• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1419-1421
• /
• 2002

Plasma polymerization of thiophene was carried out in a vacuum reactor with capacitively coupled electrode. This paper describes the dependence of molecular structure and electrical properties on the polymerization conditions such as plasma energy, mass flow rate and pressure. The plasma polymerized thiophene films were chracterized by FT-IR spectroscopy and SEM. The IR analysis revealed the thiophene rings are broken by the discharge energy.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.331-337
• /
• 2005

This study aims at evaluation of component performance of a commercial micro gas turbine by detailed measurements of various system parameters. A test facility to measure performance of a micro gas turbine was set up. Performance parameters such as turbine exit temperature, exhaust gas temperature, engine inlet temperature, compressor discharge pressure and fuel flow rate were measured. Variations in measured data and estimated performance parameters were analyzed. In addition to overall engine performance, component characteristic parameters including the turbine inlet temperature, the compressor efficiency, the turbine efficiency, the recuperator effectiveness were estimated. Behaviors of the estimated characteristic parameters with operating condition change were examined.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.11
• /
• pp.1227-1234
• /
• 1990

This study is to figure out the properties of the DC thermal plasma at low pressure. For this purpose, a temperature measurement system utilizing emission spectroscopy has been set up and its measurement method and results have been described. At low pressure, the plasma has shown drastic changes in its appearance. The discharge characteristics under low pressure have been measured and analyzed. The temperature of thermal plasma generated in this research has been ranged from 10, 000 K to 15, 000 K. Temperature has been observed to increase with the flow rate and magnetic field strength. The temperature characteristics at low pressure has been observed to coincide with the reported results.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.1
• /
• pp.121-132
• /
• 2013

The objective of this study is to maintain the same frequency as the electrode material, concentration, duration of decomposition efficiency, power consumption and voltage measurements using a composite catalyst according to the change of process parameters to obtain the optimum state of the process and the maximum decomposition efficiency. In this paper, known as a major cause of air pollution, such as NO, NO2, SO2, frequency, flow rate, concentration, the material of the electrodes, and using TiO2 catalyst reactor with surface discharge caused by discharging the reactor plasma NOx, SOx decompose the harmful gas want to remove.

• Journal of Aerospace System Engineering
• /
• v.8 no.1
• /
• pp.18-23
• /
• 2014

This thesis is simulated a aircraft nose landing gear drop-test. flow rate-to-pressure difference characteristics of damping orifices for a nose landing gear is investigated by CFD analyses. Orifice is kind of poppet valve type. it is simulated pressure drop with variable orifice area. it is simulated landing gear model by using ADAMS with CFD result. It's performance evaluated landing gear drop-test and analyzed the results.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.570-575
• /
• 2005

An efficiency of a refrigeration cycle and a reliability of a compressor can be reduced if a refrigerant including excessive lubricating oil is exhausted from a rotary compressor. Thus, the oil behavior inside the compressor should be analyzed to improve the efficiency. A tested rotary compressor has been manufactured with visualization windows at upper parts in this study to investigate the oil behavior using developed visualization techniques. Discharge pipe with level gage has been visualized to investigate discharged oil amount. The oil behaviors inside the compressor and discharging pipe at various operating conditions have been analyzed. The results of the visualization for the discharging pipe have been compared with those of the upper part to confirm the accuracy.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1400-1402
• /
• 1994

Plasma polymerized thin films was prepared using an interelectrod inductively coupled gas-flow-type reactor. Styrene was chosen as the monomer to be used. This thin films were also delineated by the electron-beam apparatus with an acceleration voltage 30kV, and the pattern in the resist was developed with RIE 80 with argon gas mixture ratio, pressure and RF power. The molecular structure of thin films was investigated by GPC and FT-IR and then was discussed in relation to its quality as a resist. In the case of plasma polymerization, thickness of resist could be controlled by discharge duration and power. Also etch rate is increased as to growing pressure with RIE 80.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.8
• /
• pp.754-763
• /
• 2005

This paper introduces a new concept compressor in which piston orbits in the cylinder having an annular space formed between two concentric circular walls. In this configuration, two gas pockets are formed with $180^{\circ}$ phase difference: one between the wrap of the orbiting piston and the inner cylinder wall and the other between the piston wrap and the outer cylinder wall. This alternating feature of gas compression and discharge processes yields several advantages such as low torque variation and low gas pulsation. Computer simulation program has been developed to evaluate the compressor performance. The volumetric, adiabatic, and mechanical efficiencies of the orbiter compressor are calculated to be $85.6\%,\;97.2\%,\;and\;95.2\%$, respectively, when it is used as an air compressor.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.5 s.38
• /
• pp.14-21
• /
• 2006

In general, the hollow jet valve, the fixed cone valve had been used for the urgency released or maintenance of the flow rate. Nowadays, the butterfly valve, the gate valve are applied in economic performance and operation maintenance more than the hollow jet valve, the fixed cone valve. However, in the case of butterfly valve, it should be required the strict application standard to the cavitation coefficient because the structural axis and disk were situated in pipe channel and the occurring the shock problem by Karman Vortex. Therefore, there were investigated the valve cavitation and accident investigation by field survey to establish the applicable extensibility of the urgency released valve as the preliminary study.

• Journal of Aerospace System Engineering
• /
• v.6 no.2
• /
• pp.13-17
• /
• 2012

In this study the flow rate-to-pressure difference characteristics of short-tube type damping orifices for a aircraft door damper were investigated by CFD analyses. For the verification of the CFD analysis results the actual performance of a door damper was measured and compared with them. and The dynamic response of door damper is Simulated using ADAMS. it's performance is evaluated comparing to the experiment result of door damper.