• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.371-377
• /
• 2008

In order to obtain fundamental knowledge of atomization, the three dimensional unsteady phenomenon of pinch off was numerically studied by developed method. Not only liquid shapes but also velocity distributions of numerical results were compared with corresponding experimental ones. They showed satisfactorily good agreement at least in a qualitative sense. The liquid jet shapes, the pressure and velocity distributions, and the inner flow structures were clarified through the comparisons of distinctly different flow fields due to presence or absence of surface tension. The condition of pinch off, which had close correlation with fluid acceleration at injection, was clearly specified.

• Korean Journal of Hazardous Materials
• /
• v.6 no.2
• /
• pp.62-67
• /
• 2018

It is very important to classify explosion hazardous area in order to prevent an accident explosion. In order to prevent such a explosion, the Industrial Safety and Health Standards Rules stipulates the establishment and management of explosion hazards in accordance with the criteria set by the Korean Industrial Standards. This study has investigated the range of the explosion hazardous area according to various hole sizes, pressures, vapor densities, and wind velocities in the outdoor flammable liquid tank using KS C IEC-60079-10-1 $2^{nd}$ Ed.(=IEC CODE) and PHAST. The results show that the explosion hazardous areas by IEC CODE have circle shapes. However, the areas by PHAST show ellipse shapes. The different of the explosion hazardous areas increases with the increase of wind velocity.

• Structural Engineering and Mechanics
• /
• v.78 no.3
• /
• pp.369-378
• /
• 2021

This paper reviewed a few output-only system identification algorithms and identified the shortcomings of those popular blind source separation methods. To address the issues such as less sensors than the targeted modal modes (under-determinate problem), repeated natural frequencies as well as systems with complex mode shapes, this paper proposed a complex wavelet modified second order blind identification method (CWMSOBI) by transforming the time domain problem into time-frequency domain. The wavelet coefficients with different dominant frequencies can be used to address the under-determinate problem, while complex mode shapes are addressed by introducing the complex wavelet transformation. Numerical simulations with both high and low signal-to-noise ratios validate that CWMSOBI can overcome the above-mentioned issues while obtaining more accurate identified results than other blind identification methods.

• Structural Engineering and Mechanics
• /
• v.70 no.6
• /
• pp.711-722
• /
• 2019

Considering stress singularities at point support locations, buckling solutions for plates with arbitrary number of point supports are hard to obtain. Thus, new Hp-Cloud shape functions with Kronecker delta property (HPCK) were developed in the present paper to examine elastic buckling of point-supported thin plates in various shapes. Having the Kronecker delta property, this specific Hp-Cloud shape functions were constructed through selecting particular quantities for influence radii of nodal points as well as proposing appropriate enrichment functions. Since the given quantities for influence radii of nodal points could bring about poor quality of interpolation for plates with sharp corners, the radii were increased and the method of Lagrange multiplier was used for the purpose of applying boundary conditions. To demonstrate the capability of the new Hp-Cloud shape functions in the domain of analyzing plates in different geometry shapes, various test cases were correspondingly investigated and the obtained findings were compared with those available in the related literature. Such results concerning these new Hp-Cloud shape functions revealed a significant consistency with those reported by other researchers.

• Elastomers and Composites
• /
• v.56 no.2
• /
• pp.85-91
• /
• 2021

In this study, different types and shapes of various particles produced on the asphalt pavement road were analyzed. Road dust at a bus stop was collected and was separated as per their sizes by using a sieve shaker. Tire-road wear particles (TRWPs), asphalt pavement wear particles (APWPs), mineral particles, plant-related particles, glass beads, glass particles, road paint wear particles, plastic particles, and fibers were observed herein. The types and shapes of the particles varied depending on their sizes. TRWPs larger than 500 ㎛ were not observed. TRWPs with a size of 212-500 ㎛ were rarely present, but many TRWPs with a size smaller than 212 ㎛ were observed. APWPs were observed for whole-particle sizes of below 1,000 ㎛. A variety of particles on the road would lead to lower friction between the tires and the road, thereby increasing the braking distance of vehicles. Most of the particles include mineral particles, glass particles, and APWPs with rough surfaces. Therefore, the abrasion of the tire tread would accelerate owing to friction with the tough particles.

