• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.238-238
• /
• 2009

In this work, we investigated the effect of the Zn complex concentration and growth temperature on the growth of ZnO nanorod by hydrothermal method. The ZnO nanorods were performed at condition of the various Zn complex concentration and growth temperature, 0.02 ~ 0.08 M and 60 ~ 80 $^{\circ}C$, respectably. We found from the SEM results that the diameter and length of ZnO nanorods were with increasing the growth temperature and Zn complex concentration. However, the growth condition in the two parameters wasmore than sensitive compared to Zn complex concentration on increasing the growth rate. From photoluminescence(PL) analysis, the strong band-edge emission for ZnO nanorod grown at 80 $^{\circ}C$ with 0.08 M indicated the fine crystallinity. Therefore, the diameter and length of ZnO nanorods have been able to control through the control of front growth parameters. Also, these ZnO nanorods grown low temperature will be available as building block for transparence flexible device applications.

• 한국정밀공학회지
• /
• 제5권3호
• /
• pp.81-90
• /
• 1988

In recent, the requirement of remote control of hychaulic system is in- creasing. The actuator unit whose output position is proportional to input electrical signal needs a pressure reducer and a dump valve. The pressure reducer provides a constant regulated pressure and filters contaminants. The dump valve supplies proper pressure to the pressure reducer and unloads when the system is not operated. In this thesis, dump valve and pressure reducer with auxiliary function are studied. The choke in the pressure reducer prevents actuator from supplying higher pressure than necessary pressure at beginning, and the spring constant affects on the dynamic characterisics. In dump valve, it is proved that diameter of servo-slide hold and choke diameter of dump plunger affects on damping response.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.243-246
• /
• 2003

This paper presents a new motor design well suited for an advanced exercise bike. The advanced exercise bike setup high demands for performance and physical dimensions, which is high torque, wide speed range and a diameter/length ratio around 5. These requirements makes the new motor design called an E-core Transverse Flu Machine (ETFM) vev interesting because the segmented design of the stator and rotor poles enables high diameter without increasing the flux-path and since the ETFM is similar to the switched reluctance motor, high torque and wide speed range is possible. The design of the ETFM can be peformed using a developed design program, which is also introduced in the paper. A prototype of the exercise bike with the ETFM and a classical H-bridge converter with analog current control is constructed for verification of the concept.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.223-226
• /
• 2001

A SMA actuator fabricated in this paper generates the large force and it's structure is very simple. The SMA actuator was fabricated by small size with diameter of 4mm and length of 38mm and also it's actuations toward all the directions can be acquired because of three SMA springs which was fabricated with diameter of 1.2mm and 30 turns. We showed into applicability to smart catheter by analyzing accurately the dynamic characteristics such as heading angle, bending angle, force, displacement. For verifying control capacity of the fuzzy controller, we compared Fuzzy controller with PID controller by simulation.

• 제어로봇시스템학회논문지
• /
• 제17권5호
• /
• pp.412-418
• /
• 2011

The scale of wind turbines has continuously increased over the last decade. Especially, the rapid growth of the rotor diameter has brought about the increase of the tower height and the load on the rotor blade, as can be seen in the case of a 5MW class wind turbine with 126m rotor diameter. This trend means the increasing possibility of system failure. In addition to that, it is impossible for human operators to stay and manage all the turbines in the case of a large-scale wind farm. For these reasons, the operation and maintenance technology is getting more importance. In this paper, we present an unmanned remote monitoring system for MW class wind turbines and its application to YeungHeung wind test bed.

• 한국결정성장학회지
• /
• 제4권4호
• /
• pp.356-362
• /
• 1994

무게 측정에 의한 자동 직경 제어 방식의 Czochralski 단결정 성장 장칭를 제작하였다. 성장로의 몸체와 hot zone을 자체 설계, 제작하였으며, computer에 의하여 전자저울과 유도가열장치를 자동 제어하므로써 가열 공정에서 부터 냉각 공정까지의 모든 과정을 자동화시킬 수 있는 program을 개발하였다. 제작된 성장장치를 사용하여 $LiNbO_3$ 단결정을 성장시켜 성장 장치의 성능을 평가 하였다.

• 대한기계학회논문집A
• /
• 제41권1호
• /
• pp.41-48
• /
• 2017

최근 에너지, 바이오공학, 전자공학 등 다양한 분야에서 초미세 고분자섬유의 활용이 증대되고 있다. 이러한 고분자 섬유의 제작방법의 하나로서 전기방사법은 타 공정에 비해 공정장치가 간단하고 재료의 선택에 제한이 적은 등 다양한 장점을 가져 활발하게 사용되고 있다. 그러나 전기방사공정은 미세한 고분자 섬유가 전기장이 부가된 공기층을 통과하면서 높은 불안정성을 가지기 때문에 전기방사공정을 통해 제작되는 섬유매트의 형상 및 기하학적 특성의 조절이 어려운 단점을 가지고 있다. 본 연구에서는 서로 다른 두 가지 용매를 이용하여 섬유의 직경을 나노섬유와 마이크로섬유로 제작할 수 있음을 보였으며, 이를 조합하여 기계적 특성과 공극률을 조절할 수 있는 하이브리드 섬유매트를 제작할 수 있음을 보였다. 또한 제작된 매트를 이용하여 기계적 특성과 공극률이 조절될 수 있음을 확인하였다.

