• 한국물환경학회지
• /
• 제28권3호
• /
• pp.418-425
• /
• 2012

Dam construction in a river can change its hydrological pattern and trap sediments, which results in ecological changes in the downstream. It is a common phenomenon in the downstream of dams to have decreased sediment flow and increased periphyton. Artificial floods and sediment application are suggested as mitigation practices in order to simulate natural process of flood; transporting sediment and sloughing periphyton off. In this study the effects of artificial floods on periphyton were examined by applying sand artificially and discharging water from a dam (Yangyang Dam, Korea). The study area has been suffering from turbidity problems caused by shore erosion of the dam. The accumulation of inorganic sediments and increase of periphyton on the river bottom are the major factors of habitat deterioration in the downstream reaches. Artificial flood and artificial addition of sand was performed in summer and the effects were measured. Piles of applied sands were washed off easily by discharge and it enhanced the periphyton sloughing effect. The removal efficiency of periphyton was 50 ~ 80% within the 2 km reach from the dam. In conclusion artificial floods and sand application can be a good mitigation measure for the habitat rehabilitation after a dam construction in streams.

• 한국산업보건학회지
• /
• 제27권4호
• /
• pp.257-268
• /
• 2017

Objectives: This study was conducted to review the Toxic UseReduction Act of Massachusetts, USA, which has been evaluated as a successfulcase of a chemical reduction policy, and to search for ways to introduce it inKorea. Methods: We analyzed the implementation of the TURA by attending TUR Planning Course of the Toxic Use Reduction Institute in Massachusetts and researching the related literature. Results: As TURA took effect, the use of chemicals in Massachusetts was reduced, and cost savings were achieved in workplaces. The success factors for the legislation are considered to be support form the federal and state governments and the active participation of business and civic group. Domestic efforts to reduce toxic substances have already begun, so if the process of TURA is appropriately applied to domestic legislation of chemicals control, it would be expected to produce visible results. Therefore, we reviewed the 'Act on Chemicals Registration and Assessment', 'Act on Chemical Control' and 'Act on the Integrated Control of Pollutant-Discharging Facilities' and sought solution for applying TURA to each piece of legislation. For the first case, 'Toxic or Hazardous Substance List' and 'Establishment of Toxic Use Fee' is applicable. For the second case, 'Annual Toxic or Hazardous Substance Reports' is applicable. For the third case, 'Toxic Reduction Plans' and 'Toxics Use Reduction Institute and 'Toxic Use Reduction Planners' is applicable. Conclusions: The government should take notice appropriateness for the reduction of toxic chemicals and provide financial support. Businesses should invest in technologies that build trust with local communities, improve productivity, and reduce costs. Finally, civic group should cooperate with government and businesses.

• Bulletin of the Korean Chemical Society
• /
• 제29권5호
• /
• pp.974-978
• /
• 2008

Removal of heavy metal ions ($Cd^{2+}$ and $Zn^{2+}$) by electrocoagulation (ECG) was investigated in an acidic condition, which is necessary for re-using or discharging the mediated electrochemical oxidation (MEO) media. Effects of various parameters such as electrolytes, current densities, and electrode materials were examined for a metal-contaminated MEO system using $Fe^{2+}/Fe^{3+}$ pairs as a mediator. It was found that ECG with Al electrodes is greatly affected by the presence of $Fe^{2+}$. [$Cd^{2+}$] and [$Zn^{2+}$] remain constant until [$Fe^{2+}$] reaches a certain concentration level (ca. 10 mM). This preferential removal of $Fe^{2+}$ during ECG with Al electrodes is not alleviated by controlling current densities, potential programs, and solution mixing. ECG with Fe electrodes, on the other hand, resulted in relatively fast removal of $Cd^{2+}$ and $Zn^{2+}$ under coexistence of $Fe^{2+}$, indicative of the different role between $Fe^{n+}$ generated from an electrode and $Fe^{2+}$ initially present in a solution. When ECG was performed with Fe electrodes until [$Fe^{n+}$] became the same as the concentration of initially present $Fe^{2+}$, [$Cd^{2+}$] and [$Zn^{2+}$] were reduced to one-tenth of the initial concentrations, suggesting the possibility of a continuous use of the medium for a subsequent MEO process.

