• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2503-2510
• /
• 2002

Since the first shape-form-shading technique was developed by Horn in the early 1970s, many different approaches have been continuously emerging in the past three decades. Some of them improve existing techniques, while others are completely new approaches. Using the image reflectance equation, they estimate the 3-D shape of an object utilizing adequate constraints. Each algorithm applies different constraints such as brightness, smoothness, and integrability to solve the shape-from-shading problem. Especially for symmetric objects, a symmetry constraint is proposed to improve the performance of existing shape-from-shading algorithm in this paper. The symmetry constraint is imposed to a conventional algorithm and then the improvement in the performance of 3-D shape reconstruction is proved by quantitatively comparing the depth and gradient errors.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.117-120
• /
• 2002

In this paper, several methods to predict the solder joint shape are studied. Although there are various methods to predict the solder joint shape, such as truncated sphere method, force-bal tranced analytical solution, and energy-based methods like surface evolver developed by Ken Brakke, we calculate solder joint shape of $\mu$BGA by two solder joint shape prediction methods(truncated sphere method and surface evolver) and then compare results of each method. The results in dicate that two methods can accurately predict the solder joint shape in an accurate range. After that, we calculate reliability solder joint shape under thermal cycle test by FEA program ANSYS. As a result, it could be found that optimal solder joint shape calculated by solder joint prediction method has best reliability in thermal cycle test.

• 한국정밀공학회지
• /
• 제13권9호
• /
• pp.54-61
• /
• 1996

Because of its high energy density, the use of shape memory alloys(SMA) in designing microactuatiors is gaining much attention in recent years. Shape memory alloys can undergo a shape change at a low temperature with a small applied deformation force, and retain this deformation until they are heated, at which point they return to the original shape. This is called the shape memory effect(SME), and a plethora of alloys show this effect. Among them, TiNi-based alloys have relatively high electrical resistivity, which to develope helical-shape memory springs. These springs are used to develop fast protatonist/antagonist configuration actuators. The developed actuator has an actuation speed of 1 mm per 15 .approx. 20 ms and a minimum operating period of 2 sec.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1986년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 17-18 Oct. 1986
• /
• pp.102-107
• /
• 1986

This paper presents a new idea to obtain moment of inertia values of an arbitrary shape body by applying inverse modal transformation technique. A multiaxes inertia pendulum apparatus was designed to measure 6 rigid body modes of a test body. A software was developed to calculate inertia properties as well as the location of center of gravity and total mass of the test body from the measured modal data. The developed method was applied to a simple body of which the inertia properties are known then the obtained values were compared with the known values.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.66-68
• /
• 2004

Induction heating is a process that is accompanied with magnetic and thermal situation. When the high-frequency current flows in the coil, induced eddy current generates heat to conductor. To simulate an induction heating process, the finite element analysis program was developed. A coupling method between the magnetic and thermal routines was developed. In the process of magnetic analysis and thermal analysis, magnetic material properties and thermal material properties depending on temperature are taken into consideration. In this paper, to predict the angular deformation, temperature difference and the shape of heat affected zone were discussed. Also appropriate coil shape for maximum angular deformation were proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.706-709
• /
• 2004

A numerical method was developed that imposes constraint condition on the order parameters in martensitic phase transformation. In the method, an amplitude function having values of 1 or 0 was multiplied to transformation rates. The merit of the method is that the imposition of the constraint condition is more straightforward than a method with Lagrangian multiplier and easy to implement in the tangent modulus method. The developed method is applied to three-dimensional finite element analyses of single and poly crystalline shape memory alloys.

• Journal of Computational Design and Engineering
• /
• 제2권1호
• /
• pp.55-66
• /
• 2015

To satisfy safety regulations of Economic Commission for Europe (ECE), the surface regions of automobile parts must have a sufficient degree of roundness if there is any chance that they could contact a sphere of 50.0 mm radius (exterior parts) or 82.5 mm radius (interior parts). In this paper, a new offset-based method is developed to automatically detect the possible sphere-contacting shape of such parts. A polyhedral model that precisely approximates the part shape is given as input, and the offset shape of the model is obtained as the Boolean union of the expanded shapes of all surface triangles. We adopt a triple-dexel representation of the 3D model to enable stable and precise Boolean union computations. To accelerate the dexel operations in these Boolean computations, a new parallel processing method with a pseudo-list structure and axis-aligned bounding box is developed. The possible sphere-contacting shape of the part surface is then extracted from the offset shape as a set of points or a set of polygons.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.211-214
• /
• 2006

The outer race of the constant velocity(CV) joint is an important load-supporting automotive part, which transmits torque between the transmission and the wheel. The outer race is difficult to forge, because its shape is very complex and the required dimensional tolerances are very stringent. Therefore, the internet based shape inspection system is developed in this study to provide quick and accurate data through the easy control from users. Proposed system uses mechanical displacement sensors to measure the shape of CV joint that has six inner ball grooves, and commercially available Lab-View program is used to process measured data into the dimensional shape. Developed program provides a simple user interface that enables users real-time access of data measured from industrial production lines. Furthermore, it can exchange measured data via the internet between users and forging system operators. A java applet helped the system connection via internet. A data, IP access, is transmitted to the packet by TCP/IP. Our proposed system has many advantages over current measuring systems including fast and efficient data processing by real-time control, and system flexibility.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.299-306
• /
• 2006

Using a level set method and topological derivatives, a topological shape optimization method that is independent of an initial design is developed for linearly elastic structures. In the level set method, the initial domain is kept fixed and its boundary is represented by an implicit moving boundary embedded in the level set function, which facilitates to handle complicated topological shape changes. The 'Hamilton-Jacobi (H-J)' equation and computationally robust numerical technique of 'up-wind scheme' lead the initial implicit boundary to an optimal one according to the normal velocity field while minimizing the objective function of compliance and satisfying the constraint of allowable volume. Based on the asymptotic regularization concept, the topological derivative is considered as the limit of shape derivative as the radius of hole approaches to zero. The required velocity field to update the H -J equation is determined from the descent direction of Lagrangian derived from optimality conditions. It turns out that the initial holes is not required to get the optimal result since the developed method can create holes whenever and wherever necessary using indicators obtained from the topological derivatives. It is demonstrated that the proper choice of control parameters for nucleation is crucial for efficient optimization process.

• 한국공간구조학회논문집
• /
• 제15권2호
• /
• pp.51-59
• /
• 2015

In this study, a shape design and an analysis considering structural stability were investigated to develop an icosahedron-based hemispherical modular dome. To design this modular dome, a program that can perform icosahedron shape modeling, modularization of joint connection members, and the analysis of structural stability was developed. Furthermore, based on the adopted numerical model, the eigen buckling mode, unstable behavior characteristics according to load vector, and the critical buckling load of the modular dome under uniformly distributed load and concentrated load were analyzed, and the resistance capacities of the structure according to different load vectors were compared. The analysis results for the modular dome suggest that the developed program can perform joint modeling for shape design as well as modular member design, and adequately expressed the nonlinear behaviors of structured according to load conditions. The critical buckling load results also correctly reflected the characteristics of the load conditions. The uniformly distributed load was more advantageous to the structural stability than concentrated load.