• Journal of Korean Academy of Nursing
• /
• v.47 no.6
• /
• pp.794-805
• /
• 2017

Purpose: Interface pressure is a factor that contributes to the occurrence of pressure injuries. This study aimed to investigate interface pressure at common sites of pressure injury (occipital, gluteal and peritrochanteric areas), to explore the relationships among risk factors, skin condition and interface pressure, and to identify risk factors influencing interface pressure. Methods: A total of 100 patients admitted to the intensive care unit were enrolled at a tertiary teaching hospital in Korea. Interface pressure was recorded by a scanning aid device (PalmQ). Patient data regarding age, pulmonary disease, Braden Scale score, body mass index, serum albumin, hemoglobin, mean blood pressure, body temperature, and oxygen saturation were included as risk factors. Data collected from July to September 2016 were analyzed using binary logistic regression. Results: The mean interface pressure of the occipital, gluteal, and right and left peritrochanteric areas were 37.96 (${\pm}14.90$), 41.15 (${\pm}16.04$), 53.44(${\pm}24.67$), and 54.33 (${\pm}22.80$) mmHg, respectively. Predictive factors for pressure injuries in the occipital area were age ${\geq}70$ years (OR 3.45, 95% confidence interval [CI]: 1.19~9.98), serum albumin deficit (OR 2.88, 95% CI: 1.00~8.26) and body temperature ${\geq}36.5^{\circ}C$ (OR 3.12, 95% CI: 1.17~8.17); age ${\geq}70$ years (OR 2.81, 95% CI: 1.10~7.15) in the right peritrochanteric area; and body temperature ${\geq}36.5^{\circ}C$ (OR 2.86, 95% CI: 1.17~6.98) in the left peritrochanteric area. Conclusion: Our findings suggest that old age, hypoalbuminemia, and high body temperature may be contributory factors to increasing interface pressure; therefore, careful assessment and nursing care of these patients are needed to prevent pressure injury. Further studies are needed to establish cutoff values of interface pressure for patients with pressure ulcers.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.4
• /
• pp.47-53
• /
• 2011

The Electric Multiple Unit (EMU) has many types of door system such as sliding door, plug door etc.al. according to customer's requirements. The sliding door is widely used in Korea but has weak point in the noise problem. In the low operation speed, the noise coming from outer side of the EMU is not an important factor. As the speed is higher than before, noise is increased and make a problem. The main cause of noise is the imperfect air tightness in the EMU. The plug door system has advantages for the noise reduction characteristic in the high speed area. We have been developing electric plug-in door. The door is controlled by Door Control Unit(DCU) following the order of Automatic Train Protection (ATP) that is a kind of train signalling system. DCU has to simultaneously open and close the doors and the operation of it is related to the passengers safety. So DCU is a safety device that is important to reliability and safety. DCU is composed of several devices of control, motor driving, Input/Output, communication and power. In this paper, we will describe the functions, characteristic, requirement, subsystem and test results of DCU used for the electric plug-in door.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.827-836
• /
• 2018

In this study, we developed a PC - based motorcycle simulator based on the development technology of a virtual patrol motorcycle training system. This simulator has been developed to be applied to a variety of fields such as driving training for beginners, driver factor research, and system development such as ABS, which can be seen in advanced models. The weight of the motorcycle operated by the patrol guards is more than 400Kg. There is a lot of risk due to the nature of work without prior practice. Therefore, we implemented a study on the untilization of physical stress and temporal pressure in emergency situations. In order to get a feeling that the motorcycle simulator is operating in real-life, it is important that the mutual reliable signal transmission and operation feel between the driver and the simulator. In order to achieve this, we developed a system that can apply the sub-systems of the actual vehicle to the motorcycle simulator in order to generate the same operation feeling as the actual vehicle. Based on these results, we have developed a method of generating a feedback queue.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.127-136
• /
• 2008

