• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.206-214
• /
• 2005

Heterogeneously-catalyzed oxidation of aqueous phase trichloroethylene (TCE) over supported metal oxides has been conducted to establish an approach to eliminate ppm levels of organic compounds in water. A continuous flow reactor system was designed to effect predominant reaction parameters in determining catalytic activity of the catalysts for wet TCE decomposition as a model reaction. 5 wt.% $CoO_x/TiO_2$ catalyst exhibited a transient period in activity vs. on-stream time behavior, suggesting that the surface structure of the $CoO_x$ might be altered with on-stream hours; regardless, it is probable to be the most promising catalyst. Not only could the bare support be inactive for the wet decomposition reaction at $36^{\circ}C$, but no TCE removal also occurred by the process of adsorption on $TiO_2$ surface. The catalytic activity was independent of all particle sizes used, thereby representing no mass transfer limitation in intraparticle diffusion. Very low TCE conversion appeared for $TiO_2$-supported $NiO_x$ and $CrO_x$ catalysts. Wet oxidation performance of supported Cu and Fe catalysts, obtained through an incipient wetness and ion exchange technique, was dependent primarily on the kinds of the metal oxides, in addition to the acidic solid supports and the preparation routes. 5 wt.% $FeO_x/TiO_2$ catalyst gave no activity in the oxidation reaction at $36^{\circ}C$, while 1.2 wt.% Fe-MFI was active for the wet decomposition depending on time on-stream. The noticeable difference in activity of the both catalysts suggests that the Fe oxidation states involved to catalytic redox cycle during the course of reaction play a significant role in catalyzing the wet decomposition as well as in maintaining the time on-stream activity. Based on the results of different $CoO_x$ loadings and reaction temperatures for the decomposition reaction at $36^{\circ}C$ with $CoO_x/TiO_2$, the catalyst possessed an optimal $CoO_x$ amount at which higher reaction temperatures facilitated the catalytic TCE conversion. Small amounts of the active ingredient could be dissolved by acidic leaching but such a process gave no appreciable activity loss of the $CoO_x$ catalyst.

• Journal of Bio-Environment Control
• /
• v.27 no.3
• /
• pp.222-230
• /
• 2018

This study aimed to determine effects of light-emitting diodes on plant growth, leaf morphology and cell elongation of two cultivars ('World-star' and 'Sushiro') of Spinacia oleracea. Plants were grown in a NFT system for 25 days after transplanting (DAT) under the LEDs [White (W), Red and Blue (RB, ratio 2:1), Blue (B), Red (R) LED] under the same light intensity and photoperiod ($130{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, 12 hours). The 'World-star' variety was significantly higher in shoot fresh and dry weights, leaf number, and leaf area than the 'Sushiro' variety. For the 'World-star' variety, the two treatments of mixed light (RB) and red light (R) showed a 35% higher shoot dry weight than that of blue light (B) and white light (W) at 25 DAT. In the 'Sushiro' variety, mixed light (RB) treatment, which had the highest shoot fresh and dry weights, showed 40% higher than the white light (W) treatment, which had the lowest shoot fresh and dry weights. Both varieties showed leaf epinasty symptom at 21 DAT only in both mixed light (RB) and red light (R), and red light (R) treatment showed significantly higher symptom than mixed light (RB), indicating the leaf epinasty is associated with red light. Microscopic observations of the cell size in the leaf center and edge parts showed that the cell density of leaf edge under the red light (R) was lower than that in leaf center, supporting previous reports that suggest an association of the cell size difference between the leaf center and edge with the leaf epinasty occurrence. Since the blue light (B) plays a role in alleviating the epinasty symptom caused by the red light (R), it seems necessary to identify the appropriate mixing ratio of the two light sources. In addition, the World-star variety seems to be more suitable for the cultivation of plant factory using LED light sources.

