• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.112-120
• /
• 2001

Poor fuel vaporization in gasoline engines causes the problem of HC emission during the cold start and warm-up period. This paper presents a strategy to improve fuel atomization during the warm-up phase. In this experiment, the heated fuel-rail system is constructed to investigate the effects of fuel heating on the average size of fuel droplets. The fuel atomization effects are examined by measuring Sauter Mean Diameter (SMD) of the fuel droplets from the three different types (two-hole, pintle, and six-hole) of injectors based upon a returnless heated fuel-rail system. The results show that the six-hole type injector is the most sensitive to fuel heating in terms of SMD among three different types of injectors.

• Laser Solutions
• /
• v.11 no.1
• /
• pp.25-31
• /
• 2008

The characteristics of femtosecond laser ablation of $Al_2O_3$ for prescision microfabrication are studied experimentally. Specifically, the process time during femtosecond laser drilling of microholes with $sub-100{\mu}m$ diameter are investigated for varying laser fluence, scan speed and beam path designs like trepanning with continuously changed start points. The accumulation of sub-micrometer size particles within the hole and the deterioration of edge clarity and roundness for decreasing hole diameter are examined and through process optimization the microdrilling with good hole quality is achieved using a femtosecond laser system (repetitionrate 1 kHz, wavelength 785 nm, pulse duration 185 fs)

• IE interfaces
• /
• v.12 no.2
• /
• pp.346-353
• /
• 1999

In this paper, the optimum drilling operation sequence which results into the minimum overall machining time required to produce a (multi-diameter) hole is identified. The operation sequence is defined as the set of ordered operations used for producing a (multi-diameter) hole. The overall machining time is derived by summing the minimum machining times of each operation assigned to a sequence. The operations represent the drilling actions of certain sizes to produce the related holes. The minimum machining time of each operation is obtained by solving the optimization problem. Finally, this paper will identify the effects of machining constraints on the overall machining times and their relationships to sequence selection.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1517-1521
• /
• 2007

On this study, technical aspects were reviewed to drill a series of micro holes (${\phi}$0.10) over 200 within a few micron tolerance in diameter and position on the stainless steel material. Dedicated tools & jigs were designed and manufactured and optimum cutting conditions were found. On this micro hole drilling process, guide drill and step feeding were applied to help chip discharge, prevent drill breakage and finally improve the accuracy of positioning and roundness. The processing results indicated that most holes are distributed within a few micron tolerance in diameter and position intervals.

• Journal of the Optical Society of Korea
• /
• v.9 no.4
• /
• pp.140-144
• /
• 2005

In this paper we have investigated the guiding properties of photonic crystal fibers (PCFs) with a square-lattice of air-holes in the cladding. We have shown numerical results of PCFs with various air hole sizes and hole-to-hole spacings over a wide wavelength range. The group velocity dispersion, effective area and effective refractive index of PCF have been calculated numerically. The waveguide dispersion has greatly affected the group velocity dispersion when hole-to-hole spacing is about $1{\mu}m$. The effective area is quite flat over the wide spectral range whether the hole-to-hole spacing is large or ratio of diameter to pitch is large. From the field distribution, we found that the field is tightly confined within the core region of PCF when the pitch is $3{\mu}m$ and the air-filling fraction is 0.9.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.96-104
• /
• 1994

The use of advanced composite materials has grown in recent years in aerospace and other structures. Out of various kinds of repairing methods the one selecteh for this study is an idealized case which simulates a situation where a damaged laminate has been repaired by drilling a hole and therefter plugging the hole with reinforcement. Two typesof reinforcement are investigated ;adhesively bonged plug reinforcement or snug-fit unbonded plug in the hole. For each case of reinforcement, four different sizes of hole diameter and three types of reinforcing material(steel, aluminum, plexiglass) are employed for investigation. The experiment are mainloy forced on the evaluation of ultimate strength of laminate with reinforced hole in comparison to its counterpart with the open hole.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.952-957
• /
• 2001

The objectives of this investigation were to obtain an excellent spray by cavitation under the low injection pressure. When cavitation occurs in the nozzle hole, the atomization of the liquid jet enhanced considerably. In this experiments, a acrylic nozzle made the gap and installed the bypass in the nozzle hole was used to enhance the atomization of the liquid jet at the low injection pressure. The liquid flow in the nozzle hole was photographed by a transmitted light using a micro flash. The spray angle was measured macroscope images of PMAS and the Sauter mean diameter was measured PDA system. To measure the pressure of the nozzle hole, pressure transducer was used. The results of this study indicated that enhanced atomization of the liquid jet at the low injection pressure was obtained by making the gap and installing the bypass at the single hole nozzle.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.3 no.1
• /
• pp.40-48
• /
• 2000

The term "deep holes" is used to describe the machining of holes with a relatively large length to diameter ratio. The main feature of BTA deep hole drilling is the stabilization of cutting force necessary for the self guidance of the drill head. An additional feature is the cutting tool edges that are unsymmetrically placed on the drill head. There is an increasing necessity to predict the hole geometry and other dynamic stability behavior of deep hole drilling guidance. In this study, the effects of BTA deep hole drilling conditions on the hole profile machined piece are analyzed using domain analysis technique. The profile of deep hole drilled work piece is related to cutting speed, feed rate, chip flow, tool wear, and so on. This study deals with the experimental results obtained during the BTA drilling on SM45C, SM55C carbon steels and SCM440 steels under various cutting conditions, and these results are compared with analytical evaluations.aluations.

• Journal of ILASS-Korea
• /
• v.7 no.1
• /
• pp.36-42
• /
• 2002

The objective of this investigation was to obtain an excellent spray at the low injection pressure. When cavitation occurred in the nozzle hole the atomization of the liquid jet enhanced considerably. In this experiments, a acrylic nozzle which was installed the gap and installed the bypass in the nozzle hole was used to enhance the atomization of the liquid jet at the few injection pressure. The liquid flow in the nozzle hole was photographed by a transmitted light using a micro flash. The spray angle was measured by macroscope images of PMAS and the Sauter mean diameter was measured by PDA system. The pressure of the notate hole was measured by pressure transducer. It was found that enhanced atomization of the liquid jet at the low injection pressure was obtained by installing the gap and the bypass at the single hole nozzle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.11 s.242
• /
• pp.1542-1550
• /
• 2005

This paper presents the numerical procedure for calculating non-uniform residual stresses based on relieved displacements obtained from incremental hole drilling. The relationship between the in-plane displacement produced by introducing a blind hole and the corresponding residual stress is established. Finite element calculations are described to evaluate the relieved coefficients required for the determination of non-uniform residual stresses. Validity of the proposed method has been tested through three axisymmetric test examples and two three-dimensional examples. As a result of . simulation on the test examples, it is found that this numerical procedure is well adopted to measuring non-uniform residual stress in the full hole depth range of the hole diameter from the surface. The accuracy of the hole drilling method with displacement measurement is discussed, comparing tile method with strain measurement