• Korean journal of applied entomology
• /
• v.61 no.1
• /
• pp.239-248
• /
• 2022

Forensic entomology is a study that purposes at field reconstruction through insects attracted to carcasses, and has been mainly studied using carcasses such as a pig and chicken. Therefore, this study was conducted to find out if there is a singularity by using the carcass of water deer with different conditions and shapes of the hair quality and to find out the appearance of a necrophagous insect. The water deer carcass was received from the Jeollanam-do Wildlife Rescue Management Center and research was conducted. From May 19 2021 to July 2 2021, the decay progress of the carcass was observed for about 6 weeks. A total of 51 species of 21 families in 4 orders of insects were collected. Even after the carcass completely decays, even at the stage where the activity of other insects is not observed, insects such as Dermestidae and Tenebrionidae are collected from the hairs and leather of water deer carcass until the last. It was confirmed that insects of the order Coleoptera other than Diptera can be used as forensic entomological data related to the decay of carcasses with fur.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.171-182
• /
• 2022

The safe use of a structure requires it to be maintained in an undamaged state. Thus, a typical factor that determines the safety of a structure is a crack in it. In addition, cracks are caused by various reasons, damage the structure in various ways, and exist in different shapes. Making matters worse, if these cracks are unattended, the risk of structural failure increases and proceeds to a catastrophe. Hence, recently, methods of checking structural damage using deep learning and computer vision technology have been introduced. These methods usually have the premise that there should be a large amount of training image data. However, the amount of training image data is always insufficient. Particularly, this insufficiency negatively affects the performance of deep learning crack detection algorithms. Hence, in this study, a method of augmenting crack image data based on the image translation technique was developed. In particular, this method obtained the crack image data for training a deep learning neural network model by transforming a specific case of a asphalt crack image into a concrete crack image or vice versa . Eventually, this method expected that a robust crack detection algorithm could be developed by increasing the diversity of its training data.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.3
• /
• pp.105-110
• /
• 2022

In line with the trend of the 4th Industrial Revolution, we tried to study the scalability of the craft sector in the art field in the wake of the convergence of new fields through the combination of different fields. To this end, a craft case using 3D printing technology was analyzed based on the theoretical background of the definition and value of digital craft. As a result of the study, craft works using 3D printing technology could be divided into four forms according to the fusion expression method. First, the mixed type was most characterized by harmonious production without significantly deviating from the traditional craft type. Second, the component type was produced in the form in which the characteristics of digital technology, which has advantages of certain shapes and detailed work, were best exhibited. Third, the structural type became a work with analog sensibility by adding traditional craft techniques based on the results output from a 3D printer. Finally, the connection type was the work that showed the greatest glimpse of originality and uniqueness among the analysis cases of this study. As digital technology is positively widely used, future studies will also deal with effective work directions.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.9
• /
• pp.15-24
• /
• 2023

The behavior of buried pipes is directly influenced by the nonlinearity and complex characteristics of the surrounding soil. However, the simplified beam-spring model, which ignores the nonlinearity and complex behavior of soil, is commonly used in practice. In response, several studies have employed continuum analysis methods to account for the nonlinear and complex behavior of the soil. This paper presents various numerical continuum analysis techniques and verifies their comparison with full-scale tests. The study found that reaction force results close to the full-scale test could be obtained by applying contact surface characteristics that take into account the interaction between the ground and the buried pipe. In the case of sharing pipe and soil node method and ignoring the interaction between pipe and soil, excessive reaction force was derived, and the failure shapes were different. In addition, this study applied the dynamic explicit analysis method, ALE method, and CEL method. It was confirmed that the displacement-reaction relationship and failure shape are similar to those of the static analysis.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.111-118
• /
• 2023

The purpose of this study is to study jewelry designs presented to general consumers who seek new products and diversity. We would like to present a modular jewelry design with a structure and combination method that is distinct from jewelry in a multimodal replacement method that allows various product modules sold in the past to be worn interchangeably. Problems are likely to occur when a number of existing rather small parts are manufactured in a complex combination method, and difficulties may follow when consumers replace decorative parts and lose them in the process of assembling small fixture parts. Therefore, in order to reduce these problems, we try to make it different from jewelry products made with a simple and simple design so that it can be easily replaced and worn without the need for other coupling parts, and produced using the latest 3D printer (Rapid Prototyping). In this study, based on the experience and know-how gained while engaging in field work, it was possible to make a real object and focused on minimizing problems during the production process, and through this, time and economic loss can be reduced. The purpose of the study is to produce improved jewelry products by expressing more sophisticated and differentiated shapes by using 3D programs (CAD).

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.243-249
• /
• 2023

The occurrence of cavitation on the propeller is directly linked to the naval ship's survivability, and it is necessary to design a propeller shape that delays the cavitation inception. However, the propeller cavitation can occur under various operating conditions, thus it is important to identify whether the propeller cavitation exists during operation as well as in the design phase. To this end, it is necessary to use noise or vibration signals on board to monitor the cavitation inception. In this study, a hydrophone and an accelerometer were installed on the ship hull right above the propeller to compare the performance of analyzing cavitation inception between acoustic and vibration signals. Also, a high speed camera was used to visually observe the occurrence of cavitation through an observation window. The measured results showed that the spectral shapes between acoustic and vibration signals were different, but the level increases at each frequency band and the overall level of the frequency band from 1 kHz to 10 kHz showed a similar tendency. The Detection of Envelope Modulation On Noise (DEMON) analysis also showed similar results for both acoustic and vibration signals, confirming that both hydrophones and accelerometers can be utilized in the analysis of cavitation inception.

