• Korean Journal of Food Science and Technology
• /
• v.24 no.5
• /
• pp.463-469
• /
• 1992

Effect of thermal processing upon the structure formation of surimi was investigated by differential scanning calorimeter (DSC), rigidity changes during heating, and scanning electron microscopy (SEM). DSC studies showed the transition temperatures and heat capacity of the proteins during heating. Thermal transition peaks of the proteins were shifted to the lower temperatures or disappeared by the addition of salt and higher heating rate or setting treatment ($4^{\circ}C$ or $40^{\circ}C$). Whereas setting at $4^{\circ}C$ for 24hr produced elastic component and showed a permanent effect in rigidity development during heating, setting at $40^{\circ}C$ for 30 min produced a temporary effect. SEM studies in conjunction with rigidity scanning provided an insight into the structural features of the gel and helped clarify the setting and protein modification effects.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.5
• /
• pp.197-202
• /
• 2001

The influence of thermal treatment and cold drawing was investigated for poly(ethy1ene terephthalate) films fabricated with various experimental conditions. Samples were elongated at room temperature under stepwise-drawing condition with the cross-head speed kom 0.5 to 500 mrdmin in an universal tester. Stress oscillation was observed in the stress-stnin curve of the samples heat-treatd at 50, 72 and $129^{\circ}C$ for 30 min, but it was not observed in the samples heat-treatd at $83^{\circ}C$ for 30 min. Thermal analyses of the samples were carried out in differential scanning calorimeter at the heating rate df $10^{\circ}C$/min/min, and the glass transition temperature, crystallization peak, enthalpy of fusion and degree of crystallinity were measured. The dynamic mechanical analyses of the samples were also carried out in a multiplefimction internal kiction pendulum at 1 Hz with the heating rate of $1.5^{\circ}C$/min, and it was found that the elastic modulus increases in the order of non-treated, heat-treated, and elongated samples.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.1
• /
• pp.110-117
• /
• 2000

A series of new liquid crystalline dimesogenic compounds with chiral tails was synthesized, and their thermal and liquid crystalline properties were studied. The chain length of the central polymethylene spacers (x) was varied from dimethylene (2) to decamethylene (12). These compounds were characterized by elemental analysis, IR and NMR spectroscopy, differential scanning calorimetry (DSC), and cross-polarizing microscopy. All compounds were found to be enantiotropically liquid crystalline, and the values of melting ($T_m$) and isotropization temperature ($T_i$) as well as enthalpy change (Δ$H_i$) and entropy change for isotropization (Δ$S_i$) decreased in a zig-zag fashion revealing the so-called odd-even effect as x increases. Their mesomorphic properties fall into three categories depending upon x; (a) compounds with x=2 and 4 formed two different mesophases, smectic and cholesteric phases in that order on heating, and vice versa on cooling, (b) compounds with x=3, 7, 8, 10 and 11 reversibly formed only the cholesteric phase, and (c) compounds with x=5, 6, 9 and 12 exhibited only a cholesteric phase on heating, whereas on cooling they formed two different mesophases, cholesteric and smectic phases, sequentially.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.837-844
• /
• 2000

The cure behavior of commercial epoxy molding compounds (EMC) commonly used for IC package was studied at constant cure temperatures as well as at constant heating rates using differential scanning calorimetry (DSC), rheometer, and dielectric analyzer (DEA). The cure kinetics were obtained using autocatalytic reaction model according to the Ryan Dutta method after assuming m+n equal to 2. The prediction of reaction rates by the model equation corresponded well to experimental data at all temperatures except for 10$0^{\circ}C$. The phase transitions such as gelation and vitrification occurred during network formation. At each isothermal cure temperature, $T_{g}$ was measured in accordance with cure time, and the vitrification point was attained when $T_{g}$ was equal to $T_{cure}$. The temperature dependence of gel points and vitrification points showed good agreement with Arrhenius relation. DEA using parallel plate electrode was effective for the monitoring of EMC cure. we knew that if the resin systems are materials of comparable quality, $_{gel}$$T_{g}$ is constant regardless of accelerator concentration in TTT (Time-Temperature-Transformation) diagram.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.4
• /
• pp.237-245
• /
• 1997

A study was conducted to examine the effects of In addition on the precipitation behaviors of Al-2.1Li-2.9Cu alloy by differential scanning calorimetry, transmission electron microscopy and micro-hardness tester. DSC analysis was measured over the temperature range of $25{\sim}550^{\circ}C$ at a heating rate of $2{\sim}20^{\circ}C$/min. The heat evolution peaks due to the formation of GP zone and ${\delta}$'phase shift to higher temperature and the peaks to $T_1$ and ${\theta}$'phases shift to lower temperature by In addition. From this result, it was proved that the formation of GP zone and ${\delta}$'phase is suppresed whereas that of $T_1$ and ${\theta}$'phases are accelerated by the In addition of 0.15wt%. The age hardening curve aged at $190^{\circ}C$ showed that the In bearing alloy(alloy B) has more faster age hardening response and a higher peak hardness than In-free alloy(alloy A), attributed to the fine and homogeneous distribution of $T_1$ and ${\theta}$'phases. The activation energies for the formation of ${\delta}$'phase in In-free and In-bearing alloys are 22.3kcal/mol and 18.6kcal/mol, respectively. Those for $T_1(+{\theta}^{\prime})$ phase of In-free and In-bearing alloys are 24.3 and 37.5kcal/mol, respectively. Quenched-in excess vacancies play an important role to the formation of precipitates.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.62-68
• /
• 2003

