• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.417-422
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristics were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025 N/m, it is possible to eject stable droplets up to 20 kHz, 4.4 m/s and above 8 pl at the different applied driving waveforms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.61-67
• /
• 2012

The in-wheel motor used in green car was designed and constructed for an electric direct-drive traction system. It is difficult to connect cooling water piping because the in-wheel motor is located within the wheel structure. In the air cooling structure for the in-wheel motor, a outer surface on the housing is provided with cooling grooves to increase the heat transfer area. In this study, we carried out the analysis on the fluid flow and thermal characteristics of the in-wheel motor under the effects of motor speed and heat generation. In order to check the problem of heat release, the analysis has been performed using conjugate heat transfer (conduction and convection). As a result, flow fields and temperature distribution inside the in-wheel motor were obtained for base speed condition (1250 rpm) and maximum speed condition (5000 rpm). Also, the thermo-flow characteristics analysis of in-wheel motor for vehicles was performed in consideration of ram air effect. Therefore, we checked the feasibility of the air cooling for the housing geometry having cooling grooves and investigated the cooling performance enhancement.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.494-504
• /
• 2008

Successful design, construction and maintenance of NATM tunnel demands prediction, control, stability estimation and monitoring of surface settlement, gradient and ground displacement with high accuracy. Back analysis using measured data and forward analysis have been and are indispensable tools to achieve this goal. Sakurai provided the hazard warning levels for assessing the stability of tunnels using the relation of critical strain and apparent Young's modulus. This paper performed the estimation of tunnel stability on construction. Firstly, the apparent Young's modulus concept and back analysis method is introduced for the assessment of tunnel safety during excavation a brief framework. Secondly, this paper deals with case study using "Apparent Young's modulus" and "Back analysis" for the purpose of estimating the stability of NATM tunnel in Korea. Finally, a general method that can be estimated the tunnel stability discussed by a flow chart.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.580-585
• /
• 2004

The purpose of this study is the stability evaluation of soil slope according to inclination of upper natural slope. Upper natural slope breeds loss of slope by inflow in slope of surface water by rainfal1 and f1uctuation of amount of materials in slope through method of cutting slope according to degree of inclination. Basis of standard inclination does not consider of inclination of upper natural slope and is presented uniformly. Therefore, in this study, analyzed stability of inclination of upper natural slope through limit equilibrium analysis. Result is same as following. First, safety factor through limit equilibrium analysis is almost direct decrease when gradient of soil slope is 1:1.2, 1:1.5. However, when gradient of soil slope is 1:1.0, 1:0.7, if sinclination of upper natural slope are $20^{\circ}$, it shows tendency that decrease of safety factor becomes low rapidly. Second, when when gradient of soil slope is fixed, inclination of upper natural slope increase tendency(maximum 3.0 times) that decrease of safety factor.

• ALGAE
• /
• v.24 no.3
• /
• pp.149-161
• /
• 2009

Characteristics of benthic microalgae and sediment properties were investigated for the intertidal flats of Kwangyang Bay, Korea. Sampling stations were selected every 100 m in the intertidal flats from land-side to open ocean at two different sampling sites. Samples were collected in June 2004, July, September, November, February and May 2005. Sediments properties were measured including temperature, water contents, sediment bulk density, nutrient concentrations in porewater. Chlorophyll a concentrations in surface sediment (0.5 cm) were measured and relationships between the chlorophyll a and various sediment properties were analyzed to identify major mechanisms regulating biomass of benthic microalgae in the intertidal flats using simple linear regression analysis. Sediment chlorophyll a concentrations were maximum during winter and minimum during warm seasons ranging from 4.4 mg $m^{-2}\;to\;81.2\;mg\;m^{-2}$. No clear spatial variations were observed for the sediment chlorophyll a in the study sites. Results from regression analysis suggested that benthic microalgae biomass was affected by sediment temperature and nutrients especially ammonium and silicate. Grazing effect was estimated using chlorophyll: pheopigments ratio, indirect indicator of grazing activity, and the positive correlation of the ratio and chlorophyll a implied that microalgae biomass is affected by grazing of zoobenthos although direct measurement of grazing activity is required to determine the importance of top-down controls in the benthic microalgae dynamics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.587-587
• /
• 2013

ZnS is well-known direct band gap II-VI semiconductor, and it attracts intense interest due to its excellent properties of luminescence which enable ZnS to have promising materials for optical, photonic and electronic devices. Especially, the emission wavelength of ZnS falls in the UV absorption band of most organic compoundsand biomolecules, thus it is envisaged that ZnS based devices may find applications in increasingly important fluorescence sensing. We have developed a facile and effective one-step process for the fabrication of single-crystalline and pure-wurtzite ZnS nanostructures possessing sharp band-edge emission at room-temperature having diverse length-to-width ratios. Each of nanostructures was composed of chemically pure, structurally uniform, single-crystalline, and defect-free ZnS. These features not only suppress trap or surface states emission centered at 420 nm, but also enhance UV band-edge emission centered at 327 nm, which give as-synthesized our ZnS nanostructures possible sharp UV emission at room temperature. The reaction medium consisting of mixed solvents such as hydrazine, ethylenediamine, and water as well as proper reaction time and temperature have played an important role in the crystallinity and optical properties of ZnS nanostructures. As-synthesized our ZnS nanostructures possessing sharp UV emission guarantee high potential for both fundamental research and technological applications.