• Journal of Bio-Environment Control
• /
• v.27 no.4
• /
• pp.371-380
• /
• 2018

Aim of this study was to investigate the effects of different nutrient solutions and various light qualities generated by LED on the growth and glucosinolates contents of watercress (Nasturtium officinale) grown under hydroponics for 3 weeks. The seeds of watercress were sown on crushed rockwool media and raised them for two weeks. They were transplanted in a semi-DFT (deep flow technique) hydroponics system. A controlled-environment room was maintained at $20{\pm}1^{\circ}C$ and $16{\pm}1^{\circ}C$ temperatures and $65{\pm}10%$ and $75{\pm}10%$ relative humidity (day and night, respectively), with a provided photosynthetic photon flux density (PPFD) of $180{\pm}10{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ and a photoperiod of 16/8h. To find out the best kinds of nutrient solutions for growing watercress, Otsuka House 1A (OTS), Horticultural Experiment Station in Korea (HES), and Netherland's Proefstaion voor Bloemisterij en Gasgroente (PBG) were adapted with initial EC of $1.0-1.3dS{\cdot}m^{-1}$ and pH of 6.2, irradiating PPFD with fluorescent lamps (Ex-1). Either monochromatic (W10 and R10) or mixed LEDs (R5B1, R3B1, R2B1G1, and W2B1G1) were irradiated with a differing ratio of each LED's PPFD to understanding light quality on the growth and glucosinolates contents of watercress (Ex-2). Although significant difference in the shoot growth of watercress was not found among three nutrient solutions treatments, but the root fresh weight increased by 13.7% and 55.1% in PBG and OTS compared to HES, respectively. OTS increased the gluconasturtiin content by 96% and 65% compared to PBG and HES. Compared with the white light (W10), the red light (R10) showed a 101.3% increase in the shoot length of watercress. Increasing blue light portion positively affected plant growth. The content of total glucosinolates in watercress was increased by 144.5% and 70% per unit dry weight in R3B1 treatment compared with R2B1G1 and W10 treatments, respectively. The growth and total glucosinolates contents of the watercress were highest under R3B1 among six light qualities.

• Progress in Medical Physics
• /
• v.17 no.1
• /
• pp.47-53
• /
• 2006

The accuracy of the dosimetry in the Cyberknife system is accomplishing important role from all processes of the stereotactic radiosurgery. In this study, we estimated relative output factors for Cyberknife. All measurements were peformed by six different detectors: diode detector, X-Omat V film, Gafchromic EBT film, 0.015 cc, 0.125 cc and 0.6 cc ionization chamber The diode detector and three ionization chambers peformed using water phantom at 80 cm SSD and 1.5 cm depth. When the film measurements were peformed, the water phantom was replaced with a solidwater phantom. Each collimator normalized with respect to the output factor of the largest collimator (60 mm). For the collimators over than 30 mm, the output factors from the different detectors showed a good agreement within 0.5% except 0.6 cc ion chamber For the collimators less than 15 mm, there were substantial differences In the output factors among different detectors. That is, the value of output factor for the 5 mm collimator of a diode and Gafchromic film was each $0.656{\pm}0.009$ and $0.777{\pm}0.013$. In the ion chamber and diode detector, those difference were due to the presence of large dose gradients and lack of electronic equilibrium in narrow megavoltage x-ray beams Therefore, the Gafchromic EBT film were considered more accurate than the others detectors.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.233-241
• /
• 2014

The aim of this study is to develop a new software tool for 3D dose verification using $PRESAGE^{REU}$ Gel dosimeter. The tool included following functions: importing 3D doses from treatment planning systems (TPS), importing 3D optical density (OD), converting ODs to doses, 3D registration between two volumetric data by translational and rotational transformations, and evaluation with 3D gamma index. To acquire correlation between ODs and doses, CT images of a $PRESAGE^{REU}$ Gel with cylindrical shape was acquired, and a volumetric modulated arc therapy (VMAT) plan was designed to give radiation doses from 1 Gy to 6 Gy to six disk-shaped virtual targets along z-axis. After the VMAT plan was delivered to the targets, 3D OD data were reconstructed from 512 projection data from $Vista^{TM}$ optical CT scanner (Modus Medical Devices Inc, Canada) per every 2 hours after irradiation. A curve for converting ODs to doses was derived by comparing TPS dose profile to OD profile along z-axis, and the 3D OD data were converted to the absorbed doses using the curve. Supra-linearity was observed between doses and ODs, and the ODs were decayed about 60% per 24 hours depending on their magnitudes. Measured doses from the $PRESAGE^{REU}$ Gel were well agreed with the TPS doses at central region, but large under-doses were observed at peripheral region at the cylindrical geometry. Gamma passing rate for 3D doses was 70.36% under the gamma criteria of 3% of dose difference and 3 mm of distance to agreement. The low passing rate was resulted from the mismatching of the refractive index between the PRESAGE gel and oil bath in the optical CT scanner. In conclusion, the developed software was useful for 3D dose verification from PRESAGE gel dosimetry, but further improvement of the Gel dosimetry system were required.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.210-217
• /
• 2014

