• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.3
• /
• pp.159-165
• /
• 2005

The characterization of radiological contamination inside pipes generated during the decommission of a nuclear facility is necessary before pipes can be recycled or disposed. But, existing direct measurements of radioactive contamination level using the survey-meter can not estimate the characteristic of contamination on a local area such as the pipe inside. Moreover, the measurement of surface contamination level using the indirect methods has many problems of an application because of the difficulty of collecting sample and contamination possibility of a worker when collecting sample. In this work, plastic scintillator was simulated by using Monte Carlo simulation method for detection of beta radiation emitted from internal surfaces of small diameter pipe. Simulation results predicted the optimum thickness and geometry of plastic scintillator at which energy absorption for beta radiation was maximized. In addition, the problem of scintillator processing and transferring the detector into the pipe inside was considered when fabricating the plastic detector on the basis of simulation results. The characteristic of detector fabricated was also estimated. As a result, it was confirmed that detector capability was suitable for the measurement of contamination level. Also, the development of a detector for estimating the radiological characteristic of contamination on a local area such as the pipe inside was proven to be feasible.

• Journal of Environmental Policy
• /
• v.8 no.1
• /
• pp.49-72
• /
• 2009

To analyze the direct and indirect $CO_2$ emission structure according to industries in Korea, a hybrid IO table quantifying the section of energy in the IO table is needed. However, the results of the recent researches revealed differences in the total amount of $CO_2$ emission by researchers in addition to significant standard deviation in industrial distribution. This study intends to make comparative analysis of the existing method of making an IO table for energy and environment and presents an improvement scheme to contribute to an improvement in calculation of the total amount of $CO_2$ emission and estimation of the emission by industries in Korea. For this purpose, division was made into use as raw materials of energy and that as fuel and a new hybrid IO table was made by removing confounding factors caused by the product tax and subsidies. As a result, the oil and coal industry emitted 5.2 times less $CO_2$ after removing energy inputted as raw materials from the transaction table than before. The amount of $CO_2$ emission estimated by using the IO table based on basic price was found to be 2.7% less than by using the IO table based on the producer price.

• Asian-Australasian Journal of Animal Sciences
• /
• v.32 no.10
• /
• pp.1573-1579
• /
• 2019

Objective: The research was conducted to determine the digestible (DE) and metabolizable energy (ME) contents as well as the apparent total tract digestibility (ATTD) of nutrients in corn, waxy corn and steam-flaked corn fed to growing pigs. Methods: Eighteen growing pigs with initial body weight of $15.42{\pm}1.41kg$ were randomly allotted to three diets including a corn diet, a waxy corn diet and a steam-flaked corn diet in a completely randomized design. Each treatment contained six replicates. The experiment lasted for 12 days, which comprised 7-d adaptation to diets followed by a 5-d total collection of feces and urine. The energy contents and the nutrient digestibility in three ingredients were calculated using direct method. Results: Compared to normal corn, both the amylose and dietary fiber contents in waxy corn were numerically lower, but the starch gelatinization degree was numerically greater. Moreover, the DE and ME contents as well as the ATTD of neutral detergent fiber and acid detergent fiber (ADF) in waxy corn were significantly greater (p<0.05) than those in normal corn when fed to growing pigs. Furthermore, the steam-flaked corn had greater (p<0.05) DE and ME contents, and ATTD of ether extract and ADF compared to normal corn. Conclusion: Both variety and processing procedure have influence on chemical compositions, energy contents and nutrient digestibility of corn. The waxy corn and steam-flaked corn had greater degree of starch gelatinization and DE and ME contents compared to normal corn when fed to growing pigs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.115-115
• /
• 2015

Many efforts have been devoted on chemical modification of graphene layer to modulate its electrical properties. In the previous report, laser irradiation on the CYTOP (Amorphous Fluoropolymer) covered graphene layer induces chemical modification wherein carbon fluoride is formed on the graphene surface. This results in the insulating I-V characteristics, which have been attracting much research interests on it. However, the direct analytical evidence of the fluoride formation on graphene surface is not yet studied. In this work we investigated what happened on the CYTOP/graphene interface during photon irradiation using spatially resolved photoemission spectroscopy method. It is found that the soft x-ray (614 eV) induces desorption of fluoride atoms from the CYTOP and change di-fluoride form to mono-fluoride. As the photo-induced fluorine desorption is continue strong dipole field generated by initial di-fluoride forms is gradually decreased, resulting in the overall binding energy shift of the C 1s core levels. Both photo-modified CYTOP and CYTOP starts to desorb above $286^{\circ}C$ (~ 0.047 eV), which means that no strong chemical interaction between CYTOP and graphene is established.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.319-324
• /
• 2001

A finite element model for the process of squeeze casting for metal matrix composites (MMCs) in cylindrical mold is developed. The fluid flow and the heat transfer are the fundamental phenomena in the squeeze casing process. To describe heat transfer with solidification of molten aluminum, the energy equation in terms of temperature and enthalpy are applied to two dimensional axisymmetric model which is similar to the experimental system. And one dimensional flow model is employed to simulate the transient metal flow. The direct iteration technique was used to solve the resulting nonlinear algebraic equations. A computer program is developed to calculate the enthalpy, temperature and fluid velocity. Cooling curves and temperature distribution during infiltration and solidification are calculated for pure aluminum. The temperature is measured and recorded experimentally. At two points of the perform inside and one point of the mold outside, thermocouple wire are installed. The time-temperature data are compared with the calculated cooling curves. The experimental results show that the finite element model can estimate the solidification time and predict the cooling process.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.177-181
• /
• 2013

