• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1866-1872
• /
• 2017

This paper presents the design of in-wheel type Switched Reluctance Motor (SRM) which can be used as both traction motor and power pickup device in a wireless charging system of electric vehicles. The SRM acts as a traction drive in driving mode and a power receiver in charging mode to avoid any additional weights. Double stator axial field SRM is used due to its structure that can be mounted inside the wheel. The charging circuit is integrated with the asymmetric converter and phase windings of SRM, reducing the cost and size of the system. Magnetic resonance is implemented to increase the efficiency. Simulations done in Maxwell and Simplorer verify the effectiveness of the proposed system.

• International Journal of Safety
• /
• v.10 no.1
• /
• pp.22-31
• /
• 2011

Seismic response control method of the bridge structures with semi-active control device, i.e., magneto-rheological (MR) damper, is studied in this paper. Design of various kinds of clipped optimal controller and fuzzy controller are suggested as a semi-active control algorithm. For determining the control force of MR damper, clipped optimal control method adopts bi-state approach, but the fuzzy control method continuously quantifies input currents through fuzzy inference mechanism to finely modulate the damper force. To investigate the performances of the suggested control techniques, numerical simulations of a multi-span continuous bridge system subjected to various earthquakes are performed, and their performances are compared with each other. From the comparison of results, it is shown that the fuzzy control system can provide well-balanced control force between girder and pier in the view point of structural safety and stability and be quite effective in reducing both girder and pier displacements over the existing control method.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.686-693
• /
• 2010

In this paper, a fault diagnosis method based on fuzzy logic for the three-parallel power converter in a wind turbine system is presented. The method can not only detect both open and short faults but can also identify faulty switching devices without additional voltage sensors or an analysis modeling of the system. The location of a faulty switch can be indicated by six-patterns of a stator current vector and the fault switching device detection is achieved by analyzing the current vector. A fault tolerant algorithm is also presented to maintain proper performance under faulty conditions. The reliability of the proposed fault detection technique has been proven by simulations and experiments with a 10kW simulator.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.357-358
• /
• 2015

This paper provides a comparison of power converter loss and thermal description for voltage source and current source type 5MW-class medium voltage topologies of wind turbines. Neutral-point clamped three-level converter is adopted for voltage source type topology while two-level converter is employed for current source type topology considering the popularity in the industry. In order to match the required voltage level of 4160V with the same switching device of IGCT as in voltage source converter, two active switches are connected in series for the case of current source converter. The loss analysis is confirmed through PLECS simulations. In addition, the loss factors due to di/dt and dv/dt snubber and ac input filter are presented. The comparison result shows that VSC-based wind turbine system has a higher efficiency than that of CSC under the rated operating conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.127-132
• /
• 2020

In this study, single-phase and three-level boost converters applied to the photovoltaic system were compared and analyzed in terms of efficiency and power density according to the input voltage and load conditions. For accurate analysis of efficiency, the losses in each device of the single-phase and three-level boost converters were derived using mathematical equations and simulations by using the PSIM thermal module. Then, the losses were compared with the efficiency confirmed through the actual experiments. Results confirmed that the efficiency and power density can be improved by applying the three-level boost converter to the system according to the selection of the switching frequency.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.156-158
• /
• 1998

This paper presents parallel operation of two 3-phase PWM converters whose Power and control schemes can be directly applied to a large capacity system. This paper describes power circuit, dc voltage regulation, input power factor correction and balancing load control of two converters. Switching device Is IGBT and CPU of control is 32-bit floating point DSP for real time instantaneous control. Simulations and experimental results for 20kw model conform the validity of proposed schemes.

• Journal of Information Processing Systems
• /
• v.13 no.6
• /
• pp.1602-1612
• /
• 2017

Since rapidly disseminating of Internet of Things (IoT) as the new communication paradigm, a number of studies for various applications is being carried out. Especially, interest in the smart medical system is rising. In the smart medical system, a number of medical devices are distributed in popular area such as station and medical center, and this high density of medical device distribution can cause serious performance degradation of communication, referred to as the coexistence problem. When coexistence problem occurs in smart medical system, reliable transmitting of patient's biological information may not be guaranteed and patient's life can be jeopardized. Therefore, coexistence problem in smart medical system should be resolved. In this paper, we propose a distributed coexistence mitigation scheme for IoT-based smart medical system which can dynamically avoid interference in coexistence situation and can guarantee reliable communication. To evaluate the performance of the proposed scheme, we perform extensive simulations by comparing with IEEE 802.15.4 MAC protocol which is a traditional low-power communication technology.

• Smart Structures and Systems
• /
• v.9 no.6
• /
• pp.549-563
• /
• 2012

Theoretical analysis is performed on a multi-mode energy harvester design with focus on the first two vibration modes. Based on the analysis, a modification is proposed for designing a novel adaptive multi-mode energy harvester. The device comprises a simply supported beam with distributed mass and piezoelectric elements, and an adaptive damper that provides a 180 degree phase shift for the motions of two supports only at the second vibration mode. Theoretical analysis and numerical simulations show that the new design can efficiently scavenge energy at the first two vibration modes. The energy harvesting capability of the multi-mode energy harvester is also compared with that of a cantilever-based energy harvester for single-mode vibration. The results show that the energy harvesting capacity is affected by the damping ratios of different designs. For fixed damping ratio and design dimensions, the multi-mode design has higher energy harvesting capacity than the cantilever-based design.

• Smart Structures and Systems
• /
• v.24 no.1
• /
• pp.141-155
• /
• 2019

This work evaluates the influence of negative stiffness on the performances of various vehicle suspension systems, and proposes a re-centering negative stiffness device (NSD). The re-centering NSD consists of a passive magnetic negative stiffness spring and a positioning shaft with a re-centering function. The former produces negative stiffness control forces, and the latter prevents the amplification of static spring deflection. The numerical simulations reveal that negative stiffness can improve the ride comfort of a vehicle without affecting its road holding abilities for either passive or semi-active suspension systems. In general, the improvement degree of ride comfort increases as negative stiffness increases. For passive suspension system, negative stiffness brings in negative stiffness feature in the control forces, which is helpful for the ride comfort of a vehicle. For semi-active suspensions, negative stiffness can alleviate the impact of clipped damping in semi-active dampers, and thus the ride comfort of a vehicle can be improved.

• Journal of the Korean Physical Society
• /
• v.73 no.10
• /
• pp.1502-1505
• /
• 2018

We present a design for hybrid circular Bragg gratings (hCBGs) for efficiently extracting single-photons emitted by InAs quantum dots (QDs) embedded in GaAs. Finite-difference time-domain simulations show that a very high photon collection efficiency (PCE) up to 96% over a 50 nm bandwidth and pronounced Purcell factors up to 19 at cavity resonance are obtained. We also systematically investigate the geometry parameters, including the $SiO_2$ thickness, grating period, gap width and the central disk radius, to improve the device performances. Finally, the PCEs and the Purcell factors of QDs located at different positions of the hCBG are studied, and the results show great robustness against uncertainties in the location of the QD.