• Membrane Journal
• /
• v.29 no.5
• /
• pp.292-298
• /
• 2019

The purpose of this study was to improve the desalination performance by using split electrodes in the capacitive desalination process. The experiment was carried out by measuring the desalination efficiency of the NaCl aqueous solution according to the partitioning of the electrode at 20 mL/min flow rate, 1.2 V, 3 min adsorption conditions, and -1 V, 1 min desorption conditions. The desalination efficiency for the non-divided electrodes with a surface area of $146cm^2$ reached 40% while the divided electrode with a surface area of $133cm^2$ showed a desalination efficiency of 57%. The desalination efficiency of the same split electrode was 49% at 2 cm divided interval and 57% at 1cm divided interval. The desalination efficiency of the split electrode was higher than that of the normal CDI and narrower divided intervals increased the performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.6
• /
• pp.1103-1108
• /
• 2010

A grounding electrode has the transient grounding impedance characteristics against lightning surges. So the performance of grounding electrodes should be evaluated as a grounding impedance as well as the ground resistance. The frequency-dependent grounding impedance is varied with the shape and size of grounding electrode and is divided into both inductive and capacitive behaviors. This paper presents a theoretical analysis for the grounding impedance determined by the size of grounding electrode using the distributed parameter circuit model. EMTP and Matlab programs were used in calculating the frequency-dependent grounding impedances of vertical grounding electrodes. It was found that the frequency-dependent grounding characteristics of vertical grounding electrodes are characterized by the distributed parameters which are changed in the dimension of grounding electrodes.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1140-1142
• /
• 1995

The transformer is fabricated with two piezoelectric vibrator with the divided electrodes and adhesive insulator. We applied the electric input to the driving vibrator in parallel and connect the output voltage to the generating vibrator in series to the resistor load near its fundamental resonance frequency. Then we investigate output voltage in series twice as large as in parallal. Moreover we investigate the load characteristics at resonance frequencies under various resistor and the frequency characteristics near the resonance frequency under no load. Its equvalent circuit is derived from the Mason's model of a thickness-driven piezelectric vibrator. By its equevalent circuit, symbolic expressions for input impedances, voltage ratios, resonance frequencies, and bandwidths have been derived. The values calculated from those symbolic exprssions are shown to agree well with the measurement values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.270-273
• /
• 1996

This paper describes a type of piezoelectric transformer with improved design principles. It consists of a thin rectangular piezoelectric ceramic plate having two input electrodes and one output electrode. The length of each input and output electrode is nearly one third of that of piezoelectric transformer itself. In the driving section, the ceramic plate is poled in the thickness direction reversely with each other, and has electrodes on both main faces. The electric input near its fundamental resonance frequency is applied to the driving section in parallel and the output voltage from the generating section is connected to the resistor load. Its equivalent circuit is derived from the Mason\`s model. The frequency characteristics near the resonance frequency under no load have been investigated. Moreover, using this piezoelectric transformer we measured the LCD backlight characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.881-885
• /
• 2004

We report a method for making a device on which semi-conducting single-walled carbon nanotubes are attached selectively between two metal electrodes. This method is divided two processes. First we can connect a rope of single-walled carbon nanotubes(SWNTs) between two electrodes using the electric field. But a SWNTs' rope obtained by the first process was composed of a few of metallic and semi-conducting SWNTs together. The second process is to burn the metallic and semi-conducting nanotubes through applying a voltage. As a result, we can obtain a semi-conducting SWNT device. To make the patterned electrodes, we deposited $SiO_2$(150nm) on a wafer. After then, we made a patterned samples with Ti(200 $\AA$)/Au(300$\AA$). We empirically obtained a electric condition 0.66 $V_{pp}$ /${\mu}{\textrm}{m}$@5MHz. From this result, we verified that most of current go through the metallic nanotubes in this device. When we apply DC voltage between two electrodes, the metallic carbon nanotubes are burnt. Finally, we can obtain a semi-conducting nanotube device which we desire to make. We got the I-V characteristic graph which has shown the semi-conducting property. We hope to apply to the various applications using this selective semi-conducting carbon nanotube deposition method.ethod.

• Journal of Sensor Science and Technology
• /
• v.22 no.6
• /
• pp.428-432
• /
• 2013

This paper described the development of electrostatically driven peristaltic micropump. The proposed micropump consists of a flexible membrane and a single chamber which electrodes are inserted. The single chamber is divided into smaller cells by the electrodes. The fabricated micropump was operated with four electrodes in the membrane and a various phase sequencing actuation. We studied the changes in the flow rate corresponding to the actuating signal applied to the micropump under the zero hydraulic pressure difference between lnlet port and outlet port. The pump was operated from 60 to 130 V. Whereas the maximum flow rate in basic actuating signal is about 83 ${\mu}1/min$ at 15 Hz, the maximum flow rate in optimized actuating signal is about 114 ${\mu}l/min$ at 10 Hz.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1519_1520
• /
• 2009

This paper investigates forces on a charged particle used in the e-paper application. The particles were inserted into the pixels and according to the applied voltage, particles moves up or down to the electrodes. So, to design the e-paper, the force analysis is very important for the stable operation of e-paper. For these purposes, we divided forces into 4 different forces and numerically evaluated each force. From the simulation results, we confirmed that the minimum voltage to detach the particle from the bottom electrode can be obtained for the given condition.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.301-306
• /
• 2001

Electro-Rheological (ER) fluid is applied to a controllable squeeze film damper (SFD) for stabilizing a flexibly supported rotor system. ER fluid is a class of functional fluid whose yield stress varies according to the applied electric field strength, which is observed as viscosity variation of the fluid. In applying ER fluid to a SFD, a pair of rings of the damper can be used as electrodes. When the electrodes are divided into a horizontal pair and a vertical one, the SFD can produce damping force in each direction independently. A prototype of the directionally controllable SFD was constructed and its performance was experimentally and numerically investigated in the present work.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.256-261
• /
• 2000

Electro-Rheological(ER) fluid is applied to a controllable squeeze film damper(SFD) for stabilizing a flexible rotor system. ER fluid is a class of functional fluid whose yield stress varies according to the applied electric field strength, which is observed as viscosity variation of the fluid. In applying ER fluid to a SFD, a pair of rings of the damper can be used as electrodes. When the electrodes are divided into a horizontal pair and a vertical one, the SFD can produce damping force in each direction independently. A prototype of the directionally controllable SFD was constructed and its performance was experimentally and numerically investigated in the present work.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.10
• /
• pp.1044-1049
• /
• 1990

This paper is concerned with a ceramic filter laminated in the order of piezoelectric vibrator/that insulator/piezoelectric vibrator, and introduces general expressions near the resonant frequency, related with electrical inputs and outputs, gain and phase difference between input and output voltages, resonant frequency, and bandwidth, when the electrodes of the output element are divided by n equi-sections. This paper also shows that those expressions describe well the related experimental phenomena when n=1.