• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.859-864
• /
• 2003

In these days, the deterioration of bridges make it necessary for decks to be replaced and it is inevitable to apply the precast decks to minimize the traffic control induced from the deck placement. This precast deck construction makes the physically discontinuous interface between old and new concrete. Usually, the adhesive force at this interface are ignored. However, for crack behavior and reliable long term behavior, it is required to evaluate the exact value of the cohesive force at the interface. This research investigates the cohesive characteristics at the interface. Four different interface surface conditions are tested and three different methods are used to measure the cohesive strength at the interface. In addition, cohesive characteristic at the surface between precast panels are investigated with different interface surface conditions.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1079-1088
• /
• 1996

Discontinuous ${\gamma}$-LiAlO2 fibers for fiber-reinforcing MCFC matrixes have been produced by the sol-gel process using the centrifugal spinning apparatus of the Rotary type. Gel fibers could be obtained through spinning of stable LiAlO2 complex polymetric sols under the optimum spinning conditions (hollow-disc rotating velocity 9000 rpm sol feeding rate of 4ml/min flowing N2 temperature of 4$0^{\circ}C$ and flowing N2 pressure of 4 bar). It was found that defect free and densified ${\gamma}$-LiAlO2 fibers with the relative density of 98% and the mean diameter of 4.7${\mu}{\textrm}{m}$ were prepared when the spinned fibers were heat-treated to 100$0^{\circ}C$ on the specified heating schedule. in particular the mean diameter and length of fibers could be controlled by the pressure of flowing N2 and the chopping-sieving method respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.364-369
• /
• 1987

It has recently shown that a solenoid valve can be utilized in a hydraulic position-control system by discontinuous control methods. The objective of this study is to investigate the effects of solenoid valves on the response characteristics of a hydraulic position-control system by applying two kinds of discontinued control methods i.e., Simple On-Off (SOF) and Pusating On-Off(POF) controls. Three types of solenoid valves i.e. low-frequency, closed-center type (LF/C), high-frequency, closed-center type (HF/C), low-frequency, tandem-center type(LF/T) were used in this study. Effects of loading conditions and control parameters on the response characteristics were experimentally examined and compared each other. Pressure transients within the actuator were also studied.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.1
• /
• pp.15-18
• /
• 2007

We consider the problem of designing a static output feedback sliding mode control law for linear dynamical systems with mismatched uncertainties in the state matrix. We assume that an output dependent sliding surface guaranteeing the quadratic stability of the sliding mode dynamics is given, the reachability condition is not required to be satisfied globally, and the output feedback sliding mode control law complises both linear and discontinuous parts. We reduce the problem of designing the linear part of the sliding mode control law to a simple LMI problem which offers design flexibility for combining various useful convex design specifications. Our approach does not require state transformation and it can be applied to mismatched uncertain systems.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.438-440
• /
• 1997

This paper proposed a partial resonant switching three-phase high power factor converter using a $PRS^2$(Partial Resonant Soft Switch). The proposed converter has a merit of simple controlled circuit because the input current control DCM(Discontinuous Conduction Mode). And it is improve to input power factor that the snubber capacitor's energy regenerate to the AC source side. This topology is reduced a current/voltage stresses of resonant devices in addition to a partial resonant strategy. The result of simulations with the proposed topology included in this paper.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.394-400
• /
• 2012

In this paper, charging modes of series resonant converter for a high voltage energy storage capacitor are compared in terms of charging time, peak resonant current, normalized peak resonant current and voltage in each operation mode. Operating principles of the full bridge series resonant converter with capacitor load are explained and analyzed in discontinuous and continuous operation mode. Based on the analysis and simulation result, $0.6{\omega}_r$ < ${\omega}_s$ < $0.75{\omega}_r$ and $1.3{\omega}_r$ < ${\omega}_s$ < $1.4{\omega}_r$ are evaluated to the best range of switching frequency for charging of an high voltage energy storage capacitor. 1.8 kJ/s SRC prototype is assembled with TI 28335 DSP controller and 40 kJ, 7 kV energy storage capacitor. Design rules based on the comparative analysis are verified by experiment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.5
• /
• pp.896-901
• /
• 2008

This paper addresses the foot force distribution problem for quadruped robots with a failed leg. The quadruped robot has fault-tolerant straight-line gaits with one leg in locked-joint failure, and has discontinuous motion with respect to the robot body. The proposed method is operated in two folds. When the robot body stands still, we use the feature that there are always three supporting legs, and by incorporating the theory of zero-interaction force, we calculate the foot forces analytically without resort to any optimization technique. When the robot body moves, the conventional pseudo-inverse algorithm is applied to obtain the foot forces for supporting legs. Simulation results show the validity of the proposed scheme.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.131-132
• /
• 2015

현대 사회의 기술 발달에 따라서 회로의 집적도 대비 이용하는 주파수가 매우 높아지고 있다. 즉, 회로의 이용 주파수가 높아짐에 따라서 파장이 신호를 전달하는 전선만큼 짧아져 기존의 회로이론을 기반으로 하는 집중 정수 회로적 관점으로 해석할 수 없다. 따라서 전송선로 이론에 따라 해석하여야 하지만, 최근 전자기기들은 높은 집적도나 여러 모듈(Module)을 종합해서 만들기 때문에 전기적 특성이 일정한 전송선로의 이론을 적용하기가 힘들며, 따라서 이는 불연속을 고려한 전송선로의 분석이 이루어져야 함을 시사한다. 이에 본 논문에서는 전송선로에서 불연속 구간이 존재할 경우 기존의 전송선로 이론을 적용한 전기파라미터 변환에 미치는 영향을 알아보기 위해서 불연속 구간이 존재하는 마이크로 스트립 구조를 설계해 VNA(Vector Network Analyzer)를 이용해서 산란계수(S-Parameter)를 측정 및 분석하였다.

• Journal of the Korean Society of Safety
• /
• v.15 no.4
• /
• pp.15-19
• /
• 2000

The exact estimation of the ductile crack growth in a thin sheet would be needed in part of the commercial transport aircraft industry fields. A 2-dimensional elastic plastic finite element analysis was carried out to simulate a stable crack extension in a thin sheet 2024 aluminium alloy. Two kinds of crack modeling were used to evaluate curves of the stable crack extension. And then CTOA(crack tip opening angle) and CTED(crack tip energy density) were calculated in order to determine whether they can be used as useful crack extension criterions in a thin sheet. Results indicate that stable crack extension behaviors were simulated well and CTED is more admirable even though CTOA also is reasonable as a criterion for a stable crack extension in a thin 2024 aluminium alloy sheet.

• Journal of the Korean Society of Safety
• /
• v.6 no.4
• /
• pp.45-52
• /
• 1991

The purpose of a fatigue crack arrest desing is to prvent a fatigue fracture of machine and structure resulted from unstable crack growth. In all cases of load transfer to second elements such as stringers, doublers or flangers, crack arrest is possible; arrest occuring when the fatigue crack reaches the second element. In the present work, the possibility of crack arrest and the design criterion of fatigue crack arrest in the variable thickness plates are examined numericaiiy by using fatigue crack arrest thresthod $\Delta$K$_{th}$of SA-508 reactor vessel steel and stress intensity factor which was obtained in the previous work as a result of 3-dimensional finite element analysis for CT type variable thickness plates having discontinuous interface.e.