• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1590-1592
• /
• 1999

We have fabricated good quality superconducting $YBa_2Cu_3O_{7-{\delta}}$ thin films on Hastelloy(Ni-Cr-Mo alloys) with $CeO_2$ buffer layers by in-situ pulsed laser deposition in a multi-target processing chamber. Using one of electrical properties of YBCO superconducting which the resistance approaches to zero dramatically on transition temperature, we have researched to make power transmission line, we have deposited YBCO thin film on flexible metallic substrate. However, it is difficult to make films on flexible metallic substrates due to both interdiffusion problem between metallic substrate and superconducting layer and non-crystallization of YBCO on amorphous substrate. From early research, two ways-using textured metallic substrate and buffer layer-were proposed to overcome theses difficulties. We have chosen $CeO_2$ as a buffer layer which has cubic structure of $5.41{\AA}$ lattice parameter and only 0.2% of lattice mismatch with $3.82{\AA}$ of a-axis lattice parameter of YBCO on (110) direction of $CeO_2$. In order to enhance the crystallization of YBCO films on metallic substrates we deposited $CeO_2$ buffer layers at varying temperature $700^{\circ}C$ to $800^{\circ}C$ and $O_2$ pressure. By X-ray diffraction, we found that each domination of (200) and (111) orientations were strongly relied upon the deposition temperature in $CeO_2$ layer and the change of the domination of orientation affects the crystallization of YBCO upper layer.

• Analytical Science and Technology
• /
• v.12 no.1
• /
• pp.40-46
• /
• 1999

Zn-Ni alloy electrodeposition on steel has been examined by means of X-ray diffraction and scanning electron microscopy. The effect of current density, $Ni^{2+}$ ion concentration, and $Cl^-$ ion concentration on the structure as well as morphology of the electrodeposit have been studied. The Ni content of the electrodeposit increased with decreasing current density in the range studied in this work. The Ni content of the electrodeposit also increased with increasing $Ni^{2+}$ ion and $Cl^-$ ion concentrations. The structure change of the electrodeposit was closely related to the Ni content. In fact, the mixture phase of ${\eta}$ and ${\gamma}$ was found below 10 wt.% of Ni while the ${\gamma}$ phase only was observed above 10 wt.% of Ni. In addition, the lattice parameter, a, of then phase structure increased and the lattice parameter, c, of it decreased as the Ni content of the electrodeposit increased. The morphology of the electrodeposit varied from the plate-like shape to the fine granular shape depending upon the change in composition and structure of the electrodeposit.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.2
• /
• pp.121-129
• /
• 1996

The solubility of Ti in Al matrix was determined by X-ray diffraction method on two different mechanical alloying systems, i.e Al+$Al_3Ti$ and Al+Ti alloys. Starting powder compositions of two systems were chosen for final volume fraction of $Al_3Ti$ phase being 25%. The solubility of Ti in ${\alpha}$-Al was estimated by the lattice parameter measurement of Al. For Al+$Al_3Ti$ mixture, it appeared that some of $Al_3Ti$ particles decomposed during milling and maximum solubility of Ti in Al was about 0.99%. The majority of $Al_3Ti$ particles were dispersed uniformly in Al matrix, having approximate size of 100~200 nm. On the other hand, higher Ti solubility of 1.24 wt.% was found in Al+Ti system, with starting composition of Al+10 wt.%Ti. After 15 hours of milling, Ti phase was identified as 20 nm sized particles embedded in Al matrix. The annealing of mechanically alloyed powders from Al+$Al_3Ti$ and Al+10 wt.%Ti systems was followed in the temperature range of 200 to $600^{\circ}C$ to study thermal stability of supersaturated solution of Al(Ti). After annealing, the lattice parameter of Al reverted back to that of pure Al, and the peak intensity ratio of $Al_3Ti$/Al was increased more than the original value before annealing. These results suggest that Ti dissolve into alpha-Al solutions during milling, and by annealing, $Do_{22}-Al_3Ti$ phase forms from Al(Ti) solution.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.688-694
• /
• 1999

Ti-6Al-4V-N films have been grown onto glass substrates by dc reactive magnetron sputtering from a Ti-6Al-4V-N alloy target at different nitrogen partial pressure, input powers and sputtering times. The influence of various sputtering conditions on structural properties of Ti-6Al-4V-N films was investigated by measuring their X-ray diffraction. The quaternary Ti-6Al-4V-N film is crystallizing in a face centered cubic TiN structure, the lattice parameter is smaller than the TiN parameter as titanium atoms of the TiN lattice are replaced by aluminum and vanadium atoms. The films show the (111) preferred orientation and the (111) peak intensity decreases as the nitrogen partial pressure is increased, but the intensity increases as the sputtering time is increased. The deposition rate and the grain size are alto related with the variation of various sputtering conditions.