• 한국유체기계학회 논문집
• /
• 제17권1호
• /
• pp.5-11
• /
• 2014

The purpose of this paper is to investigate an analytical approach for opening performance evaluation of the nuclear pressure safety valve based on standard codes such as ASME or KEPIC. It is well-known that safety valve is considered as one of pressure relief valves for protecting a boiler or pressure vessel from exceeding the maximum allowable working pressure. When pressure in a container reaches its set pressure, the safety valve commences discharging the internal fluid by a sudden opening called as popping. Safety valve is usually evaluated by set pressure, full open, blow-down, leakage and flow capacity. The test procedure and technical requirement for performance evaluation is described in international code of ASME code such as BPVC. The opening characteristics of steam safety valve can be analyzed by computational fluid dynamics (CFD) and steam shaft dynamics. First, the flow analysis along opening process is simulated by running the CFD models of the ten types of opening steps from 0 to 100%. As a analysis result, the various CFD outputs of flow pattern, pressure, forces on the disc and mass flow at each simulation step is demonstrated. The lift force is calculated by using the forces applied on disc from static pressure and secondary flow. And, the effect of huddle chamber or control chamber is studied by dynamic analysis based on CFD simulation results such as lift force. As a result, dynamics analysis shows opening features according to the sizes of control chamber.

• 한국수자원학회논문집
• /
• 제32권2호
• /
• pp.153-162
• /
• 1999

본 연구에서는 정지수체에서 다공확산관을 통해 방류된 연직다중의 혼합 및 희석 특성에 대해 규명하였다. 3차원 실험수조에서 실험을 통해 밝혀진 결과는 다음과 같다. 우선 다공확산관의 병합과정을 살펴보면 흐름의 안정조건에 따라 병합거리가 다소 차이가 있기는 하지만 {{{{ { z}_{ } }}}}/{{{{ {l}_{ } }}}}가 대략 3인 지점부터 병합이 시작되어 그 이후에는 평면부력？의 거동에 서서히 가까워짐을 알 수 있다. 최소희석률에 대해 분석해 본 결과, 방류운동량이 지배적인 영역, 천이영역, 그리고 부력이 지배적인 부력류영역으로 나누어 희석률 특성을 표현할 수 있음을 알 수 있었다. 본 연구의 실험결과 다공확산관의 경우 부력류영역의 희석률 상수가 평면확산관에 비해 15% 더 높게 나왔다. 그 이유는 다공확산관의 경우 병합 이전에는 개별의 경계면에서 주변수의 포획이 발생하여 희석이 증대되기 때문이다.

• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.196-196
• /
• 2000

Formation of the weld defect, such as a blowhole and a pit in lap-jointed fillet arc welds has been a serious problem in arc welding of Zn-coated steel sheet. In this study, the relationship among welding conditions, welding materials and defect formation was investigated in order to minimize these defects in the CO₂ welds. In addition, the arc stability of the commercial welding wires was evaluated for revealing their effects on defect formation. Main conclusions obtained are as follows:1) There was no difference between shear tensile strength of the sound welds and that of the welds with blowholes whose diameters are less than 0.5mm. However, the welds with blowholes whose diameters are equal or larger than 0.5mm and pits exhibited tensile strength 10~20% and 30~40% lower than that of the sound welds respectively.2) The optimum welding condition to effectively prevent or reduce the weld defects formation are as follows:- The welding variables of 220A-23V-100cm/min and 120A-190V-30cm/min were recommended for minimizing the weld defects.- The gap between the two sheets at the lap-joint should be controlled to more than 0.2mm- Solid wire was less susceptible to the formation of the weld defects than the flux-cored wire.- The low welding current condition produced less weld defects than the hihg welding current condition.3) One of the reason why the amount of the defect was reduced at the low welding current was the gas discharging by the active agitation of the molten pool, due to an increasing in the number of the short circuit. (Received September 27, 1999)

• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.69-76
• /
• 2000

Formation of the weld defect, such as a blowhole and a pit in lap-jointed fillet arc welds has been a serious problem in arc welding Zn-coated steel sheet. In this study, the relationship among welding conditions, welding materials and defect formation was investigated in order to minimize these defects in the CO₂welds. In addition, the arc stability of the commercial welding wires was evaluated for revealing their effects on defect formation. Main conclusions obtained are as follows: 1) There was no difference between shear tensile strength of the sound welds and that of the welds with blowholes whose diameters are less than 0.5mm. However, the welds with blowholes whose diameters are equal or large than 0.5mm and pits exhibited tensile strength 10∼ 20% and 30∼40% lower than that of the sound welds respectively. 2) The optimum welding condition to effectively prevent or reduce the weld defects formation are as follows: -The welding variables of 220A-23V-100cm/min and 120A-19V-30cm/min were recommended for minimizing the weld defects. -The gap between the two sheets at the lap-joint should be controlled to more than 0.2mm. -Solid wire was less susceptible to the formation of the weld defects than the flux-cored wire. -The low welding current condition produced less weld defects than the high welding current condition. 3) One of the reason why the amount of the defect was reduced at the low welding current was the gas discharging by the active agitation of the molten pool, due to an increasing in the number of the short circuit.