Ba-ferrite particles added with Co and Ti, which were known well the additives for the control in coercivity, were synthesized by sol-gel method. In the range 90 to 120 minute reaction time, a stable sol solution which showed no change with temperature, pH, viscosity and aging time. After dried and heat treatment of sol solution, Ba-ferrite phase formed at $700^{\circ}C$ with Differential Thermal Analysis(DTA) and X-Ray Diffractometer(XRD) measurement. The crystallinity became to be better with increasing the temperature. It were showed by Scanning Electron Microscopy(SEM) that Ba-ferrite increased to particle sizes as increasing heating temperature and obtained of narrow particles size distribution. Also, magnetic characteristics of Ba-ferrite powders Co and Ti added were observed by a Vibrating Sample Magnetometer(VSM). Saturation magnetization$(M_s)$ was not much changed, however. the coercivity$(H_c)$dramatically dropped with addition of Co and Ti.

• Korean Journal of Materials Research
• /
• v.2 no.4
• /
• pp.257-262
• /
• 1992

The cure kinetics of a diglycidyl ether of bisphenol A (DGEBA) with 4, 4'-methylene dianiline (MDA) added succinonitrile was studied through the dynamic run method by applying the data to the Kissinger equation which analyses the effect of the heating rate on the temperature at maximum reaction rate using Differential Scanning Calorimetry (DSC) analyzer in the range of 3$0^{\circ}C$-35$0^{\circ}C$. In the DGEBA/MDA system with SN, the activation energy ($E_a$) and the pre-exponential factor (A) were calculated. From these results, the rate constants (k) were obtained according to the different SN contents.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.4
• /
• pp.252-260
• /
• 1996

A study was conducted to examine the precipitation phenomena of Al-2.1Li-2.9Cu alloy by differential scanning calorimetry and transmission electron microscopy. DSC curves were measured over the temperature range of $25{\sim}550^{\circ}C$ at a heating rate of $2{\sim}20^{\circ}C$/min.. Three heat evolution peaks and three heat absorption peaks were observed in the DSC curve for the as-quenched specimen. From DSC results and TEM analysis, it was proved that the precipitation sequence in the as-quenched specimen is supersaturated solid solution ${\rightarrow}$ GP zone ${\rightarrow}{\delta}^{\prime}{\rightarrow}T_1{\rightarrow}T_2$ and ${\theta}^{\prime}$ was detected in the peak aged specimen at $160^{\circ}C$. The major phase formed at peak hardeness in the aging at $160^{\circ}C$ was ${\delta}^{\prime}$ phase. The activation energies for the formation of ${\delta}^{\prime}$ and $T_1$ phases were 22.3kcal/mole and 24.3kcal/mole, respectively. These lower activation energies than those for diffusion of Cu and Li in Al are ascribed to the quenched-in excess vacancies.

• Macromolecular Research
• /
• v.13 no.2
• /
• pp.156-161
• /
• 2005

The thermal transitions of a nylon 6/layered silicate nanocomposite were studied by differential scanning calorimetry and in-situ synchrotron X-ray diffraction. The drawn film of the nylon 6/layered silicate nanocomposite typically showed three endotherms in the DSC thermogram; a very broad endotherm at $\sim120^{\circ}C(T_{1})$, a double-melting endotherm at $\sim215^{\circ}C(T_{2})$, and a high temperature endotherm at $\sim240^{\circ}C(T_{3})$. The drawn film of the nylon 6/ layered silicate nanocomposite was comprised of a mixture of the $\alpha and \gamma$ forms, with $the \alpha form$ being generated by drawing the pressed film having $the \gamma form$. The melting and crystallization of the crystals were observed at the above thermal transitions during the heating experiment performed at the Pohang X-ray synchrotron radiation source (4C2). The newly generated form was meta-stable and melted $at {\sim}T_{1}$. The double-melting $at {\sim}T_{2}$ was due to the exothermic crystallization of $the \alpha form$ during the main endothermic melting of $the \gamma form$. $The \alpha form$ crystallized $at {\sim}T_{2}$ and melted $at {\sim}T_{3}$.

• Smart Structures and Systems
• /
• v.24 no.3
• /
• pp.361-377
• /
• 2019

The stiffness of shape memory alloy (SMA) spring while in actuation is represented by an empirical model that is derived from the logistic differential equation. This model correlates the stiffness to the alloy temperature and the functionality of SMA spring as active variable stiffness actuator (VSA) is analyzed based on factors that are the input conditions (activation current, duty cycle and excitation frequency) and operating conditions (pre-stress and mechanical connection). The model parameters are estimated by adopting the nonlinear least square method, henceforth, the model is validated experimentally. The average correlation factor of 0.95 between the model response and experimental results validates the proposed model. In furtherance, the justification is augmented from the comparison with existing stiffness models (logistic curve model and polynomial model). The important distinction from several observations regarding the comparison of the model prediction with the experimental states that it is more superior, flexible and adaptable than the existing. The nature of stiffness variation in the SMA spring is assessed also from the Dynamic Mechanical Thermal Analysis (DMTA), which as well proves the proposal. This model advances the ability to use SMA integrated mechanism for enhanced variable stiffness actuation. The investigation proves that the stiffness of SMA spring may be altered under controlled conditions.