• The Journal of Advanced Prosthodontics
• /
• v.7 no.1
• /
• pp.69-75
• /
• 2015

PURPOSE. To compare the shear bond strength of various veneering materials to grade II commercially pure titanium (CP-Ti). MATERIALS AND METHODS. Thirty specimens of CP-Ti disc with 9 mm diameter and 10 mm height were divided into three experimental groups. Each group was bonded to heat-polymerized acrylic resin (Lucitone 199), porcelain (Triceram), and indirect composite (Sinfony) with 7 mm diameter and 2 mm height. For the control group (n=10), Lucitone 199 were applied on type IV gold alloy castings. All samples were thermocycled for 5000 cycles in $5-55^{\circ}C$ water. The maximum shear bond strength (MPa) was measured with a Universal Testing Machine. After the shear bond strength test, the failure mode was assessed with an optic microscope and a scanning electron microscope. Statistical analysis was carried out with a Kruskal-Wallis Test and Mann-Whitney Test. RESULTS. The mean shear bond strength and standard deviations for experimental groups were as follows: Ti-Lucitone 199 ($12.11{\pm}4.44$ MPa); Ti-Triceram ($11.09{\pm}1.66$ MPa); Ti-Sinfony ($4.32{\pm}0.64$ MPa). All of these experimental groups showed lower shear bond strength than the control group ($16.14{\pm}1.89$ MPa). However, there was no statistically significant difference between the Ti-Lucitone 199 group and the control group, and the Ti-Lucitone 199 group and the Ti-Triceram group. Most of the failure patterns in all experimental groups were adhesive failures. CONCLUSION. The shear bond strength of veneering materials such as heat-polymerized acrylic resin, porcelain, and indirect composite to CP-Ti was compatible to that of heatpolymerized acrylic resin to cast gold alloy.

• Korean journal of food and cookery science
• /
• v.23 no.6
• /
• pp.824-831
• /
• 2007

This study was conducted to investigate the quality characteristics of low-fat pork patties containing fat replacers. Pectin(PE) and potato starch(PO) were added as fat replacers and physicochemical properties of the patties were evaluated after oven-roasting or pan-frying. Uncooked and cooked pork patties formulated with the fat replacers were higher in moisture and ash content and lower in fat content than those of the control. The cooking yield and reduction in diameter of the patties were significantly improved by the addition of PE or PO and oven-roasting exhibited a higher cooking yield and lower reduction in diameter than pan-frying (p<0.05). Water holding capacity(WHC) and fat retention were highest in the patties formulated with PE, while the control had the lowest WHC when cooked by oven-roasting. The Hunter L (lightness) values were not different among the patties but the Hunter a (redness) and b (yellowness) values of the low fat pork patties were higher than those of the control and oven-roasting produced higher redness values than pan frying. Hardness and brittleness were lowest in the patties with PE, while cohesiveness and springiness showed no difference among the patties (p<0.05). The sensory analysis results showed that the use of PE or PO improved the overall acceptability of the low-fat pork patties. After 30 days of storage at $-20^{\circ}C$, pH and cooking yield decreased slightly, while hardness increased in all the patties.

• Korean Journal of Plant Resources
• /
• v.14 no.1
• /
• pp.48-52
• /
• 2001

The study was conducted to find effect of irrigation treatment during growth stage on growth and yield of Paeonia lactiflora Pallas L.. In case of top ground part, growth of irrigation treatment at early growing stage(from May 1 to June 12) was larger(stem length of 79.4cm) or thicker(stem diameter of 6.5mm) than stem length of 13.6∼7.4cm and stem diameter of 0.5mm of natural plot and control. The growth of under ground part, root length(34.0cm) and number of root/plant(43.6ea/plant) in irrigation treatment at early growing stage were relatively larger or more number than that of control, and root yield was gained 2,349kg/10a and increased 13% and 8% compare with natural plot and control, respectively. Commercial ratio of root was higher for irrigation treatment at early growing stage, it was increased by 20% than 1,708kg/10a of natural plot.