• Elastomers and Composites
• /
• v.58 no.2
• /
• pp.87-94
• /
• 2023

Abrasion tests of an SBR compound were conducted using four different types of abrasion testers (cut and chip, Lambourn, DIN, and LAT100). The abrasion test results were analyzed in terms of size distributions and morphologies of the wear particles. Most wear particles were larger than 1000 ㎛. The wear particle size distributions tended to decrease as the particle size decreased. Except for the Lambourn abrasion test, the wear particles smaller than 212 ㎛ were rarely generated by the other three abrasion tests, implying that small wear particles were produced through friction by introducing talc powder. Shapes of the wear particles varied depending on the abrasion testers. The wear particles generated from the Lambourn abrasion tester had stick-like shapes. The cut and chip abrasion test showed a clear abrasion pattern, but the DIN abrasion test did not show any specific abrasion pattern. The Lambourn and LAT100 abrasion tests showed irregular abrasion patterns.

• Journal of Surface Science and Engineering
• /
• v.56 no.3
• /
• pp.185-191
• /
• 2023

The lifetime and corrosion resistance of the coating depends on its thickness and composition. We checked how the plating progressed according to the shape of the product to be plated. There was no significant difference in the composition or thickness of the plating according to the shape of the separately plated products. Samples of different shapes collected from products with complex shapes showed no significant difference in composition depending on the shape, but significant differences in thickness. This difference is due to the difference in applied current density depending on the shape of the product.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.8-9
• /
• 2021

FCP requires different curvatures and shapes according to the method of division, and it is necessary to manufacture a formwork accordingly. FCP production equipment consists of CNC equipment and side shape control equipment. This can be implemented in various shapes of upper, lower, and side surfaces. In the side shape control equipment, it is implemented as a variable side formwork. Among the required performance of the variable side formwork, there is stiffness against side pressure, which needs to be verified. Therefore, in this study, the FCP fabrication experiment is conducted with the developed variable side formwork. By analyzing the error in the shape of the fabricated FCP, the lateral pressure resistance capability of the side form is measured and verified.

• The International Journal of Costume Culture
• /
• v.13 no.2
• /
• pp.118-129
• /
• 2010

Digital technology introduced into the clothing and fashion industry is evolving to digital virtual fashions and consumer-centered mass-customized production systems. Today the application of such 3D virtual try-on systems is being expanded gradually in the clothing industry. This study purposed to make virtual avatars and virtual garments using OptiTex and V-stitcher virtual software and compared the appearance of the virtual garments put on the virtual avatars. For this, we created virtual avatars and virtual garments using body measurements obtained from jive subjects of top jive body shapes, respectively, using $[TC]^2$ body scanner. According to the results of comparing the outcomes of the two different virtual software systems, virtual avatar II of V-Stitcher tended to have a more round and lifted hip and the waist line at a higher position. In addition, the body curves and shapes of a virtual avatar affect the appearance of virtual garments. This study applied the same body measurements to virtual avatars and the same pattern to virtual garments, but when different kinds of virtual software were used, the virtual avatars and virtual garments showed different appearance and fit. This result may mean that when customers buy apparel products using different kinds of virtual try-on systems, their evaluation of appearance can vary depending on the virtual try-on system. Therefore, research needs to be made actively for the development and use of linkage programs that can reflect actual body measurements between virtual software systems and 3D body scanning systems.

• The Research Journal of the Costume Culture
• /
• v.19 no.1
• /
• pp.31-41
• /
• 2011

Jacket is popular ready-made garment among college students in their early 20s. However, ready-made jackets, which are designed to fit normal people, are not likely to fit sportsmen well who have highly developed muscles in particular parts of their bodies. And muscle development is quite different among sportsmen according to the types of sports and bodily movements. Therefore, ready-made jackets can not be expected to fit sportsmen well as they fit normal people who have different shapes of bodies from sportsmen. The purpose of this study is to investigate the factors of fitness and comfortableness of jackets for sportsmen in their early 20s according to the types of sports to provide basic data for designing suitable garments for them. Research method, 362 college sportsmen in their early 20s were surveyed from June 2nd 2009 to June 9th 2009, and 360 of them were processed statistically, with 2 of them having been discarded for lack of sincerity. Among Taekwondo players, Arm Length was the most complained part, among wrestlers, Biacromion Length was the most complained part, among fencers, 'Waist Circumference' was the most complained part, among swimmers, Biacromion Length was the most complained part, among apparatus gymnast, 'Hip Circumference' was the most complained part, among track athletes and handball players, more than 20% answered that the jackets did not fit them in every parts. It was understood that different sportsmen complained of particular parts of the jackets and that parts of the jacket should be adjusted according to bodily shapes of different sportsmen. This study was made to investigate the factors to be considered in producing ready-made jackets for college sportsmen. It is hoped that more patterns will be developed on the basis of the original form of jacket and the result of this study.