• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.391-395
• /
• 2013

In this study, zinc oxide (ZnO) nano powder, well known as an UV absorbing material, was synthesized with three synthetic conditions by the hydrothermal method. After ZnO nano powder was surface-modified with various silane coupling agents to improve dispersion property, a dispersion sol was prepared with dispersant for 72 h by the ball-milling of surface-modified ZnO nano powder. The dispersion sol, prepared by modifying the surface of the ZnO nano powder with an average size of about 30 nm using 3-chloropropyl trimethoxy silane, showed an excellent dispersion stability with a high UV-shielding and visible trnasparency.

• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.683-691
• /
• 1993

All the activities and physical properties including surface tension, foaming power, foam stability, emulsifying power, dispersion effect, wettability and solubilization of sodium dodecyl polyoxyethylene ${\alpha}$-sulfo alkanoates aqueous solution were measured and critical micelle concentration was evaluated. Their cmc ebaluated by the surface tension method was $10^{-4}{\sim}10^{-5}mol/{\ell}$, and surface tension of the aqueous solution was decreased to 30~70dyne/cm. The experimental results for foaming power, foam stability, emulsifying power in benzene or soybean oil, dispersion effect in calcium carbonate, wettability and solubilization showed a good and efficient surface active properties, and then it would be expected that these products could be applied as O/W type emulsifier, dispersion agent.

• Elastomers and Composites
• /
• v.37 no.4
• /
• pp.217-223
• /
• 2002

Silica-filled rubber compounds show poor filler dispersion and slow cure characteristics compared to carbon black-filled ones. In general, a silica-filled rubber compound contains silane coupling agent (bis-(3-(triethoxysilyl)-propyl)-tetrasulfide, TESPT) and diphenylguanidine (DPG) to improve the filler dispersion and to make fast cure characteristics. Acrylonitrile-butadiene rubber (NBR) improves the filler dispersion in silica-filled styrene-butadiene rubber (SBR) compounds. In this study, effect of NBR on the properties of silica-filled SBR compounds was investigated. Properties of the compounds which contain NBR without DPG or with small amount of TESPT (Compound A) were compared with those of the compounds which contain TESPT and DPG without NBR (Compound B). Scorch time of Compound A is faster than those of Compound B. Modulus and tensile strength of Comound A are slightly lower than those of Compound B. Traction property of the Comound A is better than that of the Compound B. Addition of NBR leads to reduction of the used amount of TESPT and DPG.

• Journal of Mechanical Science and Technology
• /
• v.15 no.1
• /
• pp.35-43
• /
• 2001

Both tensile and tear properties of short-fiber reinforced Chloroprene rubber have been studied as functions of the fiber aspect ratio and fiber content. Both properties increased when both the fiber aspect ratio and fiber content were increased. The fiber reinforced rubbers exhibited maximum values of these properties at a fiber aspect ratio of about 300. When the fiber aspect ratio exceeds 400, the mechanical properties decreased with the fiber content because of the non-uniform dispersion of fibers. The tensile modulus was compared with the prediction by the Halpin-Tsai equations for randomly oriented cases. A bonding agent was used in the fiber treating process. It was found that the ultimate tensile strength, torque, tearing energy and tensile modulus of the rubbers with treated fibers were much higher than those with untreated ones.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.2
• /
• pp.213-218
• /
• 2013

In this study, epoxy/mica composite was prepared by mixing with mechanical stirrer together with homogenizer, and the effect of amino-type silane coupling agent was also studied. To reduce the viscosity without any decrement of other properties, 1,4-Butanediol diglycidyl ether (1,4-BDGE) as an aliphatic epoxy reactive diluent was introduced to the epoxy/mica composite in order to use as vanish for high voltage motor and generator stator winding. It was confirmed by scanning electron microscopy (SEM) observation that interfacial characteristics between organic epoxy and inorganic mica was modified by coupling agent treatment so that glass transition temperature increased, and tensile strength and electrical breakdown strength increased. The properties were estimated by Weibull statistical analysis and the ac electrical breakdown strength was 20.2% modified by treating silane coupling agent.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.2
• /
• pp.1-4
• /
• 2003