In this paper, silicon solar cells are analyzed regarding power conversion efficiency by changed capacitance in the depletion region. For the capacitance control in the depletion region of silicon solar cell was applied for 10, 20, 40, 80, 160 and 320 Hz frequency band character and alternating current(AC) voltage with square wave of 0.2~1.4 V. Academically, symmetry formation of positive and negative change of the p-n junction is similar to the physical effect of capacitance. According to the experiment result, because input of square wave with alternating current(AC) voltage could be observed to changed capacitance effect by indirectly method through non-linear power conversion (Voltage-Current) output. In addition, when input alternating current(AC) voltage in the silicon solar cell, changed capacitance of depletion region with the forward bias condition and reverse bias condition gave a direct effect to the charge mobility.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.10
• /
• pp.1286-1291
• /
• 2018

In recent years, the proliferation of DER (distributed energy resources) is progressing rapidly. In particular, research on LVDC distribution grid with various advantages has begun. In order to commercialize this LVDC grid, direct current protection method should be established by analysis of DC faults. Recently, the development of HSCB (high-speed circuit breaker) for new ${\pm}750[V]$ LVDC grid has been researched. This paper deals with the calculation of the maximum short-circuit fault current of the HSCB as a part of the development of HSCB for the LVDC distribution grid. First, modeling using PSCAD was carried out for PV array with BESS on the Gochang Power Test Center system. Next, to calculate the rated capacity of HSCB, fault currents were calculated and the characteristics were analyzed through fault simulations. Thus, this study results can help to establish short-circuit capacity calculation of HSCB and protection plan for DC protection relay system.

• Structural Engineering and Mechanics
• /
• v.68 no.1
• /
• pp.1-15
• /
• 2018

In ocean industry, free surface type ART (Anti Roll tank) system has been widely used to suppress the roll motion of floating structures. In those, various obstacles have been devised to obtain the sufficient damping and to enhance the controllability of freely rushing water inside the tank. Most of previous researches have paid on the development of simple mathematical formula for coupled ship-ARTs analysis although other numerical and experimental approaches exist. Little attention has been focused on the use of 3D panel method for preliminary design of free surface type ART despite its advantages in computational time and general capacity for hydrodynamic damping estimation. This study aims at developing a potential theory based hydrodynamic code for the analysis of floating structure with baffled ARTs. The sloshing in baffled tanks is modeled through the linear potential theory with FE discretization and it coupled with hydrodynamic equations of floating structures discretized by BEM and FEM, resulting in direct coupled FE-BE formulation. The general capacity of proposed formulation is emphasized through the coupled hydrodynamic analysis of floating structure and sloshing inside baffled ARTs. In addition, the numerical methods for natural sloshing frequency tuning and estimation of hydrodynamic damping ratio of liquid sloshing in baffled tanks undergoing wave exiting loads are developed through the proposed formulation. In numerical examples, effects of natural frequency tuning and baffle ratios on the maximum and significant roll motions are investigated.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.97-101
• /
• 2004

W $O_{x}$-based semiconductor type thin film gas sensor was fabricated for the detection of N $O_{x}$ by reactive d.c. sputtering method. The relative oxidation state of the deposited W $O_{x}$ films was approximately compared by the calculation of the difference of the binding energy between Ols to W4 $f_{7}$2/ core level XPS spectra in the standard W $O_3$ powder of known composition. As the annealing temperature increased from 500 to 80$0^{\circ}C$, relative oxygen contents and grain size of the sputtered films were gradually increased. As the results of sensitivity ( $R_{gas}$/ $R_{air}$) measurements for the 5 ppm N $O_2$ gas, the sensitivity was 110 and the sensor showed recovery time as fast as 200 s. The other sensor properties were examined in terms of surface microstructure, annealing temperature, and relative oxygen contents. These results indicated that the W $O_3$ thin film with well controlled structure is a good candidate for monitoring and controlling of automobile exhaust.haust.t.t.t.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.230-231
• /
• 2005

As environmental problems are important, automotive industries are developing various techniques to prevent air pollution. One of these is Positive Crankcase Ventilation (PCV) system. It removes blowby gas which includes about 30% hydrocarbon of total generated quantity. In this system, a PCV valve is attached in a manifold suction tube to control the flow rate of blowby gas which generates differently according to various operating conditions of an automotive engine. As this valve is very important, designers are feeling to design it because of both small size and high velocity. For this reason, we numerically investigated to understand both spool dynamic motion and internal fluid flow characteristics. As the results, spool dynamic characteristics, i.e. displacement, velocity, acting force, increase in direct proportion to the magnitude of differential pressure and indicate periodic oscillating motions. And, the velocity at the orifice region decreases according to the increase of differential pressure because of energy loss which is caused by the sudden decrease of flow area at the orifice region and the increase of flow volume in the front of spool head. Finally, the mass flow rate at the outlet decreases with the increase of spool displacement. We expect that PCV valve designers can easily understand fluid flow inside a PCV valve with our visual information for their help.