• 한국정밀공학회지
• /
• 제18권12호
• /
• pp.152-158
• /
• 2001

In this paper, we have developed an electro discharge machine for micro drilling driven by a voice coil actuator. Because the voltage signal of the electro-discharging circuit shows a lot of peaks and valleys, the active type low-pass filtering technique is adopted to get the average of the signal. Since the motion of the voice coil is precisely controlled by the error value between the object voltage value and the measured one, it is possible to prevent the mechanical contact between the rotating electrode and the workpiece and to maintain the appropriate machining conditions during the process. The electro-chemical machining technology was also adopted to make small diameter electrodes. Pure water is used as a dielectric. The machining procedure is performed to verify the feasibility of the developed system. It takes about 10 seconds to drill the ${\phi}m$100${\mu}m$ hole to the 100${\mu}m$ thickness stainless steel plate. The machining time depends on the values of the resister and the capacitor. There may exist the optimal values of time constant and the tendency is displayed In the appendix.

• Advances in environmental research
• /
• 제9권2호
• /
• pp.135-150
• /
• 2020

Many industries, such as textiles, chemical refineries, leather, plastics and paper, use different dyes in various process steps. At the same time, these industrial sectors are responsible for discharging contaminants that are harmful and toxic to humans and microorganisms by introducing synthetic dyes into wastewater. Of these dyes, methylene blue dye, which is classified as basic dyes, is accepted as a model dye. For this reason, methylene blue dye was selected in the study and its removal from the water was studied. In this study, two efficient biosorbents were developed from chitosan and sunflower waste, an agro-industrial waste and modified using iron nanoparticles. The biosorption efficiency was evaluated for methylene blue (MB) dye removal from aqueous solution under various parameters such as treating agent, solution pH, biosorbent dosage, contact time, initial dye concentration and temperature. We investigated the kinetic properties of dye removal from water for Chitosan-Sunflower (CS), Chitosan-Sunflower-Nanoiron (CSN). When the wavelength of MB dye was spectrophotometrically scanned, the maximum absorbance was determined as 660 nm. For the core shell biosorbents we obtained, we found that the optimum time for removal of MB from wastewater was 60 min. The pH of the best pH was determined as 5 in the studied pH. The most suitable temperature for the experiment was determined as 30℃. SEM-EDAX, TEM, XRD, and FTIR techniques were used to characterize biosorbents produced and modified in the experimental stage and to monitor the change of biosorbent after dye removal. The interactions of the paint with the surface used for removal were explained by these techniques. It was calculated that 80% of CS and 88% of CSN removed MB in optimum conditions. Also, the absorption of MB dye onto the surface was investigated by Langmiur and Frendlinch isotherms and it was determined from the results that the removal was more compatible with Langmiur isotherm.

• 환경영향평가
• /
• 제28권5호
• /
• pp.483-491
• /
• 2019

파리 협약에 따른 post-2020에 대비하기 위한 환경영향평가(EIA : Environmental Impact Assessment) 측면에서의 온실가스 감축방안을 모색하였다. 2010~2019년 금강유역환경청의 EIA대상사업 중 26건의 환경영향평가서(EIS : Environmental Impact Statement)를 사례분석한 결과로, '온실가스 항목'은 대부분 형식적으로 작성된 것으로 분석되었다. 본 연구에서는 EIA시 '온실가스 항목'의 형식적 평가를 개선하기 위한 방안으로서, 1) EIA대상사업별 온실가스 배출량에 따른 배출부과금 할당, 2) "환경오염시설의 통합관리에 관한 법률"에 근거한 '허가배출기준 설정'에 '온실가스 항목'의 추가, 3)이해당사자들이 EIA대상 개발사업의 초기단계에 참여하는 거버넌스 확립으로 온실가스 감축 등을 제안하였고, 구체적인 내용을 논의하였다.