• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.530-533
• /
• 2001

Interleaved Dual Boost(IDB) converter can reduce current ripple, switching loss and harmonics without filter in input power line. Moreover, this improve power factor. In this paper, we will use the state average methode and small signal analysis at the Interleaved dual boost converter. 4-type controllers were designed by using control transfer function. The result of these controller simulations is analyzed and proposed a proper controller at IDB

• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.146-162
• /
• 2006

This paper deals with the analysis, design and implementation of an AC-DC Zeta converter in discontinuous current mode (DCM) of operation used for power quality improvement at AC mains in direct torque controlled (DTC) permanent magnet synchronous motor (PMSM) drives. The designed Zeta converter feeds a direct torque controlled PMSM drive system. Modeling and simulation is carried out in a standard PSIM software environment. Test results are obtained on the developed prototype Zeta converter using DSP ADMC401. The results obtained demonstrate the effectiveness of the Zeta converter in improving power quality at AC mains in the PMSM drive system.

• Journal of the Korean Society of Safety
• /
• v.18 no.3
• /
• pp.46-53
• /
• 2003

For the tensile tests of the F.E.M., microvoids are created by the boundary separation process at the martensite boundary or neighborhood and at inclusions within the fracture. to grow to the ductile dimple fracture. For the case of the M.E.F., microvoids created at the discontinuities of the martensite phase which exists at the grain boundary of the primary ferrite are grown to coalescence with the cleavage cracks induced at the interior of the ferrite, which as a result show the discontinuous brittle fracture behavior. In spite of their similar tensile strengths, the fatigue limit and the notch sensitivity of the M. E.F. is superior to those of the F.E.M., The M.E.F. is much more insensitive to notch than F.E.M. from the stress concentration factor($\alpha$).

• Journal of Navigation and Port Research
• /
• v.31 no.7
• /
• pp.589-595
• /
• 2007

In the majority of previous studies on deformation of seabed structures using DEM, elements of structures have been assumed that it is composed with uniform materials or received fixed wave force, despite that actual submerged structures are composed with various size materials and influenced by complicated fluid field. The goal of this study is to develop a new model for analysis of seabed structure deformation using discontinuous structures composed with various size materials. As the first phase, a model using DEM and VOF, which can compute the deformation of submerged structures composed with various size materials, such as rubble mound structures, is proposed. A model test is carried out and then the validity of the model is discussed.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.1035-1046
• /
• 2015

This study presents a practical implementation of a multi-mode two-phase interleaved boost converter for fuel cell electric vehicle application. The main operating modes, which include two continuous conducting modes and four discontinuous conducting modes, are discussed. The boundaries and transitions among these modes are analyzed with consideration of the inductor parasitic resistance. The safe operational area is analyzed through a comparison of the different operating modes. The output voltage and power characteristics with open-loop or closed-loop operation are also discussed. Key performance parameters, including the DC voltage gain, input ripple current, output ripple voltage, and switch stresses, are presented and supported by simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.319-320
• /
• 2014

본 논문은 DCM(Discontinuous Conduction Mode)로 동작하는 3상 인터리브드 양방향 DC-DC컨버터를 다룬다. 전류 리플을 줄이기 위해 3상 인터리브드 방식을 이용하였으며 소프트 스위칭 조건을 확보하기 위해 DCM동작을 한다. DCM동작시 스위칭 손실을 분석하고 이를 저감하기 위하여 새로운 스위칭 기법을 제시하며 실험으로 유용성을 입증한다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.255-256
• /
• 2015

본 논문에서는 새로이 제안되는 불연속모드 양방향 부스트-포워드 컨버터를 사용하는 셀 밸런싱 방법을 제안한다. 이 컨버터는 다중입력과 다중출력의 양방향 배터리 충방전을 다루고, 다중직렬 배터리의 전압 셀 밸런싱에 초점을 두었다. 여러 입력 배터리의 전압 차가 나지 않을 때는 부스트 컨버터가 작동하고, 레퍼런스가 되는 입력 배터리와 다른 입력 배터리의 전압이 불균형이 생길 때 포워드 컨버터가 작동하여 밸런싱을 맞추는 새로운 불연속모드 부스트-포워드 컨버터 토폴로지를 제안한다. 전압 불균형 에 따른 밸런싱 조건에 대한 식을 증명하였고, 실제로 80W급 하드웨어를 제작하여 제안된 회로를 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.57-58
• /
• 2015

대용량 분산 발전원이 증가하면서 이러한 대용량 분산 발전을 효율적으로 운전하기 위한 많은 연구가 진행되고 있다. 본 논문에서는 멀티레벨 인버터 토폴로지 중 NPC와 T-type 인버터의 중성점 전압제어와, DSVPWMx(Discontinuous Space Vector Pulse Width Modulation) 방식을 적용하여 두 개의 멀티레벨 인버터에서 발생하는 효율과 제어방식의 차이를 시뮬레이션 하였다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.315-316
• /
• 2015

본 논문에서는 3-레벨 Neutral-Point-Clamped (NPC) 인버터의 DC-Link 중성점 전압 리플을 저감하여 인버터 출력 전압의 품질 신뢰성 향상이 가능한 새로운 Discontinuous Pulse Width Modulation (DPWM) 기법을 제안한다. NPC 인버터에서는 두 개의 커패시터로 이루어진 DC-Link 구조로 인해 상, 하단 DC-Link 커패시터 전압 불평형인 상황에서 DC-Link 중 성점 전압 리플이 발생한다. 중성점 전압 리플 발생 시 출력 전압의 품질을 보장할 수 없으며, 민감한 부하에 손상을 입힐 수 있다. 제안한 DPWM 알고리즘은 DC-Link 커패시터 전압을 조정하는 두 개의 오프셋을 사용하여 중성점 전압 리플을 저감한다. 또한, 시뮬레이션을 통해 본 논문에서 제안한 알고리즘의 타당성을 검증한다.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.356-358
• /
• 1994

In this paper, to alleviate the effect of approximation error and discontinuous variation of the controller parameters, the variable structure control scheme using neural networks is presented. In the proposed method, the variable structure control rules for each local linear models are designed to reject the effect of linearization error caused by linearization of the nonlinear system. And neural network infer approximate controller gains from combination of local linear control gains. The proposed control methods can be used to control nonlinear systems and it has robust characteristic against system parameter variations and external disturbances.