• Advanced Industrial SCIence
• /
• v.2 no.2
• /
• pp.9-15
• /
• 2023

Since silicone rubber heaters are flexible, they can be directly attached or installed in objects to be heated even in flat, curved or three-dimensional shapes. Since the current heating method heats the entire object to be heated and raises it to a required temperature, ignoring areas or positions where heat is not required, partial intensive heating cannot be performed. When using multi-heating zones, rather than heating the entire object to be heated, only the parts that need heat are intensively heated according to the process, so it is possible to heat quickly by local location by applying different amounts of heat with a small amount of electric capacity to each place that needs heat, and heat energy can reduce. In this study, the temperature and heating time of the partially concentrated region in the multi-heating region structure are measured so that a uniform temperature or temperature difference occurs in the region requiring thermal fusion. In order to determine the optimal power density range and reduce capacitance, the safety of a silicon rubber heater manufactured with a multi-heating zone structure is investigated. If the silicon rubber heater is manufactured in a multi-heating method, the multi-intensive heating technology can be ideally applied to all heating processes.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.2
• /
• pp.127-139
• /
• 2023

In this study, minoxidil, which is well known as a pharmaceutical raw material, and diaminopyrimidine oxide (DAO), which is a cosmetic raw material, were used as active ingredients to evaluate the physical properties of niosomes and compare the skin penetrations of artificial skin. To prepare niosomes of the size of nanoparticles, a high pressure homogenization method was used, and physical properties were evaluated with a zetasizer. The particle size of the noisome including the active ingredient was measured to be 99 to 123 nm according to HLB, and the zeta potential was measured in the range of -60 to -81 mV. Through DSC (differential scanning colorimetry), it was confirmed that minoxidil, a crystalline component, was uniformly dissolved in an amorphous state in niosomes. In order to confirm and compare skin penetration, it was measured by the in vitro Franz diffusion cell method, and the niosome formulation showed 3.4 times higher penetration for minoxidil and 11.1 times higher penetration for DAO than the control gel formulation. In addition, when comparing the skin penetration of minoxidil niosome and DAO niosome, a similar trend was shown, and the penetration amount of DAO was relatively high. The shapes of the niosome formulations with different HLB values were observed using Cryo-TEM, and it was confirmed that vesicles were formed in all of them and that they were intermediate between SUV (small unilamella vesicle) and LUV (large unilamella vesicle). Through this study, minoxidil, an effective drug for hair loss, and DAO, a cosmetic raw material, can be effectively delivered to the skin by encapsulating them in a noisome formulation.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.4
• /
• pp.259-271
• /
• 2023

Since the short-wave infrared spectrum has a significant range of variation depending on the production environment, countries with advanced resource exploration are collecting the spectrum and building a database. Representative organizations include the USGS and CSIRO, and they are currently carrying out a project in China that can synthesize and use a large number of existing data. The USGS library provides a total of 2,457 spectra targeting not only minerals but also various materials that respond to infrared radiation. Among these, there are 1,276 mineral spectra, which are about half of the total. The spectrum title includes information, such as analysis devices (NIC4, BECK, ASDNG, etc.), purity codes (a, b, c, d, u), and measurement methods (AREF, RREF, RTGC, TRAN). Analyzed raw data are provided in ASCII and GIF format. The CSIRO library has a total of 502 spectra, of which the majority, 493, correspond to mineral spectra. The USGS library is a free, publically available resource, while the CSIRO library is bundled with TSG8 or must be purchased separately. Among these, when comparing the eight spectra whose spectral shapes can be analyzed with the spectra of domestic illite, the positions of the absorption peaks are significantly different from those of domestic illite, except for one Japanese illite. Additional research will be needed to determine the causes of such differences, and the domestically relevant databases should be established as well.

• Computers and Concrete
• /
• v.33 no.5
• /
• pp.605-619
• /
• 2024

The increase of reclaimed asphalt pavement (RAP) content in recycled asphalt concrete (RAC) is accompanied by the degradation of low-temperature cracking resistance, which has become an obstacle to the development of RAC. This paper aims to reveal the meso-scale mechanisms of the low-temperature fracture behavior of RAC and provide a theoretical basis for the economical recycling of RAP. For this purpose, micromechanical heterogeneous peridynamic model of RAC was established and validated by comparing three-point bending (TPB) test results against corresponding numerical simulation results of RAC with 50% RAP content. Furthermore, the models with different aggregate shapes (i.e., average aggregates circularity (${\bar{C_r}}=1.00$, 0.75, and 0.50) and RAP content (i.e., 0%, 15%, 30%, 50%, 75%, and 100%) were constructed to investigate the effect of aggregate shape and RAP content on the low-temperature cracking resistance. The results show that peridynamic models can accurately simulate the low-temperature fracture behavior of RAC, with only 2.9% and 13.9% differences from the TPB test in flexural strength and failure strain, respectively. On the meso-scale, the damage in the RAC is mainly controlled by horizontal tensile stress and the stress concentration appears in the interface transition zone (ITZ). Aggregate shape has a significant effect on the low-temperature fracture resistance, i.e., higher aggregate circularity leads to better low-temperature performance. The large number of microcracks generated during the damage evolution process for the peridynamic model with circular aggregates contributes to slowing down the fracture, whereas the severe stress concentration at the corners leads to the fracture of the aggregates with low circularity under lower stress levels. The effect of RAP content below 30% or above 50% is not significant, but a substantial reduction (16.9% in flexural strength and 16.4% in failure strain) is observed between the RAP content of 30% and 50%. This reduction is mainly attributed to the fact that the damage in the ITZ region transfers significantly to the aggregates, especially the RAP aggregates, when the RAP content ranges from 30% to 50%.