• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.99-102
• /
• 2004

In rheo forming process, slurry making is very important factor because the microstructure of slurry affects the quality of final products. To control the microstructure of slurry, slurry making by new rheo die casting was studied. In new rheocasting method, processes parameters are degree of overheat in molten metal, cooling condition, high frequency induction heating condition and cup temperature. Microstructures according to these parameters were observed. By image analysis, equivalent diameter and roundness of grain were investigated and discussed. To find out mechanical properties of grain controlled aluminum part by rheo die casting, tensile tests were carried out to the T6 heat treatment.

• Journal of Korea Foundry Society
• /
• v.30 no.6
• /
• pp.205-209
• /
• 2010

This study evaluates the influence of strontium addition and holding time on mechanical properties for Al-10.5wt%Si-2wt%Cu secondary die-casting alloy and the measured electrical conductivity of modified alloys. A general improvement in the mechanical properties of the alloy was observed after adding the strontium. Ultimate tensile strength, elongation and electrical conductivity of modified alloys were improved by increasing strontium content and holding time. From these results, the optimal strontium content and holding time were identified on the mechanical properties of Al-10.5wt%Si-2wt%Cu secondary die-casting alloys.

• Journal of Korea Foundry Society
• /
• v.19 no.6
• /
• pp.484-492
• /
• 1999

The microstructures and mechanical properties of high strength yellow brass, Al bronze and Sn bronze alloys fabricated by gravity die casting and squeeze casting were investigated. A rapid cooling of casting was enhanced by pressure applied during solidification of Cu alloys, the cooling rate of casting was more great for high strength yellow brass alloy than other Cu alloys. Grain size and phases of the squeeze cast products become refined to 1/2 level compared to gravity die castings. Squeeze cast Al bronze and high strength yellow brass has about 10-20% higher yield and tensile strength and slighter decreased or nearly same elongation, compared to gravity die cast ones. Sn bronze has nearly same strength and hardness, but shows increased in elongation, compared to gravity die cast ones.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1709-1718
• /
• 2002

It is well recognized that improving capacity of positive grid in battery is one of key factors for controlling the expected long lift-time of Battery Energy Storage System(B.E.S.S). Thus it is really important to characterized material properties of positive grid which are mainly affected by fabrication process. In this study, two kinds of positive grids, which were fabricated by gravity casting and die-casting technique were used. Micro-structural observation and tensile test were conducted to investigate the effect of fabrication process of positive grid. Ultrasonic measurement based on pulse-echo method and ultrasonic C-scan technique also performed to correlate ultrasonic velocity with porosity ratio in positive grid. It was found that the porosity ratio of grid fabricated by gravity casting technique increased significantly compared to the grid fabricated by die-casting technique. It was also shown that ulrasonic technique is effective to evaluate the porosity ratio in positive grid.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.435-436
• /
• 2009

In the effort on cost reduction in marine equipment company, the medium sized impeller blade ($500mm{\times}200mm{\times}20mm$) of an axial flow pan was manufactured by the high pressure die casting, with which was replaced the gravity die casting. High pressure die casting is a practical alternative because of some advantages such as excellent accuracy and smooth cast surface as well as cost reduction if a certain amount of porosity in the parts can be minimized. In order to reduce the porosity in the center of the neck which is thickest region of the impeller blade, the several gate designs were proposed in this work. The flow simulations for each gate design were performed and then the optimal design was determined by considering the air pressure distribution in neck section. Finally, the size of porosity in the neck of the die cast impeller blade for optimal design was less than 1mm, which satisfied the requirement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.367-368
• /
• 2013

• Journal of Korea Foundry Society
• /
• v.31 no.3
• /
• pp.101-105
• /
• 2011

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.329-338
• /
• 2020

In this study, three different die geometries were selected to understand the die characteristics in the film casting extrusion processes. First, large and small-scale T-dies were numerically simulated to observe the scaled-down effect on the flow inside the dies. Second, three different dies-keyhole, linear tapper coat-hanger die (LTCD), and curved tapper coat-hanger die (CTCD)-were numerically observed and discussed according to the mass flow rate. Finally, the die exit velocity profiles and die characteristics were observed and discussed based on the power-law index for the LTCD die. These numerical simulations and numerical data will aid the optimization of the die design in industrial fields.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.45 no.4
• /
• pp.157-166
• /
• 2022

In the case of a die-casting process, defects that are difficult to confirm by visual inspection, such as shrinkage bubbles, may occur due to an error in maintaining a vacuum state. Since these casting defects are discovered during post-processing operations such as heat treatment or finishing work, they cannot be taken in advance at the casting time, which can cause a large number of defects. In this study, we propose an approach that can predict the occurrence of casting defects by defect type using machine learning technology based on casting parameter data collected from equipment in the die casting process in real time. Die-casting parameter data can basically be collected through the casting equipment controller. In order to perform classification analysis for predicting defects by defect type, labeling of casting parameters must be performed. In this study, first, the defective data set is separated by performing the primary clustering based on the total defect rate obtained during the post-processing. Second, the secondary cluster analysis is performed using the defect rate by type for the separated defect data set, and the labeling task is performed by defect type using the cluster analysis result. Finally, a classification learning model is created by collecting the entire labeled data set, and a real-time monitoring system for defect prediction using LabView and Python was implemented. When a defect is predicted, notification is performed so that the operator can cope with it, such as displaying on the monitoring screen and alarm notification.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.82-85
• /
• 2012

The effect of the alloy systems Al-Mg alloy and Al-Si alloy in this study on the characteristics of die-casting were investigated using solidification simulation software (MAGMAsoft). Generally, it is well known that the casting characteristics of Al-Mg based alloys, such as the fluidity, feedability and die soldering behaviors, are inferior to those of Al-Si based alloys. However, the simulation results of this study showed that the filling pattern behaviors of both the Al-Mg and Al-Si alloys were found to be very similar, whereas the Al-Mg alloy had higher residual stress and greater distortion as generated due to solidification with a larger amount of volumetric shrinkage compared to the Al-Si alloy. The Al-Mg alloy exhibited very high relative numbers of stress-concentrated regions, especially near the rib areas. Owing to the residual stress and distortion, defects were evident in the Al-Mg alloy in the areas predicted by the simulation. However, there were no visible defects observed in the Al-Si alloy. This suggests that an adequate die temperature and casting process optimization are necessary to control and minimize defects when die casting the Al-Mg alloy. A Tatur test was conducted to observe the shrinkage characteristics of the aluminum alloys. The result showed that hot tearing or hot cracking occurred during the solidification of the Al-Mg alloy due to the large amount of shrinkage.