• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.582-585
• /
• 2004

Pb0.5Sr0.5TiO3 (PST) thin films were fabricated by the alkoxide-based sol-gel process using spin-coating method on Pt/Ti/SiO2/Si substrate. The PST films annealed from 500C to 650C for 1h show a perovskite phase and dense microstructure with a smooth surface. The grain size and dielectric constant of PST films increases with the increase in annealing temperature, which reduces the SiO2 equivalent thickness of the PST film. The crystallinity or internal strain in the PST thin films analyzed from the diffraction-peak widths correlate well with the decrease in the dielectric losses. The dielectric constants and dielectric loss (%) of the PST films annealed at 650c (teq : 0.89 nm) were 549 and 0.21%, respectively.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.845-847
• /
• 1999

(Ba, Sr)$TiO_3$[BST] thin films were fabricated on Pt/$TiO_2/SiO_2$/Si substrate by RF sputtering. The structural and dielectric properties of the BST thin films were investigated with the deposition time. Increasing the deposition time from 20 min. to 60 min., second phases were decreased, and EST (111), (100), (200) peaks were increased. The relative dielectric constant and dielectric loss of the EST thin films with the thickness of 3000$\AA$ were 300 and 0.018, respectively at 1[kHz]. The relative dielectric constants was decreased and dielectric losses was increased as increasing the frequency.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.92-96
• /
• 2003

Dielectric apertures in vertical cavity laser have been used for improved device performance. Numerical analysis is used to estimate the optical losses as the aperture diameter is reduced. The optical losses depend on the aperture size, thickness and location. The optical loss strongly depend on the aperture size and thickness when the aperture size is similar or smaller than the emitted wavelength. The optical loss is negligible and not depend on the aperture thickness when the aperture size is larger than 5 times emitted wavelength.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1636-1638
• /
• 1999

In this paper, humidity and temperature were carried out on XLPE sheet and XLPE/semi sheet. We measured voltage, temperature dependency and dielectric properties of humid dielectric materials. Dielectric losses of XLPE(A,B)/semi with and without humidity were $4.2{\times}10^{-4}$ and $3.6{\times}10^{-4},\;2.8{\times}10^{-4}$ and $3.2{\times}10^{-4}$, respectively, at room temperature. On the condition that humidity and semiconductors exist, we confirmed that dielectric properties had been influenced on semiconductor and humidity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.743-745
• /
• 2002

Pyroelectric and dielectric properties of modified PZT thin film and bulk ceramics were studied. In case of bulk specimens were prepared by conventional ceramic process and thin films with same composition and (111) preferred orientation were prepared by the sol-gel process. Their crystal structure, pyroelectric and dielectric properties were investigated after poling at $150^{\circ}C$ for 30 min for bulk ceramics and no poling treatment, respectively. Dielectric constants and losses of bulk and thin film were 600, 875 and 0.028, 0.025, respectively. Pyroelectric coefficients obtained were $50nC/cm^2K$ and $30nC/cm^2K$, respectively.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.21-26
• /
• 1997

The dielectric effects on the parasitics of bondwires buried in slightly-lossy dielectric materials hav been investigated over a wide frequency range using the method of moments with incorporation of ohmic and dielectric losses. The FR-4 composite is widely used as a basis material for PCB and plastic packages, because of it sinherent electricl and chemical stbility and low cost. The cole-cole model, which is representative complex permittivity model of epoxy polymers, has been applied to consider the dielectric effects in the MoM calculation. The prasitic impedance of a grounded bondwire in FR-4 composite is greatly increased due to the dielectric loading effect enhanced by the radiation at high frequencies. These calculation results will be helpful for designing and packaging of high-frequency low-cost IC's.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.91-98
• /
• 2004

This paper proposes a PCB plane model for generic SPICE circuit simulators. The proposed model reflects two frequency-dependent losses, namely skin and dielectric losses. After power/ground plane pair is divided into arrays of unit-cells, each unit-cell is modeled using a transmission line and two loss models. The loss model is composed of a resistor for DC loss, series HL ladder circuit for skin loss and series RC ladder circuit for dielectric loss. To verify the validity of the proposed model, it is compared with SPICE ac analysis using frequency-dependent resistors. Also, we show that the estimation results using the proposed model have a good correlation with that of VNA measurement for the typical PCB stack-up structure of general desktop PCs. With the proposed model, not only ac analysis but also transient analysis can be easily done for circuits including various non-linear/linear devices since the model consists of passive elements onl.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.257-260
• /
• 2006

This paper presents electromagnetic finite element analysis of power cables for wind turbine application. Eddy current losses are calculated due to high currents along metallic part, and dielectric strength on power cables is investigated for case study, which suggests the optimal cabling configuration for wind turbine construction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.119-122
• /
• 2003

This paper describes characteristics for insertion losses of Isolator have an effect on material parameter. One purpose of the paper is to present insertion loss on this resonator for magnetic loss, dielectric loss, magnetic field and saturation magnetization. Another is to study the effect of propeller resonator on response characteristics. In this paper, the analysis and measurement of the response characteristics were carried out for the isolator prototype. The measurement results agreed on the simulation results and acquire insertion loss $0.18\;{\sim}\;0.24dB$, return loss 27dB, isolation 27dB and bandwidth 500MHz on this condition saturation magnetization 550G, dielectric loss 0.0004, magnetic loss 20 and dielectric constant 14.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1202-1204
• /
• 1997

In this paper we evaluated dielectric properties and temperature dependency in PET with and without semiconductor. Dielectric losses of PET without and with semiconductor was $3.7{\times}10^{-3}$(%) and $1.8{\times}10^{-3}$(%), respectively, at room temperature. On the condition that semiconductors exist, we confirmed that dielectric properties had been influence on semiconductor's number.