• 한국추진공학회지
• /
• 제12권2호
• /
• pp.48-56
• /
• 2008

액체로켓 예연소기의 산화제 과잉 연소는 매우 어려운 과업이다. 이를 위해서는 작동 조건에서 좋은 혼합특성을 갖는 분사기를 설계하는 것이 무엇보다 중요하다. 따라서 고압환경에서 로켓 산화제 과잉 예연소기용 분사기의 분무특성을 실험을 통해 알아보았다. 분사기는 연료 및 산화제 오리피스, 산화제 스커트로 구성되어있다. 분사기의 분무특성을 알아보기 위해 주위기체압력을 0에서 30kgg/cm2[g]까지 가압하여 분무 가시화, Sauter 평균 입경을 측정하였으며, 액적 크기는 이미지 처리 기법을 이용하였다. 실험결과로부터 로켓 산화제 과잉 예연소기용 분사기의 분무특성을 이해할 수 있었으며, 로켓 산화제 과잉 예연소기 개발에 중요한 자료로 활용될 수 있을 것이다.

• 한국항공우주학회지
• /
• 제47권3호
• /
• pp.204-211
• /
• 2019

희박연료 직접분사(Lean Direct injection(LDI)) 가스터빈 연소기에 대한 이상유동 특성을 해석하였다. LDI 연소기에 적용된 환형분사기(hollow-cone spray injector)의 분열을 모사하기 위해 분열모델(Linearized Instability Sheet Atomization(LISA), Aerodynamically Progressed Taylor Analysis Breakup(APTAB)을 적용하였다. 침투깊이와 평균입도(Sauter Mean Diameter(SMD))를 통해 분열모델을 검증하였으며, LDI 연소기에 적용하여 이상유동특성을 분석하였다. 스월인젝터로 인해 Precessing Vortex Core(PVC)가 발생하였으며, 액적들이 PVC를 따라 미립화되는 것을 확인하였다. SMD 결과를 통해 PVC가 회전하는 영역의 외곽으로 즉, 빠른 속도 영역에 액적들이 분포하며, 스톡스수(Stokes number)는 1보다 작다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1257-1262
• /
• 2014

The variances of atomization characteristics with the misalignment of injectors defined as the fraction of skewness for various angles of impingement and pressure conditions were studied using the doublet impinging injectors with a like-on-like arrangement. Water was used as simulant and the spray characteristics along with the changes in the skewness were analyzed using the methods of spray image photography. Experiment was carried for the impinging nozzles of orifice diameter of 1.2 mm within Reynolds numbers ranging from $9{\times}10^3-4.5{\times}10^4$ and the fraction of skewness considered for the experiment ranges from 0.0 to 0.9 at ambient temperature condition. Flat sheet with a distinct rim produced perpendicular to the plane of impinging jets goes ondisappear and sheet appears comparatively shorterwith the increase in fraction of skewness resulting the atomization of fluid droplet very close to impingement point with decrease in breakup length and increase in spray angle up to certain extent. The maximum allowable skewness was found as the result. The skewness up to the certain extent can be considered as the parameter to control the atomization characteristics of simulant inside the combustion chamberproviding the high economic performance of fuel and time.

• Journal of Mechanical Science and Technology
• /
• 제16권7호
• /
• pp.999-1008
• /
• 2002

The spray structures and distribution characteristics of liquid and vapor phases in non-evaporating and evaporating Gasoline Direct Injection (GDI) fuel sprays were investigated using Laser Induced Exciplex Fluorescence (LIEF) technique. Dopants were 2% fluorobenzene and 9% DEMA (diethyl-methyl-amine) in 89% solution of hexane by volume. In order to study internal structure of the spray, droplet size and velocity under non-evaporating condition were measured by Phase Doppler Anemometry (PDA). Liquid and vapor phases were visualized at different moments after the start of injection. Experimental results showed that the spray could be divided into two regions by the fluorescence intensity of liquid phase: cone and mixing regions. Moreover, vortex flow of vapor phase was found in the mixing region. About 5㎛ diameter droplets were mostly distributed in the vortex flow region. Higher concentration of vapor phase due to vaporization of these droplets was distributed in this region. Particularly, higher concentration of vapor phase and lower one were balanced within the measurement area at 2ms after the start of injection.

• 대한기계학회논문집B
• /
• 제25권5호
• /
• pp.688-696
• /
• 2001

Vaporizing characteristics of two GDI injectors with different spray angles were investigated using exciplex fluorescence method. Injector I has narrower spray angle, while injector II has wider one. The exciplex system of fluorobenzene and DEMA in a non-fluorescing base fuel of hexane was employed. In quantifying concentration of fuel vapor, quenching of concentration and temperature was corrected. Droplet size and velocity were also measured by PDPA under non-vaporizing condition. From obtaining the images of liquid and vapor phases, vaporizing GDI sprays could be divided as two regions: cone and mixing regions. For injector I, vortex region was not developed. High concentration of fuel vapor due to vaporization of many fine droplets was distributed near the spray axis. For injector II, droplets with the diameter of about 10 $\mu$m were distributed in the vortex region. The vortex region had high concentration of fuel vapor due to vaporization of these droplets. Particularly, higher and lower concentrations of fuel vapor were balanced at 2ms after the start of injection for injector II.

