• Journal of Surface Science and Engineering
• /
• v.52 no.6
• /
• pp.350-356
• /
• 2019

In this study, the effect of mechanical polishing of carbon steel on the tribological properties of manganese phosphate coating on carbon steel has investigated. The microstructure, surface morphology and chemical composition were analyzed by SEM, EDS, and XRD. The surface roughness test was carried out in order to calculate Rvk value by 3D laser microscopy. Also, the tribology property of manganese phosphate coating was tested by ball-on disk. In the results of EDS analysis, coating layer consists of elements such in Mn, P, Fe, and O. XRD showed that (Mn,Fe)₅H₂(PO₄)₄·4H₂O in manganese phosphate coating layer was formed by the chemical reaction between manganese phosphate and elements in carbon steel. As the mechanical polishing degree increased, the friction coefficient was reduced. The rougher the mechanical polishing degree, the better corrosion resistance was obtained.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.51 no.1
• /
• pp.32-39
• /
• 2024

This study evaluated the additive impact of ethylenediamine tetraacetic acid (EDTA) on erythrosine-mediated photodynamic therapy (PDT) against Streptococcus mutans (S. mutans) biofilm by measuring colony-forming units and applying confocal laser scanning microscopy. Fifty-six bovine incisors, free from dental caries or structural defects, were utilized in this study. Dentin specimens were created by cutting with a low-speed diamond disk under a continuous flow of water, resulting in dimensions of 6.0 mm × 3.0 mm × 2.0 mm. The specimens were categorized into 4 groups: Control, EDTA, PDT, and EDTA + PDT. S. mutans ATCC 25175 was employed to establish biofilm on the dentin specimens. A 17% EDTA solution was applied for 1 min. For PDT, erythrosine served as the photosensitizer. Finally, a light-emitting diode source (385 - 515 nm) was employed in this study. The PDT group exhibited a significantly lower bacterial count than both the control and EDTA groups (p < 0.001). The EDTA + PDT group demonstrated a significantly reduced bacterial count compared to the other 3 groups (p < 0.001). This study demonstrated that EDTA enhances the antimicrobial efficacy of PDT on S. mutans biofilm. Even at a low concentration of photosensitizer, the combination of EDTA and PDT yields a significant antibacterial effect.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.49-55
• /
• 2023

Currently, the demand for green technologies toward a sustainable future is rapidly increasing due to growing concern over environmental issues. Methanol is biodegradable and can provide clean combustion to reduce sulfur oxide and nitrogen oxide emissions, and therefore it is a candidate fuel for marine engines. However, the effect of methanol on tribological characteristic degradation should be addressed for methanol-fueled engines. In this study, the methanol addition effects on tribological characteristic degradation is experimentally assessed using a pin-on-disk tribo-tester. Ni-based alloy is used as a target material due to its broad applicability as an engine component material. For a lubricant, engine oil with and without methanol are used. The tests are conducted for up to 10,000 cycles under boundary lubrication while the change in friction force is monitored. Additionally, the wear rate is determined based on laser scanning confocal microscope data. An additional test in which methanol is added at regular intervals is performed with an aim to directly observe its effect on friction. Overall, the friction coefficient increases slightly with increasing methanol concentration. Furthermore, the wear rate of the pin and disk increase significantly with methanol addition. The results also indicate that the friction increases instantaneously with methanol addition at the contacting interface. These findings may be useful for better understanding the methanol effect on the tribological characteristics of Ni-based alloys for methanol-fueled engines with improved performance.