• Journal of Surface Science and Engineering
• /
• v.48 no.6
• /
• pp.253-259
• /
• 2015

The test equipment becomes more important with the development of semiconductor industry. MEMS probe is an important testing component to detect the defects from the generated electric signal when it contacts the metal pad of semiconductor devices. Ni-Pd alloy has been paid attention to as a candidate of MEMS probe material because of its high surface hardness and relatively low resistivity. In this study, electroplated Ni-Pd alloy has been prepared by using ethylene diamine as a complexing agent. Solid solution alloy coating could be formed when concentration of palladium chloride and current density were in the ranges of 1~5 mM and $0.2{\sim}1.5A/dm^2$, respectively. The increase of current density brought about an decrease in palladium content, which made both of lattice parameter and grain size smaller. As a result of grain refinement, high hardness could be obtained. However, surface cracking was observed due to residual stress when the current density was above $1.3A/dm^2$. When effects of heat treatment temperature on hardness and sheet resistance were investigated, the accompanied grain growth decreased both of them. The decrease of hardness remained stable at a temperature of $200^{\circ}C$. The sheet resistance was drastically reduced at $100^{\circ}C$. After that, it was found to become constant.

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.28-35
• /
• 1993

In the case of an imaging system affected by aberrations which are not precisely known, the effect of aberrations can be minimized and near-diffraction-limited images can be restored by introducing artificial random phase fluctuations in the exit pupil of the imaging system and using bispectral speckle imaging. In order to determine the optimum value of the correlation length for Gaussian random phase model, computer simulation is performed for 50 image frames of a point object in the presence of defocus, spherical aberration, coma, astigmatism of 1 wave, respectively. In terms of the criterion of performance, the FWHM of the point spread function, normalized peak intensity, MTF and visual inspection of the restored object are employed. The optimum value for the rms difference $\sigma$ of aberration on the exit pupil in the interval of Fried parameter ${\Upsilon}_0$ is given by 0.27-0.53 wave for spherical aberration, and 0.24-0.36 wave for defocus and astigmatism, respectively. It is found that the bispectral speckle imaging technique does not give good results in the case of coma.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.4
• /
• pp.362-370
• /
• 2008

In this paper, we propose a 2D-FE model in single impact with combined physical factors to obtain a unique residual stress by shot peening. Applied physical parameters consist of elastic-plastic deformation of shot ball, material damping coefficients, strain rate, dynamic friction coefficients. As a kinematical parameter, there is impact velocity. Single impact FE model consists of 2D axisymmetric elements. The FE model with combined factors showed converged and unique distributions of surface stress, maximum compressive residual stress and deformation depth. Further, in contrast to the FE models with rigid shot and elastic deformable shot, FE model with plastic deformable shot produces residual stresses very close to experimental solutions by X-ray diffraction. We therefore validated the 2D FE model with combined peening factors and plastic deformable shot. This FE model will be a base of the 3D FE model for residual stresses by multi-impact shot peening.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.146-149
• /
• 2016

The CrN/TiN/Al thin films for solar selective absorber were prepared by dc reactive magnetron sputtering with multi targets. The binary nitride CrN layer deposited with change in N₂ gas flow rates. The gas mixture of Ar and N2 was an important parameter during sputtering deposition because the metal volume fraction (MVF) was controlled by the N2 gas flow rate. In this study, the crystallinity and surface properties of the CrN/TiN/Al thin films were estimated by X-ray diffraction (XRD), atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). The composition and depth profile of thin films were investigated using Auger electron spectroscopy (AES). The absorptance and reflectance with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 300~1,100 nm.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.6
• /
• pp.105-110
• /
• 2008

We have investigated the high temperature rapid thermal annealing of GaN epilayers in nitrogen atmosphere. Annealing has been performed in a rapid thermal annealing furnace at $950^{\circ}C$. The effect of rapid thermal annealing of GaN was studied by x-ray diffraction. The Bragg peak shifts toward larger angle as the annealing time increases. The full width at half maximum (FWHM) of the peak slightly increase, followed by decreases, and increases again as the thermal treatment time increases. The improvement of structural properties of the samples was observed after rapid thermal annealing under optimum conditions. This improvement in crystal quality is due to a reduction of the spread in the lattice parameter in epilayers.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.125-128
• /
• 2001

In this wort, the $Na^+-MMT$ has organically modified with silane intercalant to prepare the polymer/clay nanocomposites. The pH. X-ray diffraction (XRD), and contact angles were used to analyze the surface properties of clay and the exfoliation phenomenon of clay interlayer, The mechanical interfacial properties of epoxy/clay nanocomposites were investigated by three-point bending test. From the experimental results. the surface modification made by silane intercalant on clay surface leads to an increase of distance of silicate layers, surface acid value. and electron acceptor parameter of organoclay. The treatments are also necessary and useful for epoxy to intercalate into the interlayer by interacting of electron donor-accepter between basic epoxy and clay surface. The mechanical interfacial properties of the nanocomposites was improved by the presence of dispersed clay nanolayer containing low content of organoclay in comparison with the conventional, which increase the interfacial adhesion between dispersed clay and epoxy resins.