This study investigated the dosimetric effects of different dose calculation algorithm for lung stereotactic ablative radiotherapy (SABR) using flattening filter-free (FFF) beams. A total of 10 patients with lung cancer who were treated with SABR were evaluated. All treatment plans were created using an Acuros XB (AXB) of an Eclipse treatment planning system. An additional plans for comparison of different alagorithm recalcuated with anisotropic analytic algorithm (AAA) algorithm. To address both algorithms, the cumulative dose-volume histogram (DVH) was analyzed for the planning target volume (PTV) and organs at risk (OARs). Technical parameters, such as the computation times and total monitor units (MUs), were also evaluated. A comparison analysis of DVHs from these plans revealed the PTV for AXB estimated a higher maximum dose (5.2%) and lower minimum dose (4.2%) than that of the AAA. The highest dose difference observed 7.06% for the PTV $V_{105%}$. The maximum dose to the lung was also slightly larger in the AXB plans. The percentate volumes of the ipsilateral lung ($V_5$, $V_{10}$, $V_{20}$) receiving 5, 10, and 20 Gy were also larger in AXB plans than for AAA plans. However, these parameters were comparable between both AAA and AXB plans for the contralateral lung. The differences of the maximum dose for the spinal cord and heart were also small. The computation time of AXB plans was 13.7% shorter than that of AAA plans. The average MUs were 3.47% larger for AXB plans than for AAA plans. The results of this study suggest that AXB algorithm can provide advantages such as accurate dose calculations and reduced computation time in lung SABR plan using FFF beams, especially for volumetric modulated arc therapy technique.

• Tuberculosis and Respiratory Diseases
• /
• v.39 no.6
• /
• pp.502-510
• /
• 1992

Background: Neuron specific enolase (NSE) is a neuronal form of the glycolytic enzyme enolase which was first found in extracts of brain tissue, and later in a variety of APUD cells and neurons of the diffuse endocrine system. SCLC shares many APUD properties with normal neuroendocrine cells. NSE immunostaining and serum NSE measurement may be a useful marker of neuroendocrine differentiation in lung tumors and diagnosis of small cell carcinoma. Methods: NSE immunohistochemical staining was done and at the same time serum NSE levels were measured in 22 small cell lung cancer and 21 non small cell lung cancer which were confirmed histologically. Results: 1) NSE immunoreactivity was detected in 9 of the 18 (50%) small cell lung cancer, in 5 of the 16 non small cell lung cancer. 2) Whereas the mean value in non-small cell lung cancer group was $11.79{\pm}4.47\;ng/ml$, the mean level of serum NSE in small cell lung cancer increased up to $59.3{\pm}77.8\;ng/ml$. In small cell lung cancer patients, mean value of limited disease group was $20.19{\pm}12.91\;ng/ml$, while mean value of extended disease group was $91.9{\pm}94.2\;ng/ml$ showing statistically significant difference. If serum levels above 20 ng/ml were tentatively defined as positive, 16 of 22 (73%) patients with SCLC had positive serum NSE level, but only one patient with NSCLC did. There was no correlation between serum NSE level and immunoreactivity of NSE. Conclusion: These studies indicate that serum NSE measurement may be a useful marker for the diagnosis and disease extent and NSE immunostaining can be used to demonstrate the neuroendocrine components of lung tumor.

• Tuberculosis and Respiratory Diseases
• /
• v.50 no.1
• /
• pp.76-83
• /
• 2001

Background : Coal workers' pneumoconiosis is a fibrotic lung disease resulting from chronic inhalation of coal dust. The precise mechanism of lung fibrosis in coal workers' pneumoconiosis is uncertain. However, a relationship between the stimulation of fibroblast proliferation and collagen production by mediators released from in flammatory and resident lung cells is thought to be a major factor. The transforming growth factor-$\beta$(TGF-$\beta$), a multifunctional cytokine and growth factor, plays a key role in the scarring and fibrotic processes due to its ability to induce extracellular matrix proteins and modulate the growth and immune function of many cell types. To determine the involvement of TGF-$\beta$ in the development of lung fibrosis in coal workers' pneumoconiosis, the TGF-${\beta}_1$ level in plasma was measured in patients with coal workers' pneumoconiosis. Methods : Plasma was collected from 40 patients with coal workers' pneumoconiosis (20 with simple coal workers' pneumoconiosis and 20 with complicated coal workers' pneumoconiosis) and from 10 normal controls. The ELISA method was used to measure the plasma TGF-${\beta}_1$ concentration. Results : Compared to the control group ($0.63{\pm}01.8$ ng/mL), there was no significant difference in the plasma TGF-${\beta}_1$ level in patients with simple coal workers' pneumoconiosis ($0.64{\pm}0.17$ ng/mL) (p>0.05). However, in patients with complicated coal workers' pneumoconiosis the plasma TGF-${\beta}_1$ level ($0.79{\pm}0.18$ ng/mL) was significantly higher than in patients with simple coal workers' pneumoconiosis and the control group (p<0.05). Conclusion : The data suggests that TGF-${\beta}_1$ has some influence in the development of lung fibrosis in coal workers' pneumoconiosis.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.28-40
• /
• 2010