• The korean journal of orthodontics
• /
• v.31 no.6 s.89
• /
• pp.567-578
• /
• 2001

To investigate the difference of Texture exhibited on interproximal enamel surface with each different stripping method and the susceptibility of proximal enamel to demineralization after stripping and the application of a topical fluoride go] and sealant, one hundred human premolars, which were Previously extracted for orthodontic reasons were evaluated by means of Scanning electron microscopy and laser fluorescence. The results were as follows : 1. No matter what the initial stripping instrument was the furrows that resulted from all the stripping methods were not completely removed by careful polishing. 2. Among the enamel surfaces that were treated with three different initial abrasive instruments, followed by the same polishing method (Sof-$Lex^{(r)}$ disks), the enamel surfaces that were treated with 700 crosscut carbide bur showed the smoothest surfaces. 3. The stripped teeth, no matter what the initial stripping instrument was, were less resistant to initial demineralization than untreated teeth. But no difference in caries susceptibility according to differently stripped methods was found (p<(0.001). 4. Teeth treated with APF-gel or sealant were mote resistant to demineralization than those treated without other treatment after stripping (p<0.001). 5. Comparing groups treated with APF-gel to groups treated with sealant, the former was more resistant to demineralization than the tatter (p<0.05). In conclusion, enamel surfaces that were stripped jnterproximally were less resistant to demineralization even though various attempts were made to produce smooth, self-cleaning enamel surfaces. Therefore, additional treatment-sealant or calcifying/ fluoridating solution To the stripped enamel surfaces is recommended.

• Restorative Dentistry and Endodontics
• /
• v.25 no.2
• /
• pp.225-234
• /
• 2000

The purpose of this study was to investigate the distribution and fluorescene intensity of vasoactive intestinal polypeptide(VIP) immunoreactive cells in rat trigeminal ganglion after inferior alveolar nerve axotomy. The animals were divided into normal and two experimental groups. The experimental animals were sacrificed at 14th and 28th day after inferior alveolar nerve axotomy. The trigeminal ganglion was removed and immersed in the 4% paraformaldehyde-0.2% picric acid in 0.1M phosphate buffer. Serial frozon sections about $16{\mu}m$ in thickness were cut with a cryostat. The immunofluorescence staining was performed. The rabbit anti-VIP(1 : 8,000) was used as primary antibody and fluorescene isothiocynate(FITC)-conjugated anti-rabbit IgG(1 : 80) as secondary antibody. The slides were observed under confocal laser scanning microscope. Three-dimensional images were constructed from 9 serial images(each $1{\mu}m$ in thickness) made by automatic optical sectioning. Unprocessed optical sections were obtained and stored on a optical disk. Color picture were printed by a video copy processor. The results were as follows; 1. The appearance of VIP immunoreactive cells in the mandibular part of trigeminal ganglion was 8.79${\pm}$1.99% in normal group and 39.16${\pm}$5.62% in 14 days, 16.25${\pm}$2.39% in 28 days after inferior alveolar nerve axotomy groups. 2. The relative fluorescence intensity of VIP immunoreactive cell bodies in the mandibular part of trigeminal ganglion was 134.40${\pm}$10.39 in normal group and 192.88${\pm}$14.06 in 14 days, 143.10${\pm}$5.02 in 28 days after nerve axotomy groups. Therefore, the relative fluorescence intensity of 14 days after nerve axotomy group was 43.3% higher than intensity of normal group. 3. In optical single section analysis of VIP immunoreactive cell bodies, white cell bodies(moderate fluorescence intensity) were the most abundant in normal and 28 days after nerve axotomy groups. Whereas, in 14 days after nerve axotomy group, red cell bodies(high fluorescence intensity) were the most abundant. 4. In optical serial section analysis of VIP immunoreactive cell bodies, red cell bodies(high fluorescence intensity) were observed in a part of the 9 sections of normal and 24 days after nerve axotomy groups. Whereas, red cell bodies were observed in all of the 9 sections of 14 days after nerve axotomy group. 5. The results indicates that number and fluorescence intensity of VIP immunoreactive cells were increased in the mandibular part of trigeminal ganglion following inferior alveolar nerve axotomy.