• Journal of Korean Neurosurgical Society
• /
• v.39 no.2
• /
• pp.87-91
• /
• 2006

Objective : Management of recurrent vestibular schwannomas[VS] after microsurgery or radiosurgery is a complicated subject. However, few studies have documented the outcome of recurrent VS. The authorsreviewclinicalexperience of recurrent VS management and analyzed the efficacy of treatment modalities. Methods : Between 1990 and 2002, 293 patients harboring unilateral VS underwent, microsurgery, radiosurgery, microsurgery followed by radiosurgery. Of these, 26 procedures [in 20 patients] were performed to assessed from an increased tumor size by magnetic resonance imaging[MRI]. The mean age of patients with recurred VS was 46.9 years and the mean follow-up period was 68 months. Radiological characteristics were investigated and growth rates of recurred tumors were calculated by measuring changes in tumor diameter on MRI after treatment. Results : MRI characteristics revealed a lobulated contour in 75% and a cyst in 60% of the patients. Only 1 patient showed neither lobulation nor a cyst. The average diameter of the recurrent tumors were 36.9mm. The overall tumor control rate for initial management was 87.4%, 94.7%, and 98.5% for microsurgery, radiosurgery, and microsurgery plus radiosurgery, respectively. However, control rates for recurrent tumors were lower at 85%, 63%, and 80%, respectively. Conclusion : A cystic nature and a lobulated tumor contour are frequent clinical characteristics of recurrent VS. Microsurgery or microsurgery followed by radiosurgery shows little difference in tumor control rate for primary and recurrent VS. However, radiosurgery alone appears to be less beneficial for recurrent VS.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.72-76
• /
• 2004

Wetland is an important eco-system on the earth and can effectively control agricultural non-point source pollution. Reed is a typical wetland plant for land/inland water ecotone in north China. The studies indicated that reed had a underground rooted-stem, which formed a 'high speeded-connecting vessels' i.e. reed root channel (RRC) in Baiyangdian lake of Hebei province. It spread predominantly along horizontal direction underground and are mainly distributed at 18-75 cm. The results of field work from healthy reed-wetland (HRW) and regarded reed-wetland (RRW) showed that the reed, averagely, in HRW is 4.2 m height, 1 cm diameter, 65/m2 density; in RRW is 2.4 m height, 3 mm diameter, 86/m2 density. These results indicated the regradation of the function of RRC in RRW. The results of laboratory work of sewage purification from reed soil column (RSC) $(0\~100cm)$ and wheat soil column (WSC) showed that the efficiency of purification to sewage, in RSC, is high than in WSC, especially for phosphorus. The efficiency of purification, in RSC, is $92.6\%$ for total phosphorus, $43.5\%$ for total nitrogen, $54.1\%$ fur COD, respectively; in WSC, is $86.0\%$ for total phosphorus, $241.3\%$ for total nitrogen, $29.8\%$ for COD, respectively.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2001.04b
• /
• pp.39-40
• /
• 2001

This experiment was conducted to investigate the effect of root zone heating on the growth of cut minirose Rosa hybrida L. ′Little Marble′ in winter season. Effects of four different root zone temperatures of 16, 20, 24$^{\circ}C$ and non-heating control on the growth and productivity were compared. Harvested cut-flowers were measured for stem length, stem diameter, fresh and dry weights, numbers of leaves, stems and flowers, days to flower, and chlorophyll concentration. The results showed that mean height was the greatest at 16$^{\circ}C$. Days to flower was the shortest at 24$^{\circ}C$. Fresh and dry weights of top (shoot＋leaf＋flower), shoot and leaf were the greatest at 2$0^{\circ}C$. Stem and flower numbers were the greatest at 16$^{\circ}C$, but leaf number was the greatest at 2$0^{\circ}C$. Mean cut flower yield was the greatest at 16$^{\circ}C$. Chlorophyll concentration was slightly higher at 16$^{\circ}C$, but was not significantly different among the treatments. Stem diameter was the greatest at 2$0^{\circ}C$. Dry matter was the greatest at 24$^{\circ}C$. Total yield of cut rose stems increased with increasing temperature. Combined heating could save 24% in fuel cost as compared to the air heating alone. The results obtained suggested that optimal root zone temperature for the growth of cut rose "Little Marble" was 2$0^{\circ}C$, and the greenhouse heating energy can be saved by minimal air heating combined with root zone heating to 2$0^{\circ}C$.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.718-724
• /
• 2012