The purpose of this study was to investigate the characteristics of slurry including phosphoric acid for chemical-mechanical planarization of copper and tantalum nitride. In general, the slurry for copper CMP consists of alumina or colloidal silica as an abrasive, organic acid as a complexing agent, an oxidizing agent, a film forming agent, a pH control agent and additives. Hydrogen peroxide (H$_2$O$_2$) is the material that is used as an oxidizing agent in copper CMP. But, the hydrogen peroxide needs some stabilizers to prevent decomposition. We evaluated phosphoric acid (H$_3$PO$_4$) as a stabilizer of the hydrogen peroxide as well as an accelerator of the tantalum nitride CMP process. We also estimated dispersion stability and zeta potential of the abrasive with the contents of phosphoric acid. An acceleration of the tantalum nitride CMP was verified through the electrochemical test. This approach may be useful for the development of the 2$\^$nd/ step copper CMP slurry and hydrogen peroxide stability.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.28-31
• /
• 2003

Copper CMP in terms of the effect of slurry chemicals (oxidizer, corrosion inhibitor, complexing agent) on the process characteristics has been performed. Corrosion inhibitors, benzotriazole (BTA) and tolytriazol (TTA) were used to control the removal rate and avoid isotropic etching. When complexing agent is added with H$_2$O$_2$ 2 wt% in the slurry, the corrosion rate was presented very well. In the case of complexing agent, it was estimated that the proper concentration is 1 wt%, because the addition of tartaric acid to alumina slurry causes low pH and the slurry dispersion stability become unstable. There was not much change of the removal rate. It was assumed that BTA 0.05 wt% is suitable. Most of all, it was appeared that BTA is possible to be replaced by TTA. TTA was distinguished for the effect among complexing agents.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.4
• /
• pp.271-276
• /
• 2012

In this study, the dispersion ability of powder in low viscosity solubilization system that depends on variety and amount of additives and powders was investigated. A PMMA powder shows outstanding dispersion ability because of its repulsive force of partially charged chain and low density of porous structure. A sample, which contains salts, showed better dispersion tendency than a sample without any additives. The dispersion ability was quantity of salts dependent. Furthermore, a sample with divalent ion salts, like $MgSO_4$, showed better dispersion tendency than that of monovalent ion salts, like NaCl or KCl. The reason for the better dispersion tendency was due to the existence of ionized salts around the powders which significantly improves repulsive force between powders and consequently reduces powder aggregation. The sample with chelating agent, like EDTA as an additive, had improved dispersion ability. EDTA chelates and blocks metal cation therefore anion's character is maximized and repulsive force between powders is improved. As a result, salts and EDTA help to improve the powder dispersion ability and the stability of product.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.221-227
• /
• 2019

This study examines the role of the nano- and micro-particle ratio in dispersion stability and mechanical properties of composite resins for SLA(stereolithography) 3D printing technology. VTES(vinyltriethoxysilane)-coated $ZrO_2$ ceramic particles with different nano- and micro-particle ratios are prepared by a hydrolysis and condensation reaction and then dispersed in commercial photopolymer (High-temp) based on interpenetrating networks(IPNs). The coating characteristics of VTES-coated $ZrO_2$ particles are observed by FE-TEM and FT-IR. The rheological properties of VTES-coated $ZrO_2/High-temp$ composite solution with different particle ratios are investigated by rheometer, and the dispersion properties of the composite solution are confirmed by relaxation NMR and Turbiscan. The mechanical properties of 3D-printed objects are measured by a tensile test and nanoindenter. To investigate the aggregation and dispersion properties of VTES-coated $ZrO_2$ ceramic particles with different particle ratios, we observe the cross-sectional images of 3D printed objects using FE-SEM. The 3D printed objects of the composite solution with nano-particles of 80 % demonstrate improved mechanical characteristics.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.13-18
• /
• 2012

A die casting mold releasing agent was prepared from aqueous mixture of powdery carbon black and water soluble natural polymeric materials such as xanthan gum(X-gum) and carboxymethyl cellulose(CMC), which were used as thickening agent as well as curing agent with aldehydes. The suitable concentration of natural polymers for stable dispersion of carbon black in water was 0.25 wt% of X-gum or 1.0 wt% of CMC. When CMC was used less than 1 wt%, the final carbon black disperion showed a rapid phase separation. The adhesion of carbon black releasing agent on glass plate was improved with the amount of crosslinking agent, glutaraldehyde and chain extender, oligosaccharide. However, the affinity of carbon black releasing agent prepared with X-gum was stronger than that with CMC on glass plate. The final carbon black mold releasing agents prepared under our mixing conditions can be applied to the production of castings of high quality with good workability and without worthening evironmental situations.