• Korean Journal of Food Science and Technology
• /
• v.52 no.6
• /
• pp.670-677
• /
• 2020

To prevent contamination by Campylobacter jejuni during chicken carcass processing, the effect of emulsifiers on C. jejuni inoculated on chicken skin was investigated using confocal laser scanning microscopy. Among the 8 emulsifiers (SWA-10D, L-7D, M-7D, S-1670, L-1695, P-1670, polysorbate 20, polysorbate 80) tested for antimicrobial activity by the paper disk method, 4 emulsifiers (L-7D, L-1695, polysorbate 20, polysorbate 80) were screened further. Emulsifier L-1695 showed the largest clear zone at a concentration of 200 mg/mL. The 4 emulsifiers subjected to primary screening were screened for heat and pH stability. In the contact surface test, emulsifier L-1695 showed the lowest log CFU/㎠ value on both stainless steel and ceramic surfaces. When emulsifier L-1695 was applied via general and electrostatic spray methods, the number of C. jejuni entrapped inside chicken skin follicles was significantly reduced in both methods. In conclusion, the emulsifier L-1695 could be employed as a microbial detachment agent in the chicken carcass processing industry.

• Journal of Periodontal and Implant Science
• /
• v.45 no.2
• /
• pp.38-45
• /
• 2015

Purpose: The purpose of this study was to evaluate the effect of photodynamic therapy (PDT) using erythrosine and a green light emitting diode (LED) light source on biofilms of Aggregatibacter actinomycetemcomitans attached to resorbable blasted media (RBM) and sandblasted, large-grit, acid-etched (SLA) titanium surfaces in vitro. Methods: RBM and SLA disks were subdivided into four groups, including one control group and three test groups (referred to as E0, E30, E60), in order to evaluate the effect of PDT on each surface. The E0 group was put into $500{\mu}L$ of $20{\mu}M$ erythrosine for 60 seconds without irradiation, the E30 group was put into erythrosine for 60 seconds and was then irradiated with a LED for 30 seconds, and the E60 group was put into erythrosine for 60 seconds and then irradiated with a LED for 60 seconds. After PDT, sonication was performed in order to detach the bacteria, the plates were incubated under anaerobic conditions on brucella blood agar plates for 72 hours at $37^{\circ}C$, and the number of colony-forming units (CFUs) was determined. Results: Significant differences were found between the control group and the E30 and E60 groups (P<0.05). A significantly lower quantity of CFU/mL was found in the E30 and E60 groups on both titanium disk surfaces. In confocal scanning laser microscopy images, increased bacterial death was observed when disks were irradiated for a longer period of time. Conclusions: These findings suggest that PDT using erythrosine and a green LED is effective in reducing the viability of A. actinomycetemcomitans attached to surface-modified titanium in vitro.

• Journal of Korean society of Dental Hygiene
• /
• v.20 no.4
• /
• pp.535-543
• /
• 2020

Objectives: The aim of this study was to investigated the surface roughness and change in the amount of adhesion of Streptococcus mutans to the commercial pit and fissure sealant containing cerium oxide nano particles(CNPs). Methods: The CNPs was incorporated into a commercial pit and fissure sealant at 0-4.0 wt%. Disk Specimens (ϕ 10 mm × 2 mm) were prepared by light polymerization the front and back for 40s. Average surface roughness was measured and Streptococcus mutans adhesion was observed under confocal laser scanning microscopy (CLSM) after 24 hour. Data were statistically analyzed by one-way ANOVA and Tukey HSD^a post-hoc test. Results: Difference of the surface roughness(Ra) between groups was not statistically significant in both non CNPs group and CNPs group(p>0.05). In CNPs group, the amount of S. mutans adhesion was significantly different between control group and decreased in order of CNPs 4.0, CNPs 0.5, CNPs 1.0 and CNPs 2.0(p<0.05). Conclusions: Within the limitation of this study, these aspects of oral bacteria performances suggest potential usefulness of the CNPs incorporation, especially CNPs 1% and 2%, in pit and fissure sealant for inducing antibacterial effect.