• Korean Chemical Engineering Research
• /
• 제44권3호
• /
• pp.235-242
• /
• 2006

분무 열분해법이란 전구체를 용해시킨 용액을 수 마이크론에서 수십 마이크론 크기의 액적으로 분무한 후, 용매를 증발시키고 석출된 전구체를 열분해하여, 입자 및 필름을 제조하는 공정이다. 이 분무 열분해법의 핵심 요소는 전구체,용매, 액적 제조 그리고 분해 반응기 등 4가지이다. 이 4가지 요소의 적절한 조합에 의해서 현존하는 거의 대부분의 입자와 필름을 제조할 수 있는 범용성이 높은 기술이다. 현재 기술 수준으로는 상업적인 성공을 거두기는 힘들지만 향후 다성분계의 입자나 필름, 혹은 고기능성 입자의 제조에 응용될 경우 매우 유용한 기술로 각광을 받을 전망이다. 본 총설에서는 이 분문 열분해법을 이용해서 만들어지는 입자 중에서 주로 형광체를 중심으로 지금까지 개발된 다양한 분무 열분해 공정 기술을 소개한다

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.183-192
• /
• 2014

In this work, the mixture formation and atomization characteristics of biodiesel fuel were reviewed under various test conditions for the optimization of compression-ignition engine fueled with biodiesel. To achieve these, the effect of nozzle caviting flow, group-hole nozzle geometry and injection strategies on the injection rate, spray evolution and atomization characteristics of biodiesel were studied by using spray characteristics measuring system. At the same time, the fuel heating system was installed to obtain the effect of fuel temperature on the biodiesel fuel atomization. It was revealed that cavitation in the nozzle orifice promoted the atomization performance of biodiesel. The group-hole nozzle geometry and split injection strategies couldn't improve it, however, the different orifice angles which were diverged and converged angle of a group-hole nozzle enhanced the biodiesel atomization. It was also observed that the increase of fuel temperature induced the quick evaporation of biodiesel fuel droplet.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.47-53
• /
• 2006

The purpose of this study was to investigate the significant characteristics in spray of industrial etch-nozzle for the design of process. The experiment was carried out with different spray pressure and industrial nozzle in wet etch. The characteristics of liquid spray, such as axial velocity and sauter mean diameter measurements were obtained by PDA. And impact force was calculated from spray characteristics. It was found that the fluid with higher spray pressure resulted in the smaller SMD and the higher droplet velocity and impact force. The depth of etch was increased in case of high spray pressure. In the case of injection angle oscillated between $20^{\circ}$, the result indicated constant effect of etch. The correlation between the spray characteristics and etch ones were analyzed. The depth of etch had good positive correlation with axial velocity and impact force. The result clearly shows that the characteristics in wet etch are strongly related to the spray characteristics with process.

• 한국추진공학회지
• /
• 제12권1호
• /
• pp.16-22
• /
• 2008

액체제트의 액적분열 분포특성을 알아보기 위해 아음속 유동 내로 수직 분사된 이유체 분무를 실험적으로 연구하였다. 노즐은 L/d=3의 외부혼합형을 사용하였으며 공기와 액체의 비를 $0\;{\sim}\;59.4%$까지 변화시키면서 분사하였다. 분무형상을 이미지화 하여 분무의 궤적과 분열특성을 관찰하였다. PDPA를 사용하여 액체제트 분열의 단면분포 특성을 측정하였으며 SMD, 액적속도, 그리고 체적유속을 측정하였다 이유체 분무로부터 공급되는 공기의 유량이 증가할수록 액체 제트의 충돌점은 노즐 입구와 좀 더 가까워졌으며, 침투거리는 증가하였고, 기체 액체 비를 증가시킴에 따라 좀 더 무화된 액체제트의 분포를 얻을 수 있었다.

• 한국대기환경학회지
• /
• 제34권1호
• /
• pp.177-186
• /
• 2018

It is a well-known fact that precipitation plays an important role in capturing ambient particles, however, the details of particle scavenging properties have not been fully proved. To clarify the particle scavenging properties, a complementary study was carried out with the bulk and semi-bulk rain samples collected in an urban city of Japan. pH showed a continued downturn for a little bit at the beginning rainfall and then a turn-up in the following rainfall. The recorded pH values of rainwater (ranged from 3.5-4.6) demonstrated that the strong acid rain was observed during our field measurements. Compared to the subsequent rainfall, electrical conductivity in the beginning rainfall had about 1.3 times higher level. Sulfur showed an overwhelmingly high concentration compared to other elements in both ambient total suspended particles (TSP) and rain samples. On the contrary to ambient TSP, every element including Ca and Zn in rain showed a continued rise in concentration accompanied by increasing of rainfall amount. During the first period of the rainfall there was no meaningful change in elemental carbon concentration, however, it was largely increased (up to $0.2mg\;L^{-1}$) in the sequential rainfall (4.0-4.5 mm rainfall amount). The theoretically calculated number concentration of particles scavenged by raindrops showed a strong decrease of with the increasing droplet diameter regardless of particle type.