• 생물환경조절학회지
• /
• 제5권2호
• /
• pp.194-201
• /
• 1996

분구의 구경과 액분산기의 구조가 각각 다른 12종의 미니스프링클러를 대상으로 살수량과 살수강도분포를 실험하여 얻은 주요 결과는 다음과 같다. 미니 스프링클러의 살수량은 분구의 이론 유출량 산출 수식에 의해 예측할 수 있었다. 실험한 스프링클러의 유량계수는 분구구경 증가에 따라 감소하여 그 크기는 분구구경 0.8, 1.2, 1.6mm의 경우 각각 0.90-30.95, 0.80-0.82, 0.76-0.79의 범위로 나타났다. 스프링클러의 살수 분포는 동일한 구조의 스프링클러의 경우 분구구경이 작을 수록 그리고 살수압력이 낮을 수록 균일한 것으로 나타났다. 이러한 스프링클러의 살수분포는 분구구경이나 살수압력 외에도 액분산기의 구조에 따라 크게 영향을 받으므로 액분산기의 구조를 변화하므로서 살수입자의 최대 도달거리나 살수의 균일도를 높일 수 있음을 알 수 있었다.

• Journal of Forest and Environmental Science
• /
• 제30권2호
• /
• pp.218-225
• /
• 2014

Studies were carried out to standardize and develop a suitable macro-propagation technology for large scale production of superior clonal stock through stem cuttings in Commiphora wightii Arnott (Bhandari), a data deficient medicinal plant of arid region. For the purpose, three experiments were conducted. The first experiment was tried to elucidate the impact of various cutting diameters (0.50-0.75 cm, 0.75-1.00 cm, 1.00-1.50 cm, and >1.50 cm) in combination with varying growing conditions (sunlight, shade house and mist chamber) on shoot sprouting and rooting without using exogenous plant growth regulators. Cutting diameter (size 0.75-1.00 cm) in mist chamber has shown maximum sprouting (90.00%) and rooting (73.33%), primary root (6.67) and secondary root (16.67) followed by 1.00-1.51 cm in mist chamber. Minimum sprouting (40.00%), rooting (33.33%), number of shoot (1.33), primary root (1.00) and number of secondary root (1.00) was recorded in cutting diameter (size >1.50 cm) in sunlight. Second experiment was performed to find out optimum growth regulator concentration of rooting hormone (100, 200, 500 and 1000 ppm) of Indole-3-acetic acid (IAA) and Indole-3-butyric Acid (IBA) on adventitious root formation on cuttings diameter (size 0.25-0.50 cm) in comparison to control. Maximum rooting percentage (93.33%) was recorded in 200 ppm followed by 500 ppm (86.66%) of IBA as compared to control, which showed only 60 per cent sprouting. Third experiment was performed with newly formed juvenile micro-cuttings treated with varying concentrations of IAA and IBA. The juvenile cuttings (size 6-10 cm, basal dia <0.25 cm) were selected as micro-cuttings. The cuttings treated with IBA (500 ppm) showed 64.30% rooting as compared to other treatments. Results of above experiments indicate that cuttings (size 0.75-1.00 cm dia) may be developed in mist chamber for better performance. While using heavier cuttings, no growth promoting hormones is required however; growth regulator 200 ppm concentration of IBA rooting hormone was observed optimum for promoting macro-propagation in stem cuttings of lower diameter class (0.25-0.50 cm).

• 생물환경조절학회지
• /
• 제13권3호
• /
• pp.178-184
• /
• 2004

본 연구는 영상 처리를 이용하여 채소의 모종 시기를 자동으로 파악할 수 있는 시스템을 개발하기 위한 것이다 즉 작물의 높이, 장변 및 단변을 영상처리를 이용해 자동으로 측정하고자 하는 시스템을 개발하고자 한 것이다. 각 작물 당 20개씩의 실험체를 두어반복 측정한 결과, 들깨의 경우 높이는 평균 오차 5.0mm로 평균 실측 길이 대비 1.7% 오차율, 장변은 평균 오차 4.7mm, 오차율 3.9%, 단변은 평균 오차 5.5 mm, 오차율 6.9%로 나타났다. 도라지의 경우 높이는 평균 오차 2.4 mm, 오차율 8.1%, 장변은 평균 오차 3.4 mm, 오차율 7.2%, 단변은 평균 오차 4.0 mm, 오차율 10.4%로 나타났다. 상추의 높이는 평균 오차 4.0 mm, 오차율 9.1%, 장변은 평균 오차 3.4 mm, 오차율 7.2%, 단변은 평균 오차 3.6mm, 오차율 9.4%로 나타났다. 따라서 현장 환경에 맞게 좀 더 개선된다면 사람의 시각을 이용한 작물의 생장상태 판별보다 더 정확하다고 판단된다.