• Journal of Pharmaceutical Investigation
• /
• v.35 no.4
• /
• pp.279-285
• /
• 2005

Ground CS-891 (N-[1-(4-methoxyphenyl)-1-methylethyl]-3-oxo-4-aza-5a-androst-1-ene-$17{\beta}$-carboxamide) of poorly water soluble drug was obtained using a Heiko Seisakusho model TI-100 vibration mill, and samples with different crystallinity were prepared at mixture ratios of 10:0, 7:3, 5:5, 3:7 and 0:10 (intact;ground CS-891). Physicochemical characterizations were obtained using qualitative and quantitative X-ray diffractometry, different scanning calorimetry (DSC), scanning electron microscopy (SEM), Quantasorb surface area analyzer, and controlled atmosphere microbalance. With increase of amorphous CS-891 in mixture ratios, the intensities of X-ray diffraction peaks of crystalline CS-891 were decreased, whereas surface area, water absorption, and exothermic peaks in DSC were increased. The apparent solubility of ground CS-891 was $4.4\;{\mu}g/ml$ and the solubility of intact CS-891 was $3.1\;{\mu}g/ml$ at $37{\pm}1^{\circ}C$. The apparent precipitation rates of CS-891 in a supersaturated solution during the solubility test were increased with an increase of amorphous CS-891, and a crystalline form of CS-891 transformed from amorphous CS-891 after the solubility test was found by X-ray diffraction analysis, DSC and SEM. The dissolution profiles of CS-891 with different crystallinity at $37{\pm}1^{\circ}C$ by the USP paddle method were investigated, and the apparent dissolution rate constant of ground CS-891 was about 5.9-fold higher than that of intact CS-891. A linear relationships between the crystallinity of CS-891 and the apparent dissolution rate constant (r>0.96) were obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.8
• /
• pp.906-912
• /
• 2012

This paper presents the new method for a six-degree-of-freedom (DOF) motion measurement and those dynamic characterizations in an ultraprecision linear stage using angle sensor-implemented grating interferometry. It consists of a diffractive optical element, a corner cube, four separate two-dimensional position sensitive detectors, four photodiodes and auxiliary optics components. From the previous study, it was confirmed that the proposed optical system could measure a six-DOF motion error in a linear stage. In this article, six-DOF motion dynamic characteristics of the stage were investigated through the step response and with respect to the conditions with a different speed of a slide table. As a result, the natural frequency and damping ratio according to a six-DOF direction was obtained. Also, it was seen that the speed of slide table had an significant effect on a six-DOF displacement motion, especially, X, which was considered as the effect of friction mechanism and local elastic mechanical deformation in a slide guide.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.18.2-18.2
• /
• 2009

Ceramics have some properties that are unmatched by other kind of materials like metals or polymers. The ability of high thermal and chemical resistance and in case of being superior in specific mechanical properties makes the ceramic materials suitable for arange of applications. The microstructure and morphology of a material arguably permit the use of many advanced application otherwise difficult to achieve.Porous structures have some important applications in biomedical and environmental field. For human hard tissue reconstruction and augmentation procedure suitable biomaterials are used with a desirable porosity. A range of porous bioceramics were fabricated with tailored design to meet the demand of specific applications. Channeled and interconnected porosity was introduced in alumina, zirconia, and hydroxyapatite or tri calcium phosphate ceramics by different methods like multi-pass extrusion process, bubble formation in viscous slurry,slurry dripping in immiscible liquid, sponge replica method etc. The detailed microstructural and morphological investigations were carried out to establish the unique features of each method and the developed systems. For environmental filters the porous structures were also very important. We investigated a range of channeled and randomly porous silicon based ceramic composites to enhance the material stability and filtration efficiency by taking advantage of the material chemistry of the element. Detailed microstructural and mechanical characterizations were carried out for the fabricated porous filtration systems.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.10a
• /
• pp.58-58
• /
• 1993

Pervaporation has become important as a method to separate liquid mixtures, sepecially azeotropic and close boiling-point mixtures. Especially, water-alcohol separations have been carried out a lot because of the practical interests in the industries. However, outstanding membranes with high selectivity and high permeability have not been available in common use yet. In order to separate selectively out the water mixed with alcohols with an aim of the purification of the alcohols, a membrane has tO have excellent affinity to water. Among the hydrophilic polymers, polyacrylic acid and poly(vinyl alcohol) are used widely. In recent years, ionomers and polyion complexes, better hydrophitic materials, start to be used. The polyion complex membranes, consisting of polyacrylic acid (PAA) and polycation, showed excellent permeation rates and selectivities. It was known that among the polycations, ioneries, which have quaternary ammonium groups in the backbone chain, were more effective in giving membranes of higher permselectivities. On this base, syntheses and characterizations of the polycations, with different chemical structures from the published ones, for the polyion complex membrane formation were studied in this paper.

• Korean Journal of Materials Research
• /
• v.26 no.12
• /
• pp.741-750
• /
• 2016

Nanofibers(NFs), because of their high surface area and nanosized grains, have appropriate morphologies for use in chemiresistive-type sensors for gas detection applications. In this study, a highly sensitive and selective CO gas sensing material based on Au-decorated $SnO_2$ NFs was fabricated by electrospinning. $SnO_2$ NFs were synthesized by electrospinning and subsequently decorated with various amounts of Au nanoparticles(NPs) by sputtering; this was followed by thermal annealing. Different characterizations showed the successful formation of Au-decorated $SnO_2$ NFs. Gas sensing tests were performed on the fabricated sensors, which showed bell-shaped sensing behavior with respect to the amount of Au decoration. The best CO sensing performance, with a response of ~20 for 10 ppm CO, was obtained at an optimized amount of Au (2.6 at.%). The interplay between Au and $SnO_2$ in terms of the electronic and chemical sensitization by Au NPs is responsible for the great improvement in the CO sensing capability of pure $SnO_2$ NFs, suggesting that Au-decorated $SnO_2$ NFs can be a promising material for fabricating highly sensitive and selective chemiresistive-type CO gas sensors.

