• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.147-152
• /
• 2006

The current type amplifier is the device that is used for an actuator as the motor's torque controller. However, it is too difficult to select the parameter value that has the desired output because the current type amplifier's transfer function is too complex. This study concern about the design of the current type amplifier with the desired output. From the modeled transfer function of the current type amplifier, the optimal parameter values of the transfer function can be selected in order to have the desired output using the Real Coded Genetic Algorithm(RCGA). The real circuit is made with the selected parameter value. The step response of the real circuit is in good agreement with the desired step response.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.11
• /
• pp.1013-1021
• /
• 2000

This paper suggests fuzzy-PI controllers for a heavy-duty gas turbine. The fuzzy-PI controllers are designed to regulate rotor speed and exhaust temperature of the gas turbine. The controller gains are tuned by genetic algorithm(GA). This paper also proposes a new fitness function of GA using a desired output response. The suggested controller is compared with previous controllers via simulations and it is shown that the rotor speed variation of our controller is smaller than those of previous ones.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1984.10a
• /
• pp.82-87
• /
• 1984

A 2-D digital filter with rational frequency response can be expanded into an infinite sequence of filterins operations. Each filtering operation can be implemented by convolution with a Low-order 20D finite-extent impulse response. If a convergence constraint is satisfied, the sequence of estimates will approach the desired output signal. In practice, as the number of iterations is finite, the frequency response implemented by iterative computations is an approximation to the desired rational frequency response.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.2
• /
• pp.399-407
• /
• 1996

A fuzzy learning algorithm to get the optimal fuzzy rules is presented in this paper. The algorithm introduces a reference model to generate a desired output and a performance index funtion instead of the performance index table. The performance index funtion is a cost function based on the error and error-rate between the reference and plant output. The cost function is minimized by a gradient method and the control input is also updated. In this case, the control rules which generate the desired response can be obtained by changing the portion of the error-rate in the cost funtion. In SISO(Single-Input Single- Output)plant, only by the learning delay, it is possible to experss the plant model and to get the desired control rules. In the long run, this algorithm gives us the good control rules with a minimal amount of prior informaiton about the environment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.452-456
• /
• 1988

A PID controller must need not only good servo response but also little operation of a control valve. We suggest a direct pole-placement PID self-tuning algorithm using the structure of derivative-of-output controller and Bezout identity. This algorithm can much reduce the change of output of controller and well follow the desired trajectory.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.10a
• /
• pp.29-36
• /
• 1996

A procedure for the predictive control for structural vibration control in building subject to wind loads is presented. The building motions are modeled by the first mode of the response. Wind velocities are generated by the simulation using power spectral density function. Predictive control algorithm is the discrete-time formulation and that is developed as a control strategy that computes the control signal which makes the predicted process output equal to a desired process output. Results on the reduction of the dynamic response and control effectiveness of the algorithm are presented and discussed.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.236-248
• /
• 2017

A direct stator flux vector control scheme in discrete-time domain is proposed in this paper for the interior permanent magnet synchronous motor (IPMSM) drive to remove the proportional-integral (PI) controller from the direct torque control (DTC) scheme applied to IPMSM and to obtain faster dynamic response and lower torque ripple output. The output of speed outer loop is used as the desired torque angle instead of the desired torque in the proposed scheme. The desired stator flux vector in dq coordinate is calculated with a given amplitude. The state-space equations in discrete-time for IPMSM are established, the actual stator flux vector is estimated in deadbeat manner by a full-order state observer, and then the closed-loop control is achieved by the pole placement. The stator flux error vector is utilized to calculate the reference stator voltage vector. Extracting the angle position and amplitude from the estimated stator flux vector and estimating the output torque are eliminated for the direct feedback control of the stator flux vector. The proposed scheme is comparatively investigated with a PI-SVM DTC scheme by experiment results. Experimental results show the feasibility and advantages of the proposed control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.176.5-176
• /
• 2001

This paper presents a fuzzy dynamic output feedback controller design method for Parallel Distributed Compensation (PDC)-type Takagi-Sugeno (T-S) model based fuzzy dynamic system with H$\infty$ performance and additional constraints on the closed pole placement. Design condition for these controller is obtained in terms of the linear matrix inequalities (LMIs). The proposed fuzzy controller satisfies the disturbance rejection performance and the desired transient response. The design method is verified by this method for an inverted pendulum with a cart using the proposed method.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.48-54
• /
• 2015

This paper introduced a design method of soldering station that can control two types of soldering iron heater. At design time, to distinguish two types of soldering iron heater the voltage divider rule has been applied, and the distinguished resistor is inserted to handler of soldering iron to prevent misuse by users. And an algorithm to design a PID controllers is proposed. The proposed controllers parameter which can be easily realized, and are designed by using the input output data from systems, and have outstanding ability making the output response of nonlinear systems similar to the desired one. Temperature control experiments were performed to verify the ability of the suggested controller. As a result, suggested PID controller followed the desired ones, and one soldering station can control the various type of soldering irons in real time.

• The Journal of Asian Finance, Economics and Business
• /
• v.6 no.3
• /
• pp.103-113
• /
• 2019

The effectiveness of monetary policy critically depends upon how well the transmission mechanism functions, so that the desired impact on output and inflation is achieved. The purpose of this paper is to study the transmission mechanism of monetary policy by analyzing the impact on inflation and output during multiple indicator regime (1998-99 to 2014) in an emerging economy-India. The Inflation Targeting Regime is also briefly outlined alongwith the impact on output and inflation. Using quarterly data for the period 1997 to 2017, the paper uses weighted average call money market rate as a proxy for the policy rate and evaluates the strength of the interest rate channel. We use a conventional Structural vector auto regression (SVAR) methodology to evaluate the efficacy and show the impluse response functions. Our results find that changes in the policy rate impact output growth steeply with a lag of about two quarters and the impact on inflation is maximized after three quarters. The study concludes that the monetary policy in India has a significant impact on output and inflation in the short-to-medium-run. After the policy shock, the fall in the output growth rate is of greater magnitude than the fall in inflation.