• Korean Journal of Materials Research
• /
• v.25 no.11
• /
• pp.598-601
• /
• 2015

Using reverse micelle processing, $ZnAl_2O_4$ nanopowders were synthesized from a mixed precursor(consisting of $Zn(NO_3)_2$ and $Al(NO_3)_3$). The $ZnAl_2O_4$ was prepared by mixing the aqueous solution at a molar ratio of Zn : Al = 1 : 2. The average size and distribution of the synthesized powders with heat treatment at $600^{\circ}C$ for 2 h were in the range of 10-20 nm and narrow, respectively. The average size of the synthesized powders increased with increasing water to surfactant molar ratio. The XRD diffraction patterns show that the phase of $ZnAl_2O_4$ was spinel(JCPDS No. 05-0669). The synthesized and calcined powders were characterized using a thermogravimetric - differential scanning calorimeter(TG-DSC), X-ray diffraction analysis (XRD), and high resolution transmission electron microscopy(HRTEM). The effects of the synthesis parameter, such as the molar ratio of water to surfactant, are discussed.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.394-398
• /
• 1998

$Pb_{1-x}Sr_x(Mg-{1}2}W_{1}2})O_3$$ ceramics for application in the microwave frequency range were investigated by dielectric constant and X-ray diffraction measurements. The dielectric constant curves showed two concentration dependent characteristics in the $$Pb(Mg-{1}2}W_{1}2})O_3$-rich$ region. As the Sr constant further increases to x=0.3 the dielectric curve levels off. In the concentration range between x=0.4 and x=1 in which dielectric constant dependence on temperature is negligible, it decreases and Qf value increases in the microwave frequency with increasing Sr. The temperature coefficient (${\tau}_{\varepsilon} $) of the dielectric constant changes from the negative to positive value between x=0.9 and x=1. The dielectric constant, Qf and $\tau\varepsilon$ are correlated with tolerance factor(t). From the X-ray diffraction results for $0.1{\le}x{\le}1$ the cell parameter is found to decrease as x increases and B-site ordering is observed in all the composition ranges.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.12
• /
• pp.4059-4062
• /
• 2012

The effect of a conductive agent on the structural and electrochemical properties of $Li_4Ti_5O_{12}$(LTO) spinel was investigated through neutron diffraction during Li intercalation and electrochemical measurements. The charging process of LTO is known as transformation of the white $(Li_3)_{8a}[LiTi_5]_{16d}O_{12}$ into a dark-colored $(Li_{3-X})_{8a}[Li_{X+Y}]_{16c}[LiTi_5]_{16d}O_{12}$ by incorporating the inserted Li into octahedral 16c sites, and the Li in tetrahedral 8a sites shifted to 16c sites. The occupancy of the tetrahedral 8a site varied with the existence of carbon in the electrode. Without carbon, the lattice parameter and cell volume of LTO decreased more notably than in the carbon-containing LTO electrode during Li insertion process. These phenomena might be attributed that the Li occupancy of the tetrahedral 8a of the LTO electrode without carbon was less than that of the carbon-containing LTO electrode.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.50-56
• /
• 2011

In this study, the effects of ZnO buffer layer thickness and annealing temperature on the heterojunction diode, ZnO/b-ZnO/p-Si(111), were reported. The effects of those on the structural and electrical properties of zinc oxide (ZnO) films on ZnO buffered p-Si (111) substrate were also studied. Structural properties of ZnO thin films were studied by X-ray diffraction and I-V characteristics were measured by a semiconductor parameter analyzer. ZnO thin films with 70 nm thick buffer layer and annealing temperature of $700^{\circ}C$ showed the best c-axis preferred orientation. The best electrical property was found at the condition of buffer layer annealing temperature of $700^{\circ}C$ and 50nm thick ZnO buffer layer (resistivity: $2.58{\times}10^{-4}[{\Omega}-cm]$, carrier concentration: $1.16{\times}1020[cm^{-3}]$). The I-V characteristics for ZnO/b-ZnO/p-Si(111) heterojunction diode were improved with increasing buffer layer thickness at buffer layer annealing temperature of $700^{\circ}C$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.96-103
• /
• 1994