Sugars play important roles in petal senescence of cut flowers. In the Expt. 1 of this study, the effects of different concentrations of glucose (60, 90, and $120g{\cdot}L^{-1}$) and sucrose (30, 60, and $90g{\cdot}L^{-1}$) application on the vase life, rate of flower diameter increase, rate of flower weight increase and ethylene production of cut tree peony (Paeonia suffruticosa 'Luoyang Hong') were evaluated. At the earlier stage, treatments of different concentrations of glucose and sucrose all retarded the process of flower opening and inhibited the increase of flower diameter and weight, while senescence of flowers fed with different concentrations of glucose was delayed at later stage. Flowers treated with $90g{\cdot}L^{-1}$ glucose displayed the longest vase life, which showed significant difference (P < 0.05) from those of flowers with the control and sucrose treatments. All treatments with glucose or sucrose not only retarded the decrease of flower diameter and weight, but also suppressed the ethylene production at the earlier stage and delayed the peak of ethylene evolution. In order to study the effect of exogenous sugar on the postharvest response of cut tree peony to ethylene, Expt. 2 was conducted. Cut flowers were treated with $90g{\cdot}L^{-1}$ glucose for 4 hours before (GE) or after (EG) exposed to $10{\mu}L{\cdot}L^{-1}$ ethylene for 4 hours. Generally, the opening process of flowers with GE and EG treatments was similar to that of the control, however GE treatment delayed flower senescence. Both GE and EG treatments improved flower diameter and weight, and GE treatment delayed the time of flower weight decrease. Besides, GE delayed climacteric ethylene evolution for 8 hours. All above suggest that exogenous sugars delay tree peony 'Luoyang Hong' cut flower senescence and extend flower vase life through their roles in the decrease of water loss and the suppression of sensitivity to ethylene and ethylene production.

• Journal of Bio-Environment Control
• /
• v.19 no.4
• /
• pp.275-283
• /
• 2010

This study was conducted to examine the changes in growths of tomato and watermelon seedlings and the relationship among growth parameters which are used to evaluate healthy seedling as affected by shading. Plants were grown under 0%, 25%, 50%, and 75% shadings using polyethylene films. Leaf area index (LAI) of tomato and grafted watermelon seedlings increased under 50% and 75% shading. Total dry weight decreased with increase of shading level. The growth rates of stem diameter, LAI, total weight were faster under 50% and 75% shading with increase of integral radiation than under 0% and 25% shading. Stem diameters of tomato and grafted watermelon seedlings showed no significant differences among shading regimes. Stem diameters of tomato seedlings had upward tendency with increase of total dry weight and shoot height, but there were no significant differences among shading regimes. Stem diameters of grafted watermelon seedlings had no relationship with shoot height. These results indicate that stem diameter of tomato seedlings is not appropriate for assessing seedlings quality but stem diameter of grafted watermelon seedlings with shoot height is available.

• Journal of Bio-Environment Control
• /
• v.18 no.1
• /
• pp.46-50
• /
• 2009

This study was carried to investigate effects of optimum supply strengths of 'Sonneveld' nutrient solution on growth characteristics in container seedling of trees (Pinus densiflora, Torreya nucifera, Quercus acutissina and Fraxinus mandshurica) using developed media with used-rockwool. Flesh weight, height and trunk diameter in container seedling of Torreya nucifera were better in high strengths. In container seed ling of Torreya nucifera, flesh weight more increased in 1.5 and 3.0 strengths and hight and trunk diameter more increased in 1.5 strength than the rest. Flesh weight in container seedling of Quercus acutissina was heaviest in 2.0 strength and was lightest in 1.0 strength. Height and dry weight in 2.0 and 3.0 strengths and trunk diameter and total chlorophyll in 2.0 strength were better than in the rest. Besides photosynthesis rate was more high in 1.5 and 2.0 strengths than in the rest. In container seedling of Fraxinus mandshurica, flesh weight, height and trunk diameter more increased in 0.5 strength and total chlorophyll and photosynthesis rate were good in 0.5 and 2.0 strengths. Most growth characteristics were poor in 3.0 strength.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2349-2351
• /
• 2003

This paper reports a novel microfluidic system, by which microfluidic delivery, transport and control can be digitally realized in femtoliter scale. Microelectronic grade $N_2$ from a pressurized canister was passed through HPLC tubing into a micro injector. The micro injector was driven and controlled digitally by the control system that can apply various control parameters such as pulse frequencies. A front-end of micro nozzle was inserted the dyed oil to collect droplets injected. The diameter of a droplet was measured by a microscope and a CCD camera, and then its volume can be calculated on the assumption that the droplet is spherical. The micro nozzles were simply pulled in glass capillary tubes by the micro puller self-made, and the geometry parameters of the micro nozzles can be adjusted easily. Experiments have successfully been carried out, and the results demonstrated that the proposed digital micro injector possesses three significant advantages : precise ultra-small liquid volume in femtoliter scale, digital microfluidic control and micro devices fabricated by simple glass process, not based on IC process.