Purpose: The aim of this retrospective study was to provide long-term data about the correlation between multifactorial local factors and the survival of implants. Material and methods: During 19 years (1991 to 2009), 2796 implants were placed in 879 patients. From dental charts and radiographs, the following data were collected: patient's age at implant placement, gender, implant system, surface, length, diameter, location of implant placement, bone quality, primary stability, type of prosthesis. The correlations between these data and implant survival were analyzed. Statistical analysis was performed using Kaplan-Meier survival analysis, Chi-square test, odds ratio. Results: 1. Among the 2796 implants, 150 implants failed that resulted in a cumulative survival rate of 94.64%. The cumulative survival rate of smooth surface implants (91.76%) was lower than rough surface implants (96.02%). 2. Anatomic location, implant surface, diameter of smooth surface implant, primary stability, type of prosthesis, patient's age and gender were significantly associated with implant survival (P < .05). 3. No significant difference in implant survival was found in relation to the following factors: implant length, bone quality, diameter of rough surface implants and type of rough surface according to implant manufacturer (P < .05). Conclusions: Local factors such as anatomic location, implant surface, diameter of smooth surface implant, primary stability and type of prosthesis have a significant effect on implant survival.

• Child Health Nursing Research
• /
• v.2 no.2
• /
• pp.45-57
• /
• 1996

A serious disease in a family influences the entire family member given the fact that the members closely interact with each other. Especially in terms of pediatric nursing, study on family gains importance as the need to care of families whose children with developmental disabilities and chronic disease This study was done based on The Resiliency Model of Family Adjustment and Adaptation(McCubbin, 1991) is intended to examine the stress of parents whose children suffer from cleft lip or /and cleft palate. It also helps them to cope with the stress and analyze the relationship between the stress and coping This study used Family Inventory of Life Events and Changes (FILE) and Coping Health Inventory for Parents(CHIP) for measuring family stress and coping. The two instruments are revised to fit the social and cultural environment of Korean culture. Data collection was done from April 18, 1996 to May 18, 1996 at 8 University medical centers located in Seoul. Those who answered questionnaires were 84 parents whose children have cleft lip or /and cleft palate. SPSS PC+ was used to analyze the data collotted. Programs used for data analysis were t-test, ANOVA, Pearson correlation coefficient. The study is summarized as follows .1. The average score of family stress is 10.46(percentage of the full score 24.90) and 'finance and business strains'(3.25), and 'intrafamily strains'(2.65) ranked the highest. The average score of family's coping is 1.93, which is close to the answer of' moderately helpful' and they are measured to put their utmost efforts to' intergration and cooperation of family and optimistic definition on the situation'. 2. There is no significant statistical correlation between the family stress and coping. 3. Mothers show more stress than fathers in the parts of 'illness and family care strains' and 'losses'(t〓-2.34, t〓-2.32, p<.05). 4. Fathers show more willingness to cope with the stress than mothers do in the parts of' seeking social support','self-esteem','emotional comfort' 5. Mothers are more stress than fathers in the parts of family stress and its coping with it by usual traits(t〓-2.78, p<.05). Parents with religion are measured to cope more willingly than those who are not 6. Income of a family shows positive correlationship with family coping (r〓.28, p<.05). The study shows that gender difference is significant variable in studying on family stress and coping. Mothers get more stress than fathers, which has much to do with the fact that they are in charge of raising children and keeping houseworks. Accordingly, managing family crisis and its survival can be induced by giving support for the mothers, studying fathers including the rest of the family members and giving nursing care and arbitration ; religious background is also considered to be one of the important factors in family stress , judging from the relationship between family income and family's coping, caring given to suffering children is needed on societal levels. The above considerations bring up the need to have a longitudinal study of children with congenital anomaly including cleft lip or /and cleft palate and their families about family stress and coping. Resiliency programs on family system and their effectiveness and the relationship between the enlarged families with social and cultural values reflecting Korean tradition are also needed to be studied.