• Journal of Microbiology and Biotechnology
• /
• v.31 no.11
• /
• pp.1519-1525
• /
• 2021

Hexavalent chromium (Cr(VI)) is recognized to be carcinogenic and toxic and registered as a contaminant in many drinking water regulations. It occurs naturally and is also produced by industrial processes. The reduction of Cr(VI) to Cr(III) has been a central topic for chromium remediation since Cr(III) is less toxic and less mobile. In this study, fermentative Fe(III)-reducing bacterial strains (Cellu-2a, Cellu-5a, and Cellu-5b) were isolated from a groundwater sample and were phylogenetically related to species of Cellulomonas by 16S rRNA gene analysis. One selected strain, Cellu-2a showed its capacity of reduction of both soluble iron (ferric citrate) and solid iron (hydrous ferric oxide, HFO), as well as aqueous Cr(VI). The strain Cellu-2a was able to reduce 15 μM Cr(VI) directly with glucose or sucrose as a sole carbon source under the anaerobic condition and indirectly with one of the substrates and HFO in the same incubations. The heterogeneous reduction of Cr(VI) by the surface-associated reduced iron from HFO by Cellu-2a likely assisted the Cr(VI) reduction. Fermentative features such as large-scale cell growth may impose advantages on the application of bacterial Cr(VI) reduction over anaerobic respiratory reduction.

• Geomechanics and Engineering
• /
• v.33 no.2
• /
• pp.121-131
• /
• 2023

Clay sedimentation has been widely analyzed for its application in a variety of geotechnical constructions such as mine tailing, artificial islands, dredging, and reclamation. Chemical flocculants such as aluminum sulfate (Al₂(SO₄)₃), ferric chloride (FeCl₃), and ferric sulfate (Fe(SO₄)₃), have been adopted to accelerate the settling behaviors of clays. As an alternative clay flocculant with natural origin, this study investigated the settling of xanthan gum-treated kaolinite suspension in deionized water. The sedimentation of kaolinite in solutions of xanthan gum biopolymer (0%, 0.1%, 0.5%, 1.0%, and 2.0% in a clay mass) was measured until the sediment height was stabilized. Kaolinite was aggregated by xanthan gum via a direct electrical interaction between the negatively charged xanthan gum molecules and positively charged edge surface and via hydrogen bonding with kaolinite particles. The results revealed that the xanthan gum initially bound kaolinite aggregates, thereby forming larger floc sizes. Owing to their greater floc size, the aggregated kaolinite flocs induced by xanthan gum settled faster than the untreated kaolinite. Additionally, X-ray computed tomography images collected at various depths from the bottom demonstrated that the xanthan gum-induced aggregation resulted in denser sediment deposition. The findings of this study could inspire further efforts to accelerate the settling of kaolinite clays by adding xanthan gum.

• Geomechanics and Engineering
• /
• v.31 no.3
• /
• pp.281-289
• /
• 2022

Bio-CaCO₃ is a blowout environment-friendly materials for soil improvement and sealing of rock fissures. To evaluate the chemical characteristics, shape, size and productivity of soybean urease induced CaCO₃ precipitates (SUICP), experimental studies were conducted via EDS, XRD, FT-IR, TGA, BET, and SEM. Also, the conversion rate of SUICP reaction at different time were determined and analyzed. The Bio-CaCO₃ product obtained by SUICP is comprehensively judged as calcite based on the results of EDS, XRD and FT-IR. The SUICP calcite precipitates are detected as spherical or ellipsoidal particles 3-6 ㎛ in diameter with nanoscale pores on their surface, and this morphology is novel. The median secondary particle size d₅₀ is 39-88 ㎛, indicating the agglomeration of the primary calcite particles. The Bio-calcite decomposes at 650-780℃, representing a medium thermal stability. The conversion rate of SUICP reaction can reach 80% in 24h, which is much more efficient than microbially induced CaCO₃ precipitation. These results reveal the knowledges of SUICP, and further direct its engineering applications. Moreover, we show an economic channel to obtain porous spherical calcite.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.1
• /
• pp.28-34
• /
• 2004

This study was performed to evaluate the characteristics of the carboxymethylated substrate from high reactive autohydrolyzed cellulose (HRC) and those of commercial α-cellulose (CAC) and refiner mechanical pulp (RMP). Saccharification rates of HRC substrate were achieved over 70% with 12 hr hydrolysis, about 90% with 24 hr, and 99.5% with 72 hr. CMCase and avicelase activities of cellulase onozuka were 4.09 ㎛ G/mg·min and 14.0 ㎛ G/mg·min, respectively. There were no any significant changes in cellulase activities with this substrate. The saccharification rates of CAC and RMP were very low, 57% and 38% with 72 hr, respectively. Those lignin-zero autohydrolyzed substrates, HRC and CAC, were highly carboxymethylated at the high alkali concentration, near 30%, for 3 hr. reaction, and resulted in 1.13-1.15 of D.S., besides 0.85 of D.S. from RMP. Water solubilities of carboxymethylated substrates were increased with an increase of D.S., 98-98.5% from HRC and CAC and 31.5% from RMP. RMP which has low specific surface area showed lower water retention values, compared to high values of 435 and 321% from CAC and HRC, respectively. There were no direct relationship between surface area and swelling ratio of the substrates.