Geophysical survey for establishing a wide site for the distribution of water content, wetting front infiltration due to the rainfall, and distribution of groundwater level has been performed by using 8round penetration radar (GPR) method, electrical resistivity method, and so on. On the other hand, a narrow area survey was performed to use a permittivity method such as time domain reflectometry, frequency domain reflectometry, and amplitude domain reflectometry methods for estimating volumetric water content, soil density, and concentration of contaminant in surface and subsurface. The permittivity methods establish more corrective physical parameters than different found survey technologies mentioned above. In this study for establishment of infiltration behaviors for wetting front in the unsaturated soil caused by an artificial rainfall, soil physical parameters for volumetric water content, pore water pressure, and pore air pressure were measured by FDR measurement device and pore water pressure meter which are installed in the unsaturated weathered granite soil with different depths. Consequently, the authors were proposed to a new establishment method for analyzing the variations of volumetric water content and wetting front infiltration from the responses of infiltrating pore water in the unsaturated soil.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.283-290
• /
• 1999

The $n^+/p/p^+$ junction PERL solar cell of $0.1{\sim}2{\Omega}{\cdot}cm$ (100) p type silicon wafer was fabricated through the following steps; that is, wafer cutting, inverted pyramidally textured surfaces etching by KOH, phosphorus and boron diffusion, anti-reflection coating, grid formation and contact annealing. At this time, the optical characteristics of device surface and the efficiency of doping concentration for resistivity were investigated. And diffusion depth and doping concentration for n+ doping were simulated by silvaco program. Then their results were compared with measured results. Under the illumination of AM (air mass)1.5, $100\;mW/cm^2$ $I_{sc}$, $V_{oc}$, fill factor and the conversion efficiency were 43mA, 0.6 V, 0.62. and 16% respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.369-377
• /
• 2013

This paper deals with the state of charge(SOC) and life cycle evaluation algorithm for lead-acid battery, which is essential factor of the electric vehicle(EV) and the stabilization of renewable energy in the smart grid. In order to perform the effective operation of the lead-acid battery, SOC and life cycle evaluation algorithm is required. Specific gravity with the change of electrolyte temperature inside battery case should be obtained to evaluate the SOC of lead-acid battery, however it is difficult to measure the electrolyte temperature of sealed type lead-acid battery. To overcome this problem, this paper proposes the equation of thermal transmission to compensate internal temperature of the lead-acid battery. Also, it is difficult to exactly evaluate the life cycle of battery, depending on the operation conditions of lead-acid battery such as charging and discharging state, self discharging rate and environmental issue. In order to solve the problem, this paper presents the concept for gravity accumulation of charge and discharge cycle, which is the value converted at $20^{\circ}C$. By using the proposed algorithm, this paper propose the test device based on the Labview software. The simulation results show that it is a practical tool for the maintenance of lead-acid battery in the field of industry.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.5
• /
• pp.513-522
• /
• 2021

A smartphone (SMP) includes a MEMS sensor that can record 3-components motions and has a wireless network device to transmit data in live. These features and relatively low maintenance costs are the advantage of using SMPs as an auxiliary seismic observation network. Currently, 279 SMPs are monitoring seismic motions. In this study, we compare the SMP records with the seismic station (SS) records to validate SMP records. The data used for comparison are records for five earthquakes that occurred in 2019, which are 321 SS data recorded by the Korea Meteorological Administration and the Korea Institute of Geoscience and Mineral Resources and 145 recorded by SMPs. The analysis shows that the event-term corrected average residual of the SMP MEMS sensor records is 0.59 which indicating that the peak horizontal acceleration by SMP is 1.8 factor bigger than the peak ground acceleration by SS. In addition, the residuals tend to decrease as the installation floor of the smartphone MEMS sensor increases, which is the similar trend with response spectra from SS.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.1
• /
• pp.80-95
• /
• 2015

