• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.219-220
• /
• 2006

To understand the effect of powder characteristics on the thermal debinding behavior, PIM parts produced with powders with different particle sizes and particle shapes were examined to determine their weight losses during thermal debinding. The results show that the average diameter of the pore channel in the compact increased when the temperature increased and when coarse powders were used. However, the weight loss rates did not increase proportionally with the pore size. This suggests that the different powders that are frequently used in PIM parts do not affect the thermal debinding rate significantly. This is because the pore size is much larger than the mean free path of the decomposed gas molecules. Thus, the diffusion rates of the gases are not rate-controlling in thermal debinding. The controlling mechanism of the thermal debinding rate is the decomposition of the backbone binder in the PIM parts.

• Journal of Korean Society of Transportation
• /
• v.22 no.3 s.74
• /
• pp.95-105
• /
• 2004

The fundamental diagram is a important element in a variety of transportation studies. While various shapes of the fundamental diagram have been proposed and numerous debates on the best-fit fundamental diagram have been made, the reason why the fundamental diagram has many different shapes has not been well explained. This study introduces time sap as a key parameter to understand drivers' behavioral differences at different locations and traffic conditions, then relate to the shape of the fundamental diagram. From the freeway event detector data, it is shown that time gap follows a certain probabilistic distribution and its mean value varies along locations. It also turns out that drivers take different time gaps for different travel speeds. Three different types of time gap-speed diagrams are identified and matched to Greenberg, reversed-lambda, and inverted-V types of fundamental diagrams, respectively. This study explains the characteristics of fundamental diagrams using time gap as a microscopic variable and describes drivers' behavioral characteristics according to traffic and geometric conditions.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.5
• /
• pp.1215-1217
• /
• 2009

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.3
• /
• pp.23-29
• /
• 2010

A supersonic nozzle specially is one of the important part in a supersonic turbine usually adapted the impulse type, because the flow acceleration in the turbine theoretically is done only in the nozzle. The present study deals with numerical flow analysis to investigate the effect of nozzle shapes on the performance characteristics of a partial admission supersonic turbine. The flow analysis was performed for four different nozzle shapes. The shapes of the nozzles are circular, square, straight rectangular and bent rectangular nozzles. The results of the flow analysis showed that the aerodynamic loss of turbine is highly affected by the nozzle shapes, and the partial admission loss is also highly depended on nozzle shapes. Specially, bent rectangular nozzle had the best performance among the nozzle shapes

• Transactions of Materials Processing
• /
• v.18 no.7
• /
• pp.565-571
• /
• 2009

This paper is concerned with the analysis on the surface stress profiles of perfectly plastic material in backward extrusion process. Due to heavy surface expansion appeared usually in the backward extrusion process, the tribological conditions along the interface between the material and the punch land are very severe. In the present study, the analyses have focused to reveal the surface conditions at the contact boundary for various punch shapes in terms of surface expansion, contact pressure, and relative movement between punch and workpiece which consists of sliding velocity and distance, respectively. Punch geometries adopted in the analysis include concave, hemispherical, pointed and ICFG recommended shapes. Extensive simulation has been conducted by applying the rigid-plastic finite element method to the backward extrusion process under different punch geometries. The simulation results are summarized in terms of surface expansion, contact pressure, sliding velocity and sliding distance at different reduction in height, deformation patterns, and load-stroke relationship, respectively.

• Journal of the Korean Society of Costume
• /
• v.56 no.2 s.101
• /
• pp.101-111
• /
• 2006

The purpose of this research is to define body shapes of Plus-sized women at ages between 21 and 69 whose satisfied the Plus-sized judgment criteria took part in this study. This research also classifies different body types, and provides basic data for designing prototypes according to each body type. Based on factor analysis of the measured data, nine key factors are grouped. And four different body types are classified based on the cluster analysis using factor marks. Type 1 refers to those who are tall and characterized by 'Y' body shape when looked from the front. Looking from the side, this type is comparatively balanced obese type which has flat breast and abdomen, and which has a jutting back and buttocks. Type 2 refers to those who are the shortest of all the obese with 'X' front. This type is Sway-back shape which has jutting back and abdomen but flat buttocks when looked from the side. Type 3 is characterized by 'H' body shape when looked from the front. This type is Pway-back shape which has flat back, abdomen and buttocks when looked from the side. The prominent breast part of this type is the most outstanding figure. Type 4 is characterized by 'X' when looked from the front. This type has a jutting waist and prominent buttocks when looked from the side.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.3
• /
• pp.296-303
• /
• 2016

