• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1292-1297
• /
• 2000

For dynamic system under the external irregular disturbance, a performance of the controller designed by using of the 'Heo-stochastic control methodology' is investigated by simulations and experiments. MIMO Flexible cantilever beam, sticked with piezoceramics used as a sensor and actuator, under the irregular disturbance at bottom is modelled in physical domain. Dynamic moment equation about the system is derived through both the Ito's stochastic differential equation and Fokker-Planck-Kolmogoroff equation and also system's characteristics in stochastic domain is analyzed. In this study, the controller suppresses the amplitude of the system's moment response to the external disturbance. MIMO PI controller('Heo-stochastic MIMO PI controller') is designed in the stochastic domain and the response characteristics are investigated in the time domain

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.12
• /
• pp.41-47
• /
• 2009

In this paper, authors performed improvement of control characteristics of an attraction type magnetic levitation system. The attraction type magnetic levitation system has an inherent instability in the system, therefore its controller must have not only proportional-integral gain but also differential gain additionally. In this paper, authors were proposed control algorithm using disturbance observer(DOB) on feedback signal. The computer simulation and experiments were performed for its verification.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.267-274
• /
• 2004

In this paper, a new on-line dead-time compensation method is proposed. The output voltage errors due to the dead-time effect is considered as disturbance voltages. The magnitude of the disturbance voltages is estimated using a time delay control technique and the disturbance voltages are calculated using the estimated values, measured currents, and position information. The calculated disturbance voltages are fed to voltage references in order to compensate the dead-time effect. The proposed method is applied to a PM synchronous motor drive system and implemented in a digital manner using a digital signal processor (DSP) TMS320C31. The experiments are carried out for this system to show the effectiveness of the proposed method and the results show the validity of the proposed method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.5
• /
• pp.899-906
• /
• 2020

Motor control requires robust and precise control performance even in the presence of errors in the mathematical model of the motor and disturbances acting on the motor. For robust and precise control, a disturbance observer was designed to estimate the load fluctuation and applied to a back-stepping controller designed as a nominal system. The control performance of the designed system was verified by applying it to the 120 [W] Brushless Direct Current Motor. As a result of the position control and speed control, the disturbance is overcome from the steady state error converges to zero, and asymptotically stable results can be confirmed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.5
• /
• pp.361-368
• /
• 2015

This paper deals with a robust fine seek controller design problem with multiple constraints using a genetic algorithm. A robust $H\infty$ constraint is introduced to attenuate effectively velocity disturbance caused by the eccentric rotation of the disk. A weighting function is optimally selected based on the estimation of velocity disturbance and the estimated minimum velocity loop gain. A robust velocity loop constraint is considered to minimize the variances of the velocity loop gain and bandwidth against the uncertainties of fine actuator. Finally, a robust fine seek controller is obtained by solving a genetic algorithm with an LMI condition and an appropriate objective function. The proposed controller design method is applied to the fine seek control system of a DVD recording device and is evaluated through the experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1326-1329
• /
• 1997

In designing the controller by changing the weighting matrix for the pirpose of satisfying constraints, the physical meaning of weighting matrix may disapperar and the system may not yield best performance because operation condition such as periodic disturbance was not considered. In this paper, the weighting matrix is fixed and controller is designed to minimize the new performance index to reduce the effects of periodic-type disturbances. This method is applied to design the satellite controller to verify the effetiveness.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2783-2786
• /
• 2003

In this paper, the speed controller of permanent-magnet synchronous motor (PMSM) using the RBF neural (NN) disturbance observer is proposed. The suggested controller is designed using the input-output feedback linearization technique for the nominal model of PMSM and incorporates the RBF NN disturbance observer to compensate for the system uncertainties. Therefore the proposed algorithm is robust against the uncertainties of the system. Finally, the computer simulation is rallied out to verify the effectiveness of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.28-31
• /
• 1988

This paper proposes a new linear adaptive position controller of DC servo motor. The proposed method can improve the drive performance and rapidly reject the state error caused by both parameter variations and force disturbance. The structure of this adaptive control method is based multiloop feedback control and model reference control. Simulation results are presented to verify the improved response when parameter variations and load disturbance give relatively significant effects to the servo system.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.363-365
• /
• 2002

The characteristic responds of load respect to various disturbances which can usually be occurred on actual power system is very important to analyze performance and to improve load with high-technology. The disturbance power supply is designed to provide wide range of power to testing load. This device uses PLC technology to dynamic characteristic experiment and CVVF to change frequency. Also this instrument includes data acquisition system to obtain reliable data from experiment.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.129-131
• /
• 2000

The moving vehicle with disturbances has the 6 degree of freedom motion in the pitching, Yawing, and rolling directions of two independent axes. The control system in such a moving vehicle has to perform disturbance rejection. This paper present PID controller with disturbance rejection function, low sensitivity filter and notch filter for bending frequency rejection. The performance of a designed system has been certified by the simulation and experiment and experiment results.