The purpose of this study was to reduce the drop out rates and enhance the quality of docent training education program in the Nature Heritage Center by providing educational services appropriate to the docents' needs based on the docents satisfaction survey. In this research, we conducted the survey to analyze the importance-satisfaction of natural heritage docent satisfaction in natural heritage docent training programs. The subjects of this survey were 30 docent in Natural Heritage Center. To develop a questionnaire, a factor analysis was conducted, as a result, 6 factors and 22 questions were presented. They are 'curriculum and instruction', 'advice for docent', 'educational environments', 'administrative services', 'support for docents', 'docent life'. The results of t-test, there was a significant difference between importance and satisfaction of the every 22 questions, the mean score of satisfaction(M=3.87, SD=.08) was lower than that of importance(M=4.10, SD=.20). According to ISA, the items located in "concentrate here" were deduced. They are 3 items from administrative services, device for docent, curriculum and instructions. To put in concretely, They were 'lecture content(subject)', 'teaching method', 'service attitude of personnel', 'interest in a docent' Based on these results and descriptive responses from the docents, the strategies for docent satisfaction in natural heritage docents training programs were suggested.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.39-49
• /
• 2011

Recently PBD method, one of acceleration of consolidation methods is used in the soft ground to shorten consolidation time for fast settlement during construction. It is economical and easy to work. Discharge capacity of PBD is sensitive in proportion to thickness of soft ground layer, and drainage of PBD declines due to disturbance effect in surrounding ground by mandrel used for vertical drainage setting and setting machines and type. Also, deviation of discharge capacity is large according to ground condition, construction condition and soil properties. In addition, when embankment loading is not conducted instantly after PBD setting due to rain or lack of embankment material supply, it causes leaving period problems. But cause and analysis of those problems for discharge capacity is lack. So, in this test, ground improvement and discharge capacity is investigated by implementing composite discharge capacity test for analysis of an effect factor of PBD discharge capacity with leaving period. After fixing the vertical drain on a cylindrical cylinder, put churned sample into the cylinder. Then leave 0day, 30day, 60day and 90day. And then, load following the loading step of 30, 70 and 120kPa using a pressure device. As a result, the longer leaving period, discharge capacity is reduced. It is caused by a decrease of discharge area caused by creep transformation moisture absorption of PBD filter after long leaving period.

• Journal of Korean Academy of Oral Health
• /
• v.41 no.4
• /
• pp.290-295
• /
• 2017

Objectives: Dental plaque emits red fluorescence under a visible blue light near the ultra-violet end of the light spectrum. The fluorescence characteristics of each microorganism have been reported in several studies. The aim of this study was to evaluate changes in red fluorescence of oral microorganisms that is affected by blood in the culture media. Methods: The gram-positive Actinomyces naeslundii (AN, KCTC 5525) and Lactobacillus casei (LC, KCTC 3109) and gram negative Prevotella intermedia (PI, KCTC 3692) that are known to emit red fluorescence were used in this study. Each bacterium was activated in broth and cultivated in different agar media at $37^{\circ}C$ for 7 days. Tryptic soy agar with hemin and vitamin $K_3$ (TSA), TSA with sheep blood (TSAB), basal medium mucin (BMM) medium, and BMM with sheep blood (BMMB) were used in this study. Fluorescence due to bacterial growth was observed under 405-nm wavelength blue light using the quantitative light-induced fluorescence-digital (QLF-D) device. The red, green, and blue fluorescence values of colonies were obtained using image-analysis software and the red to green ratio (R/G value) and red to total RGB ratio (R/RGB value) were calculated for quantitative comparison. Results: The QLF-D images of the AN, LC, and PI colonies showed red fluorescence in all media, but the fluorescence of all bacteria was reduced in TSA and BMM media, compared with in TSAB and BMMB media. Both the R/G and the R/RGB values of all bacteria were significantly reduced in growth media without blood (P<0.001). Conclusions: Based on this in vitro study, it can be concluded that red fluorescence of oral bacteria can be affected by growth components, especially blood. Blood-containing medium could be a significant factor influencing red fluorescence of oral bacteria. It can be further hypothesized that bleeding in the oral cavity can increase the red fluorescence of dental plaque.