• Restorative Dentistry and Endodontics
• /
• v.24 no.1
• /
• pp.100-115
• /
• 1999

The purpose of this study was to investigate the distribution of calcitonin gene-related peptide containing nerve fibers in rat pulp after dentinl injury by means of immunohistochemistry and confocal laser scanning microscope. The Spague-Dawley rats weighing about 250-300gm were used. The animals were devided into normal control and experimental groups. Experimental animals were sacrified 1, 2, 4, 7, 10, 21days after dentinal injury (dentin cutting, and then acid etching with 35% phosphoric acid) on the maxillary molar teeth. The maxillary teeth and alveolar bone were removed and immersed in the 4% paraformaldehyde in 0.1M phosphate buffer (pH 7.4), then were decalcified with 15% formic acid for 10 days. Serial frozen $50{\mu}m$ thick sections were cut on a cryostat. The rabbit CGRP antibody was used as a primary antibody with a dilution of 1:2000 in 0.01M PB. The sections were incubated for 48 hours at $4^{\circ}C$, and placed into biotinylated antirabbit Ig G as a secondary anti body with dilution of 1:200 in 0.01M PB and incubated in ABC(avidin-biotin complex). The peroxidase reaction was visualized by incubating the sections in 0.05% 3,3 diaminobenzidine tetrahydrochloride containing 0.02% $H_2O_2$. For the confocal laser scanning microscopic examination, Primary antibody reaction was same as immunoperoxidase stainning, but fluorescein isothiocyanate(FITC)-conjugate antirabbit IgG as a secondary antibody was used. The confocal laser scanning microscope was used for the examination. A series of images of optical sections was collected with a 20x objective at $3{\mu}m$ intervals throughout the depth of specimen. FITC fluerescence was registrated through a 488nm and 568nm excitation filter, and images were saved on optical disk. The stereoscopic images and three dimentionnal images were reconstructed by computer software, and then were analyzed. The results were as follows : 1. In normal control group, CGRP containing nerve fibers were coursed through the root with very little branching, and then formed a dense network of terminals in coronal pulp. 2. A slight increase in CGRP containing nerve fibers at 1 and 2day postinjury was noted subjacent to the injury site. In the 4day group, there were an extensive increase in the number of reactive fibers, followed by a partial return toward normal levels at 7~10 day postinjury, and return by 21days. 3. The sprouting of the CGRP containing nerve fibers was evident within 2day after dentinal injury, and by 4days there was a maximal increased, but was decreased at 7days and returned to normal 10~21 day postinjury. 4. In confocal laser scanning microscopic exammination, the distinct distribution pattern and sprouting reaction of CGRP containing nerve fibers were observed in stereoscopic images and three dimentional images. These results suggest that CGRP containing nerve fiber can be important role in the response to dental injury and pain regulation.

• 한국해양학회지
• /
• v.27 no.1
• /
• pp.19-34
• /
• 1992

Marine seismic refraction surveys have been carried out by Korea Institute of Geology, Mining and Materials(KIGAM) since 1984. The recording of refraction data was based on analog instrumentation. Therefore the resolution of refraction data was not good enough to distinguish many layers. The objective of the interpretation of seismic refraction data is the determination of intervals and critically refracted seismic wave propagation velocities through the layers beneath the sea floor. To determine intervals and velocities precisely, the resolution of refraction data should be enhanced. The intent of the study is to improve the quality of shallow marine refraction data by the digital technique using microcomputer- based acquisition and processing system. The system consists of an IBM AT microcomputer clone, an analog-digital(A/D) converter. A mass storage unit and a parallel processing board. The A/D converter has 12 bits of precision and 250 kHz of conversion rate. The magneto-optical disk drive is used for the mass storage of seismic refraction data. Shallow marine seismic refraction surveys have been carried out using the system at 6 locations off Ulsan and Pusan area. The refraction data were acquired by the radio sonobuoy. The refraction profiles have been produced by the laser printer with 300 dpi resolution after the basic computer processing. 5-9 layers were interpreted from digital refraction profiles, whereas 2-4 layers were interpreted from analog refraction profiles. the propagation velocities of sediments were interpreted as 1.6-2.1 km/sec. The propagation velocities of acoustic basement were interpreted as 2.4-2.7 km/sec off Ulsan area, 4.8 km/sec off Pusan area.