spectrum analysis, etc. The discovered features are entered to the pattern classification model such as a neural network model, a polynomial neural network, a fuzzy inference model, etc. This paper describes the fault detection results that use wavelet decomposition. The wavelet analysis is very useful method for the time and frequency domain each. Also it is powerful method to detect the features in the signals.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.555-561
• /
• 2012

Empirical Mode Decomposition(EMD)을 통한 Hilbert Huang Transform(HHT)은 시간-주파수 영역분석 방법 중 하나로 기존의 다른 분석 방법에 비해 비선형, 비정상 신호를 해석 가능하다는 등 여러가지 이점이 있다. 그러나 인접한 주파수를 분별하기 힘들고 잡음에 취약하다는 결점이 있다고 알려져 있다. 본 논문에서는 HHT와 정상신호 분석에 효과적인 Short-Time Fourier Transform(STFT)을 비교하여 각 방법의 장 단점을 분석하고 Rijke 튜브 실험에서 얻은 열음향학적 불안정 데이터에 적용하여 잡음에 취약한 점을 보완한 Improved HHT와 비교한다. 그 결과, EMD를 이용한 Original HHT보다 EEMD를 이용한 Improved HHT가 잡음의 영향을 적게 받아 보다 정확한 신호분석이 가능하다는 것을 알 수 있었다.

• Structural Engineering and Mechanics
• /
• 제20권2호
• /
• pp.225-239
• /
• 2005

Applications of the Trefftz boundary element method (BEM) to anti-plane electroelastic problems are presented in this paper. Both direct and indirect methods with domain decomposition are discussed in details. Each crack is treated as semi-infinite thin slit defined in a subregion, for which a particular solution of the anti-plane problem, satisfying exactly the crack-face condition, is derived. The stress intensity factors defined at each crack tip can be directly computed from the coefficients of the particular solution. The performance of the proposed formulation is assessed by two examples and comparison is made with results obtained by other approaches. The Trefftz boundary element approach is demonstrated to be suitable for the analysis of the anti-plane problem of piezoelectric materials.

• 대한기계학회논문집A
• /
• 제31권7호
• /
• pp.739-746
• /
• 2007

Recently, models in STL files are widely used in reverse engineering processes, CAD systems and analysis systems. However the models have poor geometric quality and include only triangles, so the models are not suitable for the finite element analysis. This paper presents a general method that generates finite element mesh from STL file models. Given triangular meshes, the method estimates triangles and makes clusters which consist of triangles. The clusters are merged by some geometric indices. After merging clusters, the method applies plane meshing algorithm, based on domain decomposition method, to each cluster and then the result plane mesh is projected into the original triangular set. Because the algorithm uses general methods to generate plane mesh, we can obtain both tri and quad meshes unlike previous researches. Some mechanical part models are used to show the validity of the proposed method.

• Smart Structures and Systems
• /
• 제10권4_5호
• /
• pp.459-470
• /
• 2012

This paper summarizes a study for the modal analysis and model updating conducted using the monitoring data obtained from the Canton Tower of 610 m tall, which was established as an international benchmark problem by the Hong Kong Polytechnic University. Modal properties of the tower were successfully identified using frequency domain decomposition and stochastic subspace identification methods. Finite element model updating using the measurement data was further performed to reduce the modal property differences between the measurements and those of the finite element model. Over-fitting during the model updating was avoided by using an optimization scheme with a regularization term.

• Smart Structures and Systems
• /
• 제10권4_5호
• /
• pp.393-410
• /
• 2012

The 610 m high Canton Tower (formerly named Guangzhou New Television Tower) is currently considered as a benchmark problem for structural health monitoring (SHM) of high-rise slender structures. In the benchmark study task I, a set of 24-hour ambient vibration measurement data has been available for the output-only system identification study. In this paper, the vector autoregressive models (ARV) method is adopted in the operational modal analysis (OMA) for this TV tower. The identified natural frequencies, damping ratios and mode shapes are presented and compared with the available results from some other research groups which used different methods, e.g., the data-driven stochastic subspace identification (SSI-DATA) method, the enhanced frequency domain decomposition (EFDD) algorithm, and an improved modal identification method based on NExT-ERA technique. Furthermore, the environmental effects on the estimated modal parameters are also discussed.

• Structural Engineering and Mechanics
• /
• 제61권2호
• /
• pp.267-274
• /
• 2017

In this study was investigated of possibility using the recorded micro tremor data on ground level as ambient vibration input excitation data for investigation and application Operational Modal Analysis (OMA) on the bench-scale earthquake simulator (The Quanser Shake Table) for model steel structures. As known OMA methods (such as EFDD, SSI and so on) are supposed to deal with the ambient responses. For this purpose, analytical and experimental modal analysis of a model steel structure for dynamic characteristics was evaluated. 3D Finite element model of the building was evaluated for the model steel structure based on the design drawing. Ambient excitation was provided by shake table from the recorded micro tremor ambient vibration data on ground level. Enhanced Frequency Domain Decomposition is used for the output only modal identification. From this study, best correlation is found between mode shapes. Natural frequencies and analytical frequencies in average (only) 2.8% are differences.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 춘계 학술대회논문집
• /
• pp.123-127
• /
• 2005

The numerical analyses of the complicated flows are widely attempted in these days. Because of the enormous demanding memory and calculation time, parallel processing is used for these problems. In order to obtain calculation efficiency, it is important to choose proper domain decomposition technique and numerical algorithm. In this research we enhanced the efficiency of the CFDS code developed by ADD, using parallel computation and newly developed numerical algorithms. For the huge amount of data transfer between blocks non-blocking method is used, and newly developed data transfer algorithm is used for non-aligned block interface. Recently developed RoeM scheme is adpoted as a spatial difference method, and AF-ADI and LU-SGS methods are used as a time integration method to enhance the convergence of the code. Analyses of the flows around the ONERA M6 wing and the high angle of attack missile configuration are performed to show the efficiency improvement.