The GaAs epilayer was grown at low temperature (LT. 250.deg. C) by molecular beam epitaxy. The properties of the LTT GaAs, before and after Rapid Thermal Annealing(RTA), were analyzed by Reflection of High Energy Electron Diffraction (RHEED), Double Crystal X-ray(DCX), Raman spectroscopy, PL and Photo-Induced Current Transient Spectroscopy (PICTS). The LT GaAs before RTA, was analyzed by RHEED and DCX, with a result of an improved surface morphology under a relatively As-rich(As/Ga ratio :28) condition, and of an increased lattics parameter of 1.1 1.7% in comparison with a GaAs substrate. However DCX and Raman spectroscopy revealed that the expanded lattics parameter and the crystallinity of LT GaAs could be recovered after RTA. On the other hand, PL spectra indicated that LT GaAs after RTA showed low optical sensitivity unlike High Temperature(HT) GaAs, and that its surface morphology and crystallinity were corresponded with those of HT GaAs. Finally PICTS spectra proved the fact that low sensitivity of LT GaAs was due to the deep level defects (Ec-0.85eV) which were strogly formed by raising RTA temperature to 750.deg. C.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Ocean Systems Engineering
• /
• v.2 no.2
• /
• pp.99-113
• /
• 2012

Steel Catenary Risers (SCR) are the simplest and often the most economic solution compared to other riser types such as flexible pipe, riser towers, top tensioned risers, etc. The top of a SCR is connected to the host platform riser porch. The other end of the SCR connects to flowlines from subsea wells. The riser touchdown point (TDP), which is the location along the riser where contact with the sea floor first occurs, exhibits complex behaviors and often results in compression and fatigue related issues. Heave dynamic responses of semisubmersibles in extreme and operating sea states are crucial for feasibility of SCR application. Recent full field measurement results of a deep draft semisubmersible in Hurricane Gustav displayed the considerable discrepancies in heave responses characteristics between the measured and the simulated results. The adequacy and accuracy of the simulated results from recognized commercial software should be examined. This finding raised the awareness of shortcomings of current commercial software and potential risk in mega investment loss and environmental pollutions due to SCR failures. One main objective of this paper is to attempt to assess the importance and necessity of accounting for viscous effects during design and analysis by employing indicator of viscous parameter. Since viscous effects increase with nearly third power of significant wave height, thus newly increased metocean criteria per API in central Gulf of Mexico (GoM) and even more severe environmental conditions in Western Australia (WA) call for fundamental enhancements of the existing analysis tools to ensure reliable and robust design. Furthermore, another aim of this paper is to address the impacts of metocean criteria and design philosophy on semisubmersible hull sizing in WA and GoM.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.1
• /
• pp.35-40
• /
• 2007

Cobalt ($Co^{2+}$) doped yttria stabilized cubic zirconia (YSZ, $Y_2O_3\;:\;25{\sim}50wt%$) single crystals grown by a skull melting method were heat-treated in $N_2\;at\;1000^{\circ}C$ for 5 hrs. The reddish brown single crystals were changed into either violet or blue color, respectively. Before and after heat treatment, the Co-doped YSZ crystals cut for wafers (${\phi}6.5{\times}t\;2mm$) and round brilliant (${\phi}10mm$). The optical and structural properties were examined by UV-VIS spectrophotometer and XRD. These results are analyzed absorption by $Co^{2+}\;(^4A_2(^4F)\to{^4P})\;and\;Co^{3+}$, change of energy gap and lattice parameter.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.548-554
• /
• 1997

The single crystal of $Mg_{0.16}Zn_{0.84}$Te:Co(Co:0.01 mole%) was grown by vertical Bridgman method. The crystal structure of $Mg_{0.16}Zn$_{0.84}$Te:Co and optical absorption properties of this compound were studied. The grown single crystal has a cubic structure and a lattice constant a=6.1422 $\AA$ were determined by X-ray diffraction. As a result of the optical absorption spectra of $Mg_{0.16}Zn_{0.84}$Te:Co, the intracenter transitions due to $Co^{2+}$ ions were detected for $A-band:^4A_2(^4F){\to}^4T_2(^4F),\; B-band:^4A_2(^4F){\to}^4T_1(^4F), C- band:^4A_2(^4F){\to}^4T_1(^4P)$.The charge transfer transition near the absorption edge was observed in the wavelength range of 550 to 770 nm. According to the crystal field theory, the crystal field parameter(Dq) and the Racah parameter(B) were determined.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.258-269
• /
• 1999

It is important to evaluate fatigue damage of in-service material in respect to assure safety and remaining fatigue life in structure and mechanical components under cyclic load . Fatigue damage is represented by mathematical modelling with crack growth rate da/dN and cycle ration N/Nf and is detected by X-ray diffraction and ultrasonic wave method etc. But this is estimated generally by single parameter but influenced by many test conditions The characteristics of it indicates fatigue damage has complex fracture mechanism. Therefore, in this study we propose that back-propagation neural networks on the basis of ration of X-ray half-value breath B/Bo, fractal dimension Df and fracture mechanical parameters can construct artificial intelligent networks estimating crack growth rate da/dN and cycle ratio N/Nf without regard to stress amplitude Δ $\sigma$.