In this paper, a numerical experiment on a tidal turbine was performed based on a water wheel design using the commercial CFD code ANSYS-CFX to contribute to the development of water wheels. The water wheel type tidal turbine was studied with different numbers of rotor blades (including ten, twelve and twenty blades types) and with different blade shapes (Straight, Curved and Zuppinger types) for comparison at several values of tip speed ratio (TSR) ranging from 0.7 to 1.2. The numerical results indicated that the 10-bladed type and the Straight-bladed type turbines absorb the highest power efficiency, up to 43 % at TSR 0.9. In addition, the 20-bladed and the Curved-bladed types showed the lowest performances in all cases of TSRs comparing with the others. Besides that, it was found that this turbine operates much effectively at low range of TSR, especially at TSRs 0.9 and 1 for all cases of blade shapes and all numbers of blades.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.203-208
• /
• 2008

The purpose of this study is to compare the different shapes of condenser of the direct contact heat transfer from the heat pipe condenser to the receiving water using CFD. The heat transfer from the working fluid of the heat pipe to receiving fluid flows through the manifolder is one of the important part in evacuated solar collector system. The retrenchment of the thermal resistance between the heat pipe and the manifolder could increase the thermal performances of the whole system. Recently, direct heat transfer from the heat pipe condenser wall to the receiving water was suggested and accompanied experiments were achieved. This experiment shows the better performances of the direct contact heat transfer analogically. Preceding calculations are carried out for the performance comparison: mesh dependence test, discretization method test and equation model test. with these preceding tests, 4 different shapes of condenser are compared and each case were set up for the same heat flux at the condenser wall. The calculation result shows that the efficiency of the extended surface condenser shape is 10% higher then the that of the others.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.311-315
• /
• 2006

Various core shapes of cylindrical drains are used for accelerating primary consolidation for soft clay deposits, but serious harmful disadvantages on drainage capacity may occur on cylindrical drains due to confining Pressure when they are installed in that soil. In this study, two different core shapes of cylindrical drain are used to evaluate the drainage capacity with consideration of clogging effects on their filter jackets for an applied confining pressure. Column tests with radial drainage system were conducted under confining pressure of 50 kPa for 13 days. Two parameters which are discharge and accumulated volume of water drained were measured as the time elapsing. From this experimental study, the results showed that at the Initial stage before the clogging developed enough, the cylindrical drain with angular-type-plastic-core could produce discharge twice higher (maximum) than those with round-type. After 13 days had passed on, cylindrical drain with angular-type-plastic-core could produce discharge only 20% higher than those with round-type one. Eventually, there is a possibility that the efficiency of using angular-type-cylindrical-drain will be similar to the round-type one as the clogging develops more.

• The Korean Journal of Community Living Science
• /
• v.22 no.1
• /
• pp.95-102
• /
• 2011

The purpose of this study was to examine the development of detailed description for drawing houses according to the shapes of lines, and dimensions of space from 4 to 5 years-old children. Participants were 76 children from a daycare center in Busan, Korea. Each child was asked to draw 4 different houses according to the shapes of lines and dimensions of space, such as: straight lines and 2-dimensional pictures straight lines and 3-dimensional Models, curved lines and 2-dimensional pictures and curved lines and 3-dimensional models. The children's drawings were scored based on a "detailed description rating table" which consisted of 10 items. Summarizing the overall results, first, 5 year-olds scored significantly higher than 4 year-olds in the detailed description of 4 different house models. Second, the houses with straight lines scored significantly higher than those with curved lines in the detailed description. Third, there were no significant differences between 2-dimensional houses and those of 3-dimensional models in the detailed description. These results suggest that the detailed description of young children's drawing is developed as children grow older, and drawing with straight lines are earlier developed than curved lined drawings.