• Journal of the Korean Magnetic Resonance Society
• /
• v.18 no.2
• /
• pp.74-81
• /
• 2014

The $N_2O_2$ tetradentate Schiff base ligand, N,N'-bis(salicylidene)pentane-1,3-diamine (Salpn), coupled with 1:2 concentration ratio of 1,3-diaminopentane and salicylaldehyde was used to produce a series of macrocyclic Nikel(II) complexes. In the metal complexation, it was observed that Salpn macrocyclic ligand can adopt more than a metal ion giving an unique multinuclear metal complexes including Ni(II)Salpn and $Ni(II)_3(Salpn)_2$. Characteristic IR ${\upsilon}(M-O)$ peaks for Ni(II)Salpn and $Ni(II)_3(Salpn)_2$ were observed to be $1028cm^{-1}$ and $1024cm^{-1}$, respectively. Characteristic UV-Vis absorption ${\lambda}_{max}$ peaks for $Ni(II)_3(Salpn)_2$ were observed to be 241nm and 401 nm. Structural characterization of $Ni(II)_3(Salpn)_2$ by NMR exhibits that the salicylidene ring moiety has two different resonance signals originated from the magnetically asymmetric diligand and trinuclear bis complex. Complete NMR signal assignments and characterizations elucidating structural features of $Ni(II)_3(Salpn)_2$ were described in detail.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.466-466
• /
• 2013

Quantum-dot materials have introduced novel applications in organic light-emitting diodes and solar cells. The size controllability and structure modifications have continuously been upgrading the applicability to optoelectronic and flat-panel displays. In particular, quantum-dot organic light-emitting diodes (QLEDs) are a device driven through the electrical field applied to the electrical diodes. The QLEDs are affected by the constituent materials and the corresponding device structures. Conventionally, the electrical properties are characterized only in terms of dc-based current-voltage characteristics. The dynamic change in light-emitting diodes should be characterized in emitted and non-emitted states. Therefore, the frequency-dependent impedance can offer different information on the electrical performance in QLED. The current work reports an auxiliary information on the electrical and optical features originating from quantum-dot organic light-emitting diodes. The empirical characterizations are discussed towards an experimental tool in optimizing the light-emitting diodes.

• Journal of Powder Materials
• /
• v.11 no.6 s.47
• /
• pp.515-521
• /
• 2004

Fe(C) nanocapsules were prepared by the chemical vapor condensation(CVC) process using the pyrolysis of iron pentacarbonyl $(Fe(CO)_5)$. Their characterizations were studied by means of X-ray diffraction, X-ray photoelectron spectrometer and transmission electron microscopy. The long-chained Fe(C) nanocapsules hav-ing the mean size of under 70 nm could be obtained below $1100^{\circ}C$ in different gas flow rates. The particle size of the powders was increased with increasing decomposition temperature, but it was decreased with increasing CO gas flow rate. The Fe powders produced at $500^{\circ}C$ consisted of three layers of ${\alpha}$-Fe/$Fe_3C$/amorphous phases, but it had two phase core-shell structure which consited of $Fe_3C$ phase of core and graphite of shell at $1100^{\circ}C$.

• Honam Mathematical Journal
• /
• v.36 no.3
• /
• pp.569-596
• /
• 2014

In several applied disciplines like control engineering, computer sciences, error-correcting codes and fuzzy automata theory, the use of fuzzied algebraic structures especially ordered semi-groups and their fuzzy subsystems play a remarkable role. In this paper, we introduce the notion of (${\in},{\in}{\vee}\bar{q}_k$)-fuzzy subsystems of ordered semigroups namely (${\in},{\in}{\vee}\bar{q}_k$)-fuzzy generalized bi-ideals of ordered semigroups. The important milestone of the present paper is to link ordinary generalized bi-ideals and (${\in},{\in}{\vee}\bar{q}_k$)-fuzzy generalized bi-ideals. Moreover, different classes of ordered semi-groups such as regular and left weakly regular ordered semigroups are characterized by the properties of this new notion. Finally, the upper part of a (${\in},{\in}{\vee}\bar{q}_k$)-fuzzy generalized bi-ideal is defined and some characterizations are discussed.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.122-128
• /
• 2000

Aerodynamic optimization of an automotive air-conditioning blower is a hard task because of the highly complex flow phenomena related to three-dimensional flow separations and the unsteady nature caused by the interaction between primary and secondary air flows throughout the fan. In this paper, an aerodynamic study on a forward-curved centrifugal fan has been carried out Firstly we obtained the fan performance curves versus flow rates showing its unstable nature in the surging operation range. Secondly aerodynamic characterizations were carried out by investigating the velocity and pressure fields in the casing flow passage using a 5-hole pilot probe, at different operating conditions. Surface flow pattern near the cut-off area exhibits similar flow behavior above the best efficiency operating point, although the pressure level increases substantially with the Increase of flow rate. Vorticity in the casing passage flow occurs in all (low rates, downstream from the r-Z plane $\theta$=120 deg., where the position of its core changes with the circumferential location. Although complex, the general flow behavior were common, giving insight in its main aerodynamic features.