• Geomechanics and Engineering
• /
• v.9 no.3
• /
• pp.397-414
• /
• 2015

Three different applications for monitoring displacements in underground structures using a BOTDR-based distributed optical fiber strain sensing system are presented. These applications are related to the strain measurements of (1) instrumented PVC tube designed to be attached to tunnel side wall and ceiling as a sensor; (2) rock bolts for tunnels; and (3) shotcrete lining under loading. The effectiveness of using the proposed strain sensing system is evaluated by carrying out laboratory tests, in-situ measurements, and numerical simulations. The results obtained from this validation process provide confidence that the optical fiber is able to quantify strain fields under a variety of loading conditions and consequently use this information to estimate the behavior of rock mass during mining activity. As the measuring station can be located as far as 1 km of distance, these alternatives presented may increase the safety of the mine during mining process and for the personnel doing the measurements on the field.

• Journal of the Optical Society of Korea
• /
• v.8 no.4
• /
• pp.168-173
• /
• 2004

Brillouin scattering-based fiber optic sensors are useful to measure strain or temperature in a distributed manner. Since the Brillouin frequency of an optical fiber depends on both the strain and temperature, it is very important to know whether the Brillouin frequency shift is caused by the strain change or temperature change. This article presents a temperature compensation technique of a Brillouin scattering-based fiber optic strain sensor. Both the changes of the Brillouin frequency and the Brillouin gain power is observed for the temperature compensation using a BOTDA sensor system. Experimental results showed that the temperature compensated strain values were highly consistent with actual strain values.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.142-148
• /
• 2004

In this paper, to detect exciting frequency on the latticed fence structure, fiber optic sensor using Sagnac interferometer was fabricated and tested. The latticed structure fabricated with dimension of 180 cm wide and 180 cm high, the optical fiber, 50 m in length, distributed and fixed on the latticed structure. Single mode fiber, a laser with 1,550 m wavelength, and $3{\times}3$ coupler were used. Excited vibration signal applied to the latticed structure from 200 Hz to 1 KHz. The detected optical signals were compared to the detected acceleration signals and analyzed on the time and frequency domain. Based on the experimental results, fiber optic sensor using Sagnac interferometer detected exciting frequency, effectively. This system can be applied to the structural health monitoring system.

• Smart Structures and Systems
• /
• v.21 no.1
• /
• pp.27-35
• /
• 2018

In the water-filling and preloading test, the sensing cables were installed on the surface of steel spiral case and in the surrounding concrete to monitor the strain distribution of several cross-sections by using Brillouin Optical Time Domain Analysis (BOTDA), a kind of distributed optical fiber sensing (DOFS) technology. The average hoop strain of the spiral case was about $330{\mu}{\varepsilon}$ and $590{\mu}{\varepsilon}$ when the water-filling pressure in the spiral case was 2.6 MPa and 4.1 MPa. The difference between the measured and the calculated strain was only about $50{\mu}{\varepsilon}$. It was the first time that the stress adjustment of the spiral case was monitored by the sensing cable when the pressure was increased to 1 MPa and the residual strain of $20{\mu}{\varepsilon}$ was obtained after preloading. Meanwhile, the shrinkage of $70{\sim}100{\mu}{\varepsilon}$ of the surrounding concrete was effectively monitored during the depressurization. It is estimated that the width of the gap between the steel spiral case and the surrounding concrete was 0.51 ~ 0.75 mm. BOTDA based distributed optical fiber sensing technology can obtain continuous strain of the structure and it is more reliable than traditional point sensor. The strain distribution obtained by BOTDA provides strong support for the design and optimization of the spiral case structure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.7A
• /
• pp.712-718
• /
• 2004

We report 1.6 Tb/s (160${\times}$10 Gb/s) WDM transmission over 2,000 km of single mode fiber using distributed hybrid(distributed Raman amplifier＋Erbium-doped fiber amplifier) optical amplifiers. After transmission over 2,000 km of single mode fiber, average optical signal to noise ratios of C/L-band were 20.5 dB, 21.9 dB, respectively. The minimum Q-factors of each band were 14.65 dB (BER=5.8e-8) in C-band, 13.75 dB (BER=5.0e-7) in L-band without forward error correction. We performed 1.6 Tb/s error-free transmission over 2,000 km of single mode fiber using Reed-Solomon (255, 239) forward error correction code.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.337-338
• /
• 2009

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.8
• /
• pp.75-82
• /
• 2013

We propose a fiber grating sensor system for condition monitoring of large scale wind turbine blades. For the feasibility test of the proposed sensor system, a down-scaled wind turbine has been constructed and experimented. Fiber grating sensors were attached on a blade surface for distributed strain and temperature measurements. An optical rotary joint was used to transmit optical signals between the FBG sensor array and the signal processing unit. Instead of broadband light source, we used a wavelength-swept fiber laser to obtain high output power density. A spectrometer demodulation is used to alleviate the nonlinear wavelength tuning problem of the laser source. With the proposed sensor system we could measure dynamic strain and temperature profiles at multi-positions of rotating wind turbine blades.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.823-828
• /
• 2011

We have systematically designed and experimentally demonstrated the opto-electrical predistortion optical transmitter using microwave circuit modelling for reducing the nonlinearity of the distributed-feedback laser diode (DFD-LD). The DFB-LD is analyzed using microwave circuits model based on rate equations. Through the system-level simulation for predistortion method, the optimized characteristics of the RF components in the system are confirmed. The simulated and experimental results show the reduced distortion products. These results are analyzed as the evaluation parameters for the miniaturization and optimization of the opto-electrical predistortion method in radio-over-fiber systems.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.469-472
• /
• 2005

To enhance the scalability of high performance packet switches, a two-stage load-balanced switch has recently been introduced, in which each stage uses a deterministic sequence of configurations. The switch is simple to make scalable and has been proven to provide 100% throughput. However, the load-balanced switch may mis-sequence the packets. In this paper, we propose an algorithm called full frame stuff (FFS), which maintains packet order in the two-stage load-balanced switch and has excellent switching performance. This algorithm is distributed and each port can operate independently.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1680-1686
• /
• 2010

Optical fiber Bragg grating to have the lowest transmitivity at 1549.9nm wavelength was fabricated using a Gaussian distributed KrF Eximer laser of 248nm lasing wavelength and a phase mask of 1.072um period. The proper alignment of an optic setup to fabricate fiber gratings was investigated and the reproductivity of the grating fabrication was examined using the obtained optimum fabrication condition in this experiment.