• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2516-2518
• /
• 2000

In order to reduce the trimming loss for water cooling zone next to finishing block mill in wire rolling, the operational data related to the crop length control of uncooled region was acquired and analyzed. The time deviation of water cooling spray nozzles and the immoderate preset length of uncooled wire rod result in the excessive trimming loss. Therefore, the preset length of uncooled wire rod at each cooling zone are established. The test results of #3 wire rolling mill turned out to be good enough to be expected to increase the ratio of products about 0.15% and establish operational standards of cooling zone.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2658-2663
• /
• 2008

In the present study, we designed a microfluidic flatform that generates monodisperse droplets with diameters ranging from hundreds of nanometers to several micrometers. To generate fine droplets, T-junction and flow-focusing geometry are integrated into the microfluidic channel. Relatively large aqueous droplets are generated at the upstream T-junction and transported toward the flow-focusing geometry, where each droplet is broken up into the targeted size by the action of viscous stresses. Because the droplet prior to rupture blocks the straight channel that leads to the flow-focusing geometry, it moves very slowly by the pressure difference applied between the advancing and receding regions of the moving droplet. This configuration enables very low flow rate of inner fluid and higher flow rate ratio between inner and outer fluids at the flow-focusing region. It is shown that the present microfluidic device can generate droplets with diameters about 1 micrometer size and standard deviation less than 3%.

• ETRI Journal
• /
• v.36 no.4
• /
• pp.617-624
• /
• 2014

Through-silicon via (TSV) technology provides much of the benefits seen in advanced packaging, such as three-dimensional integrated circuits and 3D packaging, with shorter interconnection paths for homo- and heterogeneous device integration. In TSV, a destructive cross-sectional analysis of an image from a scanning electron microscope is the most frequently used method for quality control purposes. We propose a quantitative evaluation method for TSV etch profiles whereby we consider sidewall angle, curvature profile, undercut, and scallop. A weighted sum of the four evaluated parameters, nominally total score (TS), is suggested for the numerical evaluation of an individual TSV profile. Uniformity, defined by the ratio of the standard deviation and average of the parameters that comprise TS, is suggested for the evaluation of wafer-to-wafer variation in volume manufacturing.

• Publications of The Korean Astronomical Society
• /
• v.11 no.1
• /
• pp.263-277
• /
• 1996

We have intensively carried out numerical calculations on flare predictions from the solar activity data for photospheric sunspots, chromospheric flare and plages, coronal X-ray intensities and 2800MHz radio fluxes, by using multilinear regression method. Intensities of solar flares for the next day have been predicted from the solar data between 1977-1982 and 1993-1996. Firstly, we have calculated flare predictions with the multilinear regression method, by using separate solar data in growth and decay phase of sunspot area and magnetic field strength from the whole data on solar activities. Secondly, the same operations as above have been made for the remaining data after removal of the data with large deviation from the mean calculated by the above prediction method. we have reached a conclusion that average hit ratio of correct predictions to total predictions of flares with class of M5 over has been as high as 70% for the first case and that of correct prediction number to total observation number has been shown as 61%.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.1430-1435
• /
• 2006

This study deals with the problem of balance beam system to stabilize about static and sinusoidal disturbance. wherein the design objectives are to keep the gap deviation from static and sinusoidal disturbance. In this paper propose the 2-Degree of Freedom(DOF) structure and a simple first-order controller which is designed by Characteristic ratio assignment (CRA) method. Matlab simulation result verify stabilization of balance beam system despite of disturbance. Hybrid simulation between digital controller and analog plant is presented by Matlab Simulink.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.109-113
• /
• 1999

Thermal mass flow meter (TMF) is used measuring the small mass flow rate of gases. Generally, flow rate measuring accuracy of TMF is $\pm2{\%}$ of full scale. TMF is manufactured for specified working pressure and specified working gas by customer. If it were applied for different working pressure and gases, flow rate measurement accuracy decreased dramatically. In this study, a TMF tested with three different gases and pressure range of 0.2 MPa to 1.0 MPa. Effect of specific heat cause to increase flow measurement error as much as ratio of specific heat compare with reference gas. Pressure change cause to increase flowrate measurement deviation about $-0.2{\%}$ as the working pressure decreased 0.1 MPa.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.92-101
• /
• 2000

The objective of this paper is to design the controller for longitudinal vehicle following which makes the vehicle follow the lead vehicle and keeps a safety distance without human driver operation. This paper presents a sliding mode control algorithm for the ACC system. The controller is based on three sliding surfaces. Each surface plays an individual control-deviation control, throttle control and brake control. In addition to sliding mode control, we propose some additional schemes to enhance controller performance. The first one is a gear shift-down controller which makes tractive force increase with a change of gear ratio. The other is a predictive correction method which reduces slinky effect.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.483-486
• /
• 2005

In order to study the effect of strain states on the formation of shear textures during rolling in fcc metals, the evolution of textures was simulated by the full constrain model using various ideal strain states. Considering rolling as a two-dimensional problem, i.e., $\varepsilon_{22}\;=\;\varepsilon_{12}\;=\;\varepsilon_{23}\;=\;0$, the deviation from the plane-strain state manifest itself as nonzero contribution of $\varepsilon_{13}$. With increasing variations of $\varepsilon_{13}$, shear textures develop. The sign of ell hardly affects the evolution of textures. The texture simulation with various idealized strain states indicates that the ratio $\mid\varepsilon_{13}\mid/\mid\varepsilon_{11}\mid$ in each time interval in a roll gap plays a dominant role in the evolution of textures during rolling.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.15-24
• /
• 1998

In this research. we have proposed a new technique to determine .the combination of design parameters for the process design of a hot forged product using artificial neural network(ANN) and statistical design of experiments(DOE). The investigated problem involves the adequate selection of the aspect ratio of billet, the ram velocity and the friction factor as design parameters. An optimal billet satisfying the forming limitation, die filling, load and energy as well as more uniform distribution of effective strain, is determined by applying the ability of artificial neural network and considering the analysis of mean and variation on the functional requirement. This methodology will be helpful in designing and controlling parameters on the shop floor which would yield the best design solution.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.204-205
• /
• 2016

Human power is not dependent on other energy sources, but rather is a source of power for ourselves. Human power, the cleanest energy in the world, can be our future. Therefore, we should be interested in sustainable alternative energy. This paper solves the uneven power generation by utilizing the energy storage capability of the flywheel. Therefore, it improved the efficiency by 5% compared to the existing generation method. DC generators produce power at variable speed operation. The constant voltage was generated from the DC-DC converter to the duty ratio control. Therefore, the charging efficiency is improved by 5% by the constant voltage charging of the battery. And it can suppress the decrease of the output due to the circulation current due to the deviation of the output voltage in parallel operation of the pedal generator.