• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.355-360
• /
• 1995

In order to align the shaft, the dialgauge method has used as a means of solution until now. The method using a dialgauge require a great deal of labour and money due to making by hand, the accurate alignmentis not up to the expectation. For aligning the shaft, all the rotor must come to accord. It means that the moment of the point of coupling must keep being "Zero". The ideal measurement method as to material on the zero is used by straingauge which can gauge the moment at any point of the shaft. Also, the dialgauge method cannot be compared with straingauge measurement method, form the viewpoint, which can gauge in short time.hort time.

• 한국정밀공학회지
• /
• 제21권3호
• /
• pp.22-29
• /
• 2004

Runout causes severe differences among cutting force waveforms due to changes of rotational radii. Thus a runout model must be included in a cutting force model to simulate cutting force accurately. In this paper, a runout modeling method and a measurement method using a dialgauge were developed, which were easy to apply. To calculate runout parameters, a computer program algorithm which obtained runout parameters from measurement values was developed. Cutting force waveforms simulated from cutting force model considering runout effect and measured from experiments had good agreements for their wave size and order.

• 대한토목학회논문집
• /
• 제2권4호
• /
• pp.39-47
• /
• 1982

본(本) 연구(硏究)에서는 연약점토지반(軟弱粘土地盤) 위에 성토시(盛土時) 보강재(補强材)와 vertical drain재(材)로서의 geotextile의 효과(効果)를 모형실험(模型實驗)을 통(通하)여 조사하였다. 실험은 점토층(粘土層)과 성토층(盛土層) 사이에 woven fabric을 포설(鋪設)하지 않은 경우, fabric을 포설(鋪設)한 경우, fabric에 서로 다른 인위적(人爲的) 인장력(引張力)을 가(加)한 2가지 경우 등 4단계(段階)로 수행(遂行)하였으며 각(各) 단계(段階)마다 압밀(壓密)을 촉진(促進)시키기 위해 non-woven fabric을 사용(使用)한 vertical drain을 점토층(粘土層) 내(內)에 정방형(正方形)으로 배치(配置)하였다. 실험(實驗)모델은 밑면이 $32cm{\times}330cm$이며, 50cm점토층(粘土層) 위에 47cm 높이의 성토제방(盛土堤防)이 1:1.5의 기울기로 만들어졌다. 모형실험대(模型實驗臺)의 양쪽 면에 대칭적(對稱的)으로 8개의 piezometer를 설치(設置)하여 시간(時間)에 따른 공극수압(空隙水壓)을 측정(測定)하였으며 성토제방(盛土堤防) 내부(內部)에 LED램프를 삽입(揷入)하여 시간(時間)에 따른 내부(內部) 변형(變形)을 조사하였고, 제방(堤防)이 설치(設置)되지 않은 점토지반(粘土地盤) 양쪽에는 dialgauge를 부착(附着)하여 융기현상(隆起現象)을 조사하였다. 이러한 실험(實驗)은 1차압밀(次壓密)에 요구(要求)되는 시간(時間)(약(約) 10일(日))동안 수행(遂行)되었다. 실험(實驗)으로부터 점토층(粘土層) 내(內)에 유발(誘發)된 최대과잉공극수압(最大過剩空隙水壓)을 측정(測定)하여 woven fabric을 포설(鋪設)하지 않은 경우의 이론적(理論的)인 최대과잉공극수압(最大過剩空隙水壓)과 비교(比較)함으로써 보강재(補强材)로서의 woven fabric을 포설(鋪設)하였을 경우에도 시간(時間)에 따른 성토부(盛土部) 침하량(沈下量)을 산정(算定)할 수 있음이 밝혀졌다.

• 대한치과보철학회지
• /
• 제37권6호
• /
• pp.730-740
• /
• 1999

The purpose of this study was to investigate setting and thermal expansion of dental soldering investments. In order to compare expansion rates and to investigate the effect of water/powder ratio on expansion, setting and thermal expansion of low dental soldering investments were measured under three different water/powder ratio conditions. standard, 20% decreased and 20% increased. Setting expansion of investments was measured by use of dialgauge method. Each measurement was started two minutes later from the beginning of spatulation and recorded every one minute for one hour. Thermal expansion of cylindrical test specimens, 10mm diameter, 50mm length, was recorded in a thermodilatometer at heating rate of $10^{\circ}C$ per minute from $25^{\circ}C\;to\;700^{\circ}C$. The results of this study were obtained as follows: 1. Setting expansion rates under the standard water/powder ratio condition were 0.198% in Speed-E, 0.090% in Deguvest, 0.080% in CM and Hi-temp. Setting expansion of Speed-E was significantly different from those of CM, Deguvest and Hi-temp, and setting expansion of Deguvest was significantly different from those of CM and Hi-temp(p<.05). 2. Under the decreased water/powder ratio condition, there was significant increase in setting expansion of 4 dental soldering investments (p<.05). 3. There were no significant differences in setting expansions of investments except Hi-temp between standard and increased water/powder ratio condition(p<.05). 4. Thermal expansion rates under the standard water/powder ratio condition were 1.923% in Deguvest, 1.629% in Speed-E, 1.619% in Hi-temp and 1.580% in CM. No significant differences in thermal expansions under the standard water/powder ratio condition existed only between Speed-I and Hi-temp(p<.05) 5. Under the decreased water/powder ratio condition, there was significant increase in thermal expansion of CM and Deguvest but decrease in thermal expansion of Speed-E (p<.05). 6. Under the increased water/powder ratio condition, there was significant decrease in thermal expansion of CM, Deguvest and Speed-I but decrease in thermal expansion of Hi-temp(p<.05).